[U-Boot] [PATCH v4 17/20] ARM: UniPhier: support 1CS support card for all the UniPhier SoCs
Masahiro Yamada
yamada.m at jp.panasonic.com
Tue Feb 24 05:43:21 CET 2015
Two support card variants are used with UniPhier reference boards:
- 1 chip select support card (original CPLD)
- 3 chip selects support card (ARIMA-compatible CPLD)
Currently, the former is only supported on PH1-Pro4, but it can be
expanded to PH1-LD4, PH1-sLD8 with a little code change.
Signed-off-by: Masahiro Yamada <yamada.m at jp.panasonic.com>
---
Changes in v4: None
Changes in v3: None
Changes in v2: None
arch/arm/mach-uniphier/ph1-ld4/Makefile | 4 +-
arch/arm/mach-uniphier/ph1-ld4/sbc_init.c | 51 +---------------------
arch/arm/mach-uniphier/ph1-ld4/sbc_init_3cs.c | 50 ++++++++++++++++++++++
arch/arm/mach-uniphier/ph1-pro4/Makefile | 4 +-
arch/arm/mach-uniphier/ph1-pro4/sbc_init.c | 32 --------------
arch/arm/mach-uniphier/ph1-pro4/sbc_init_3cs.c | 43 +++++++++++++++++++
arch/arm/mach-uniphier/ph1-sld8/Makefile | 4 +-
arch/arm/mach-uniphier/ph1-sld8/sbc_init.c | 59 +-------------------------
arch/arm/mach-uniphier/ph1-sld8/sbc_init_3cs.c | 58 +++++++++++++++++++++++++
9 files changed, 162 insertions(+), 143 deletions(-)
create mode 100644 arch/arm/mach-uniphier/ph1-ld4/sbc_init_3cs.c
create mode 100644 arch/arm/mach-uniphier/ph1-pro4/sbc_init_3cs.c
create mode 100644 arch/arm/mach-uniphier/ph1-sld8/sbc_init_3cs.c
diff --git a/arch/arm/mach-uniphier/ph1-ld4/Makefile b/arch/arm/mach-uniphier/ph1-ld4/Makefile
index 927640a..5ce3d8a 100644
--- a/arch/arm/mach-uniphier/ph1-ld4/Makefile
+++ b/arch/arm/mach-uniphier/ph1-ld4/Makefile
@@ -4,8 +4,10 @@
ifdef CONFIG_SPL_BUILD
obj-$(CONFIG_DEBUG_LL) += lowlevel_debug.o
-obj-y += bcu_init.o sbc_init.o sg_init.o pll_init.o early_clkrst_init.o \
+obj-y += bcu_init.o sg_init.o pll_init.o early_clkrst_init.o \
pll_spectrum.o umc_init.o ddrphy_init.o
+obj-$(CONFIG_PFC_MICRO_SUPPORT_CARD) += sbc_init.o
+obj-$(CONFIG_DCC_MICRO_SUPPORT_CARD) += sbc_init_3cs.o
else
obj-$(CONFIG_BOARD_EARLY_INIT_F) += pinctrl.o clkrst_init.o
obj-$(if $(CONFIG_OF_CONTROL),,y) += platdevice.o
diff --git a/arch/arm/mach-uniphier/ph1-ld4/sbc_init.c b/arch/arm/mach-uniphier/ph1-ld4/sbc_init.c
index 374a8c0..656d7d7 100644
--- a/arch/arm/mach-uniphier/ph1-ld4/sbc_init.c
+++ b/arch/arm/mach-uniphier/ph1-ld4/sbc_init.c
@@ -1,50 +1 @@
-/*
- * Copyright (C) 2011-2015 Panasonic Corporation
- * Author: Masahiro Yamada <yamada.m at jp.panasonic.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <mach/sbc-regs.h>
-#include <mach/sg-regs.h>
-
-void sbc_init(void)
-{
- u32 tmp;
-
- /* system bus output enable */
- tmp = readl(PC0CTRL);
- tmp &= 0xfffffcff;
