[U-Boot] [u-boot 24/40] usb: dwc3: dwc3-omap: make dwc3-omap build in uboot
Lukasz Majewski
l.majewski at samsung.com
Mon Feb 16 12:02:51 CET 2015
Hi Kishon,
> *) Changed the included header files to that used in u-boot.
> *) Removed extcon_* APIs
> *) Removed regulator_* APIs
> *) Fixed other misc warnings
> *) Added dwc3-omap.h to include the definitions of UTMI modes.
>
> Signed-off-by: Kishon Vijay Abraham I <kishon at ti.com>
> ---
> drivers/usb/dwc3/dwc3-omap.c | 144
> +++--------------------------------------
> include/linux/usb/dwc3-omap.h | 19 ++++++ 2 files changed, 27
> insertions(+), 136 deletions(-) create mode 100644
> include/linux/usb/dwc3-omap.h
>
> diff --git a/drivers/usb/dwc3/dwc3-omap.c
> b/drivers/usb/dwc3/dwc3-omap.c index ce2d6a6..b385987 100644
> --- a/drivers/usb/dwc3/dwc3-omap.c
> +++ b/drivers/usb/dwc3/dwc3-omap.c
> @@ -14,21 +14,16 @@
> * SPDX-License-Identifier: GPL-2.0
> */
>
> -#include <linux/module.h>
> -#include <linux/kernel.h>
> -#include <linux/slab.h>
> -#include <linux/interrupt.h>
> -#include <linux/platform_device.h>
> -#include <linux/platform_data/dwc3-omap.h>
> -#include <linux/dma-mapping.h>
> +#include <common.h>
> +#include <malloc.h>
> +#include <asm/io.h>
> +#include <linux/usb/dwc3-omap.h>
> #include <linux/ioport.h>
> -#include <linux/io.h>
> -#include <linux/of.h>
> -#include <linux/of_platform.h>
> -#include <linux/extcon.h>
> -#include <linux/regulator/consumer.h>
>
> #include <linux/usb/otg.h>
> +#include <linux/compat.h>
> +
> +#include "linux-compat.h"
>
> /*
> * All these registers belong to OMAP's Wrapper around the
> @@ -113,7 +108,6 @@
> struct dwc3_omap {
> struct device *dev;
>
> - int irq;
> void __iomem *base;
>
> u32 utmi_otg_status;
> @@ -124,13 +118,6 @@ struct dwc3_omap {
> u32 irq0_offset;
>
> u32 dma_status:1;
> -
> - struct extcon_specific_cable_nb extcon_vbus_dev;
> - struct extcon_specific_cable_nb extcon_id_dev;
> - struct notifier_block vbus_nb;
> - struct notifier_block id_nb;
> -
> - struct regulator *vbus_reg;
> };
>
> enum omap_dwc3_vbus_id_status {
> @@ -205,21 +192,12 @@ static void dwc3_omap_write_irq0_set(struct
> dwc3_omap *omap, u32 value) static void dwc3_omap_set_mailbox(struct
> dwc3_omap *omap, enum omap_dwc3_vbus_id_status status)
> {
> - int ret;
> u32 val;
>
> switch (status) {
> case OMAP_DWC3_ID_GROUND:
> dev_dbg(omap->dev, "ID GND\n");
>
> - if (omap->vbus_reg) {
> - ret = regulator_enable(omap->vbus_reg);
> - if (ret) {
> - dev_dbg(omap->dev, "regulator enable
> failed\n");
> - return;
> - }
> - }
> -
> val = dwc3_omap_read_utmi_status(omap);
> val &= ~(USBOTGSS_UTMI_OTG_STATUS_IDDIG
> | USBOTGSS_UTMI_OTG_STATUS_VBUSVALID
> @@ -242,9 +220,6 @@ static void dwc3_omap_set_mailbox(struct
> dwc3_omap *omap, break;
>
> case OMAP_DWC3_ID_FLOAT:
> - if (omap->vbus_reg)