- writel(tmp, PC0CTRL);
-
- /* XECS1: sub/boot memory (boot swap = off/on) */
- writel(SBCTRL0_SAVEPIN_MEM_VALUE, SBCTRL10);
- writel(SBCTRL1_SAVEPIN_MEM_VALUE, SBCTRL11);
- writel(SBCTRL2_SAVEPIN_MEM_VALUE, SBCTRL12);
- writel(SBCTRL4_SAVEPIN_MEM_VALUE, SBCTRL14);
-
- /* XECS0: boot/sub memory (boot swap = off/on) */
- writel(SBCTRL0_SAVEPIN_MEM_VALUE, SBCTRL00);
- writel(SBCTRL1_SAVEPIN_MEM_VALUE, SBCTRL01);
- writel(SBCTRL2_SAVEPIN_MEM_VALUE, SBCTRL02);
- writel(SBCTRL4_SAVEPIN_MEM_VALUE, SBCTRL04);
-
- /* XECS3: peripherals */
- writel(SBCTRL0_SAVEPIN_PERI_VALUE, SBCTRL30);
- writel(SBCTRL1_SAVEPIN_PERI_VALUE, SBCTRL31);
- writel(SBCTRL2_SAVEPIN_PERI_VALUE, SBCTRL32);
- writel(SBCTRL4_SAVEPIN_PERI_VALUE, SBCTRL34);
-
- /* base address regsiters */
- writel(0x0000bc01, SBBASE0);
- writel(0x0400bc01, SBBASE1);
- writel(0x0800bf01, SBBASE3);
-
- /* enable access to sub memory when boot swap is on */
- if (boot_is_swapped())
- sg_set_pinsel(155, 1); /* PORT24 -> XECS0 */
-
- sg_set_pinsel(156, 1); /* PORT25 -> XECS3 */
-}
+#include "../ph1-pro4/sbc_init.c"
diff --git a/arch/arm/mach-uniphier/ph1-ld4/sbc_init_3cs.c b/arch/arm/mach-uniphier/ph1-ld4/sbc_init_3cs.c
new file mode 100644
index 0000000..374a8c0
--- /dev/null
+++ b/arch/arm/mach-uniphier/ph1-ld4/sbc_init_3cs.c
@@ -0,0 +1,50 @@
+/*
+ * Copyright (C) 2011-2015 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m at jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <mach/sbc-regs.h>
+#include <mach/sg-regs.h>
+
+void sbc_init(void)
+{
+ u32 tmp;
+
+ /* system bus output enable */
+ tmp = readl(PC0CTRL);
+ tmp &= 0xfffffcff;
+ writel(tmp, PC0CTRL);
+
+ /* XECS1: sub/boot memory (boot swap = off/on) */
+ writel(SBCTRL0_SAVEPIN_MEM_VALUE, SBCTRL10);
+ writel(SBCTRL1_SAVEPIN_MEM_VALUE, SBCTRL11);
+ writel(SBCTRL2_SAVEPIN_MEM_VALUE, SBCTRL12);
+ writel(SBCTRL4_SAVEPIN_MEM_VALUE, SBCTRL14);
+
+ /* XECS0: boot/sub memory (boot swap = off/on) */
+ writel(SBCTRL0_SAVEPIN_MEM_VALUE, SBCTRL00);
+ writel(SBCTRL1_SAVEPIN_MEM_VALUE, SBCTRL01);
+ writel(SBCTRL2_SAVEPIN_MEM_VALUE, SBCTRL02);
+ writel(SBCTRL4_SAVEPIN_MEM_VALUE, SBCTRL04);
+
+ /* XECS3: peripherals */
+ writel(SBCTRL0_SAVEPIN_PERI_VALUE, SBCTRL30);
+ writel(SBCTRL1_SAVEPIN_PERI_VALUE, SBCTRL31);
+ writel(SBCTRL2_SAVEPIN_PERI_VALUE, SBCTRL32);
+ writel(SBCTRL4_SAVEPIN_PERI_VALUE, SBCTRL34);
+
+ /* base address regsiters */
+ writel(0x0000bc01, SBBASE0);
+ writel(0x0400bc01, SBBASE1);
+ writel(0x0800bf01, SBBASE3);
+
+ /* enable access to sub memory when boot swap is on */
+ if (boot_is_swapped())
+ sg_set_pinsel(155, 1); /* PORT24 -> XECS0 */
+
+ sg_set_pinsel(156, 1); /* PORT25 -> XECS3 */
+}
diff --git a/arch/arm/mach-uniphier/ph1-pro4/Makefile b/arch/arm/mach-uniphier/ph1-pro4/Makefile
index 0390506..b88525c 100644
--- a/arch/arm/mach-uniphier/ph1-pro4/Makefile
+++ b/arch/arm/mach-uniphier/ph1-pro4/Makefile
@@ -4,8 +4,10 @@
ifdef CONFIG_SPL_BUILD
obj-$(CONFIG_DEBUG_LL) += lowlevel_debug.o
-obj-y += sbc_init.o sg_init.o pll_init.o early_clkrst_init.o \
+obj-y += sg_init.o pll_init.o early_clkrst_init.o \
pll_spectrum.o umc_init.o ddrphy_init.o
+obj-$(CONFIG_PFC_MICRO_SUPPORT_CARD) += sbc_init.o
+obj-$(CONFIG_DCC_MICRO_SUPPORT_CARD) += sbc_init_3cs.o
else
obj-$(CONFIG_BOARD_EARLY_INIT_F) += pinctrl.o clkrst_init.o
obj-$(if $(CONFIG_OF_CONTROL),,y) += platdevice.o
diff --git a/arch/arm/mach-uniphier/ph1-pro4/sbc_init.c b/arch/arm/mach-uniphier/ph1-pro4/sbc_init.c
index 4cc5e75..5e75454 100644
--- a/arch/arm/mach-uniphier/ph1-pro4/sbc_init.c
+++ b/arch/arm/mach-uniphier/ph1-pro4/sbc_init.c
@@ -12,7 +12,6 @@
void sbc_init(void)
{
-#if defined(CONFIG_PFC_MICRO_SUPPORT_CARD)
/*
* Only CS1 is connected to support card.
* BKSZ[1:0] should be set to "01".
@@ -41,35 +40,4 @@ void sbc_init(void)
writel(0x0000be01, SBBASE0); /* dummy */
writel(0x0200be01, SBBASE1);
}
-#elif defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
- /* XECS0: boot/sub memory (boot swap = off/on) */
- writel(SBCTRL0_SAVEPIN_MEM_VALUE, SBCTRL00);
- writel(SBCTRL1_SAVEPIN_MEM_VALUE, SBCTRL01);
- writel(SBCTRL2_SAVEPIN_MEM_VALUE, SBCTRL02);
- writel(SBCTRL4_SAVEPIN_MEM_VALUE, SBCTRL04);
-
- /* XECS1: sub/boot memory (boot swap = off/on) */
- writel(SBCTRL0_SAVEPIN_MEM_VALUE, SBCTRL10);
- writel(SBCTRL1_SAVEPIN_MEM_VALUE, SBCTRL11);
- writel(SBCTRL2_SAVEPIN_MEM_VALUE, SBCTRL12);
- writel(SBCTRL4_SAVEPIN_MEM_VALUE, SBCTRL14);
-
- /* XECS3: peripherals */
- writel(SBCTRL0_SAVEPIN_PERI_VALUE, SBCTRL30);
- writel(SBCTRL1_SAVEPIN_PERI_VALUE, SBCTRL31);
- writel(SBCTRL2_SAVEPIN_PERI_VALUE, SBCTRL32);
- writel(SBCTRL4_SAVEPIN_PERI_VALUE, SBCTRL34);
-
- writel(0x0000bc01, SBBASE0); /* boot memory */
- writel(0x0400bc01, SBBASE1); /* sub memory */
- writel(0x0800bf01, SBBASE3); /* peripherals */
-
- /* enable access to sub memory when boot swap is on */
- if (boot_is_swapped())
- sg_set_pinsel(318, 5); /* PORT22 -> XECS0 */
-
- sg_set_pinsel(313, 5); /* PORT15 -> XECS3 */
- writel(0x00000001, SG_LOADPINCTRL);
-
-#endif /* CONFIG_XXX_MICRO_SUPPORT_CARD */
}
diff --git a/arch/arm/mach-uniphier/ph1-pro4/sbc_init_3cs.c b/arch/arm/mach-uniphier/ph1-pro4/sbc_init_3cs.c
new file mode 100644
index 0000000..67e6d82
--- /dev/null
+++ b/arch/arm/mach-uniphier/ph1-pro4/sbc_init_3cs.c
@@ -0,0 +1,43 @@
+/*