> - regulator_disable(omap->vbus_reg);
> -
> case OMAP_DWC3_VBUS_OFF:
> dev_dbg(omap->dev, "VBUS Disconnect\n");
>
> @@ -349,32 +324,6 @@ static void dwc3_omap_disable_irqs(struct
> dwc3_omap *omap)
> static u64 dwc3_omap_dma_mask = DMA_BIT_MASK(32);
>
> -static int dwc3_omap_id_notifier(struct notifier_block *nb,
> - unsigned long event, void *ptr)
> -{
> - struct dwc3_omap *omap = container_of(nb, struct dwc3_omap,
> id_nb); -
> - if (event)
> - dwc3_omap_set_mailbox(omap, OMAP_DWC3_ID_GROUND);
> - else
> - dwc3_omap_set_mailbox(omap, OMAP_DWC3_ID_FLOAT);
> -
> - return NOTIFY_DONE;
> -}
> -
> -static int dwc3_omap_vbus_notifier(struct notifier_block *nb,
> - unsigned long event, void *ptr)
> -{
> - struct dwc3_omap *omap = container_of(nb, struct dwc3_omap,
> vbus_nb); -
> - if (event)
> - dwc3_omap_set_mailbox(omap, OMAP_DWC3_VBUS_VALID);
> - else
> - dwc3_omap_set_mailbox(omap, OMAP_DWC3_VBUS_OFF);
> -
> - return NOTIFY_DONE;
> -}
> -
> static void dwc3_omap_map_offset(struct dwc3_omap *omap)
> {
> struct device_node *node = omap->dev->of_node;
> @@ -420,42 +369,6 @@ static void dwc3_omap_set_utmi_mode(struct
> dwc3_omap *omap) dwc3_omap_write_utmi_status(omap, reg);
> }
>
> -static int dwc3_omap_extcon_register(struct dwc3_omap *omap)
> -{
> - int ret;
> - struct device_node *node = omap->dev->of_node;
> - struct extcon_dev *edev;
> -
> - if (of_property_read_bool(node, "extcon")) {
> - edev = extcon_get_edev_by_phandle(omap->dev, 0);
> - if (IS_ERR(edev)) {
> - dev_vdbg(omap->dev, "couldn't get extcon
> device\n");
> - return -EPROBE_DEFER;
> - }
> -
> - omap->vbus_nb.notifier_call =
> dwc3_omap_vbus_notifier;
> - ret =
> extcon_register_interest(&omap->extcon_vbus_dev,
> - edev->name, "USB",
> - &omap->vbus_nb);
> - if (ret < 0)
> - dev_vdbg(omap->dev, "failed to register
> notifier for USB\n"); -
> - omap->id_nb.notifier_call = dwc3_omap_id_notifier;
> - ret = extcon_register_interest(&omap->extcon_id_dev,
> - edev->name,
> "USB-HOST",
> - &omap->id_nb);
> - if (ret < 0)
> - dev_vdbg(omap->dev, "failed to register
> notifier for USB-HOST\n"); -
> - if (extcon_get_cable_state(edev, "USB") == true)
> - dwc3_omap_set_mailbox(omap,
> OMAP_DWC3_VBUS_VALID);
> - if (extcon_get_cable_state(edev, "USB-HOST") == true)
> - dwc3_omap_set_mailbox(omap,
> OMAP_DWC3_ID_GROUND);
> - }
> -
> - return 0;
> -}
> -
> static int dwc3_omap_probe(struct platform_device *pdev)
> {
> struct device_node *node = pdev->dev.of_node;
> @@ -463,11 +376,8 @@ static int dwc3_omap_probe(struct
> platform_device *pdev) struct dwc3_omap *omap;
> struct resource *res;
> struct device *dev = &pdev->dev;
> - struct regulator *vbus_reg = NULL;
>
> int ret;
> - int irq;
> -
> u32 reg;
>
> void __iomem *base;
> @@ -483,29 +393,13 @@ static int dwc3_omap_probe(struct
> platform_device *pdev)
> platform_set_drvdata(pdev, omap);