+ * Copyright (C) 2011-2015 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m at jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <mach/sbc-regs.h>
+#include <mach/sg-regs.h>
+
+void sbc_init(void)
+{
+ /* XECS0: boot/sub memory (boot swap = off/on) */
+ writel(SBCTRL0_SAVEPIN_MEM_VALUE, SBCTRL00);
+ writel(SBCTRL1_SAVEPIN_MEM_VALUE, SBCTRL01);
+ writel(SBCTRL2_SAVEPIN_MEM_VALUE, SBCTRL02);
+ writel(SBCTRL4_SAVEPIN_MEM_VALUE, SBCTRL04);
+
+ /* XECS1: sub/boot memory (boot swap = off/on) */
+ writel(SBCTRL0_SAVEPIN_MEM_VALUE, SBCTRL10);
+ writel(SBCTRL1_SAVEPIN_MEM_VALUE, SBCTRL11);
+ writel(SBCTRL2_SAVEPIN_MEM_VALUE, SBCTRL12);
+ writel(SBCTRL4_SAVEPIN_MEM_VALUE, SBCTRL14);
+
+ /* XECS3: peripherals */
+ writel(SBCTRL0_SAVEPIN_PERI_VALUE, SBCTRL30);
+ writel(SBCTRL1_SAVEPIN_PERI_VALUE, SBCTRL31);
+ writel(SBCTRL2_SAVEPIN_PERI_VALUE, SBCTRL32);
+ writel(SBCTRL4_SAVEPIN_PERI_VALUE, SBCTRL34);
+
+ writel(0x0000bc01, SBBASE0); /* boot memory */
+ writel(0x0400bc01, SBBASE1); /* sub memory */
+ writel(0x0800bf01, SBBASE3); /* peripherals */
+
+ /* enable access to sub memory when boot swap is on */
+ if (boot_is_swapped())
+ sg_set_pinsel(318, 5); /* PORT22 -> XECS0 */
+
+ sg_set_pinsel(313, 5); /* PORT15 -> XECS3 */
+ writel(0x00000001, SG_LOADPINCTRL);
+}
diff --git a/arch/arm/mach-uniphier/ph1-sld8/Makefile b/arch/arm/mach-uniphier/ph1-sld8/Makefile
index 927640a..5ce3d8a 100644
--- a/arch/arm/mach-uniphier/ph1-sld8/Makefile
+++ b/arch/arm/mach-uniphier/ph1-sld8/Makefile
@@ -4,8 +4,10 @@
ifdef CONFIG_SPL_BUILD
obj-$(CONFIG_DEBUG_LL) += lowlevel_debug.o
-obj-y += bcu_init.o sbc_init.o sg_init.o pll_init.o early_clkrst_init.o \
+obj-y += bcu_init.o sg_init.o pll_init.o early_clkrst_init.o \
pll_spectrum.o umc_init.o ddrphy_init.o
+obj-$(CONFIG_PFC_MICRO_SUPPORT_CARD) += sbc_init.o
+obj-$(CONFIG_DCC_MICRO_SUPPORT_CARD) += sbc_init_3cs.o
else
obj-$(CONFIG_BOARD_EARLY_INIT_F) += pinctrl.o clkrst_init.o
obj-$(if $(CONFIG_OF_CONTROL),,y) += platdevice.o
diff --git a/arch/arm/mach-uniphier/ph1-sld8/sbc_init.c b/arch/arm/mach-uniphier/ph1-sld8/sbc_init.c
index fdef88e..225c0d2 100644
--- a/arch/arm/mach-uniphier/ph1-sld8/sbc_init.c
+++ b/arch/arm/mach-uniphier/ph1-sld8/sbc_init.c
@@ -1,58 +1 @@
-/*
- * Copyright (C) 2011-2015 Panasonic Corporation
- * Author: Masahiro Yamada <yamada.m at jp.panasonic.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <mach/sbc-regs.h>
-#include <mach/sg-regs.h>
-
-void sbc_init(void)
-{
- u32 tmp;
-
- /* system bus output enable */
- tmp = readl(PC0CTRL);
- tmp &= 0xfffffcff;
- writel(tmp, PC0CTRL);
-
- /*
- * SBCTRL0* does not need settings because PH1-sLD8 has no support for
- * XECS0. The boot swap must be enabled to boot from the support card.