>
> - irq = platform_get_irq(pdev, 0);
> - if (irq < 0) {
> - dev_err(dev, "missing IRQ resource\n");
> - return -EINVAL;
> - }
> -
> res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> base = devm_ioremap_resource(dev, res);
> if (IS_ERR(base))
> return PTR_ERR(base);
>
> - if (of_property_read_bool(node, "vbus-supply")) {
> - vbus_reg = devm_regulator_get(dev, "vbus");
> - if (IS_ERR(vbus_reg)) {
> - dev_err(dev, "vbus init failed\n");
> - return PTR_ERR(vbus_reg);
> - }
> - }
> -
> omap->dev = dev;
> - omap->irq = irq;
> omap->base = base;
> - omap->vbus_reg = vbus_reg;
> dev->dma_mask = &dwc3_omap_dma_mask;
>
> dwc3_omap_map_offset(omap);
> @@ -515,34 +409,16 @@ static int dwc3_omap_probe(struct
> platform_device *pdev) reg = dwc3_omap_readl(omap->base,
> USBOTGSS_SYSCONFIG); omap->dma_status = !!(reg &
> USBOTGSS_SYSCONFIG_DMADISABLE);
> - ret = devm_request_irq(dev, omap->irq, dwc3_omap_interrupt,
> 0,
> - "dwc3-omap", omap);
> - if (ret) {
> - dev_err(dev, "failed to request IRQ #%d --> %d\n",
> - omap->irq, ret);
> - goto err0;
> - }
> -
> dwc3_omap_enable_irqs(omap);
>
> - ret = dwc3_omap_extcon_register(omap);
> - if (ret < 0)
> - goto err1;
> -
> ret = of_platform_populate(node, NULL, NULL, dev);
> if (ret) {
> dev_err(&pdev->dev, "failed to create dwc3 core\n");
> - goto err2;
> + goto err1;
> }
>
> return 0;
>
> -err2:
> - if (omap->extcon_vbus_dev.edev)
> - extcon_unregister_interest(&omap->extcon_vbus_dev);
> - if (omap->extcon_id_dev.edev)
> - extcon_unregister_interest(&omap->extcon_id_dev);
> -
> err1:
> dwc3_omap_disable_irqs(omap);
>
> @@ -554,10 +430,6 @@ static int dwc3_omap_remove(struct
> platform_device *pdev) {
> struct dwc3_omap *omap = platform_get_drvdata(pdev);
>
> - if (omap->extcon_vbus_dev.edev)
> - extcon_unregister_interest(&omap->extcon_vbus_dev);
> - if (omap->extcon_id_dev.edev)
> - extcon_unregister_interest(&omap->extcon_id_dev);
> dwc3_omap_disable_irqs(omap);
> device_for_each_child(&pdev->dev, NULL,
> dwc3_omap_remove_core);
> diff --git a/include/linux/usb/dwc3-omap.h
> b/include/linux/usb/dwc3-omap.h new file mode 100644
> index 0000000..8bf7b55
> --- /dev/null
> +++ b/include/linux/usb/dwc3-omap.h
> @@ -0,0 +1,19 @@
> +/* include/linux/usb/dwc3-omap.h
> + *
> + * Copyright (c) 2014 Texas Instruments Incorporated -
> http://www.ti.com
> + *
> + * Designware SuperSpeed Glue
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __DWC3_OMAP_H_
> +#define __DWC3_OMAP_H_
> +
> +enum dwc3_omap_utmi_mode {
> + DWC3_OMAP_UTMI_MODE_UNKNOWN = 0,
> + DWC3_OMAP_UTMI_MODE_HW,
> + DWC3_OMAP_UTMI_MODE_SW,
> +};
> +
> +#endif /* __DWC3_OMAP_H_ */
Reviewed-by: Lukasz Majewski <l.majewski at samsung.com>
--
Best regards,
Lukasz Majewski
Samsung R&D Institute Poland (SRPOL) | Linux Platform Group
More information about the U-Boot
mailing list