- */
-
- if (boot_is_swapped()) {
- /* XECS1 : boot memory if boot swap is on */
- writel(SBCTRL0_SAVEPIN_MEM_VALUE, SBCTRL10);
- writel(SBCTRL1_SAVEPIN_MEM_VALUE, SBCTRL11);
- writel(SBCTRL2_SAVEPIN_MEM_VALUE, SBCTRL12);
- writel(SBCTRL4_SAVEPIN_MEM_VALUE, SBCTRL14);
- }
-
- /* XECS4 : sub memory */
- writel(SBCTRL0_SAVEPIN_MEM_VALUE, SBCTRL40);
- writel(SBCTRL1_SAVEPIN_MEM_VALUE, SBCTRL41);
- writel(SBCTRL2_SAVEPIN_MEM_VALUE, SBCTRL42);
- writel(SBCTRL4_SAVEPIN_MEM_VALUE, SBCTRL44);
-
- /* XECS5 : peripherals */
- writel(SBCTRL0_SAVEPIN_PERI_VALUE, SBCTRL50);
- writel(SBCTRL1_SAVEPIN_PERI_VALUE, SBCTRL51);
- writel(SBCTRL2_SAVEPIN_PERI_VALUE, SBCTRL52);
- writel(SBCTRL4_SAVEPIN_PERI_VALUE, SBCTRL54);
-
- /* base address regsiters */
- writel(0x0000bc01, SBBASE0); /* boot memory */
- writel(0x0900bfff, SBBASE1); /* dummy */
- writel(0x0400bc01, SBBASE4); /* sub memory */
- writel(0x0800bf01, SBBASE5); /* peripherals */
-
- sg_set_pinsel(134, 16); /* XIRQ6 -> XECS4 */
- sg_set_pinsel(135, 16); /* XIRQ7 -> XECS5 */
-
- /* dummy read to assure write process */
- readl(SG_PINCTRL(0));
-}
+#include "../ph1-ld4/sbc_init.c"
diff --git a/arch/arm/mach-uniphier/ph1-sld8/sbc_init_3cs.c b/arch/arm/mach-uniphier/ph1-sld8/sbc_init_3cs.c
new file mode 100644
index 0000000..fdef88e
--- /dev/null
+++ b/arch/arm/mach-uniphier/ph1-sld8/sbc_init_3cs.c
@@ -0,0 +1,58 @@
+/*
+ * Copyright (C) 2011-2015 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m at jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <mach/sbc-regs.h>
+#include <mach/sg-regs.h>
+
+void sbc_init(void)
+{
+ u32 tmp;
+
+ /* system bus output enable */
+ tmp = readl(PC0CTRL);
+ tmp &= 0xfffffcff;
+ writel(tmp, PC0CTRL);
+
+ /*
+ * SBCTRL0* does not need settings because PH1-sLD8 has no support for
+ * XECS0. The boot swap must be enabled to boot from the support card.
+ */
+
+ if (boot_is_swapped()) {
+ /* XECS1 : boot memory if boot swap is on */
+ writel(SBCTRL0_SAVEPIN_MEM_VALUE, SBCTRL10);
+ writel(SBCTRL1_SAVEPIN_MEM_VALUE, SBCTRL11);
+ writel(SBCTRL2_SAVEPIN_MEM_VALUE, SBCTRL12);
+ writel(SBCTRL4_SAVEPIN_MEM_VALUE, SBCTRL14);
+ }
+
+ /* XECS4 : sub memory */
+ writel(SBCTRL0_SAVEPIN_MEM_VALUE, SBCTRL40);
+ writel(SBCTRL1_SAVEPIN_MEM_VALUE, SBCTRL41);
+ writel(SBCTRL2_SAVEPIN_MEM_VALUE, SBCTRL42);
+ writel(SBCTRL4_SAVEPIN_MEM_VALUE, SBCTRL44);
+
+ /* XECS5 : peripherals */
+ writel(SBCTRL0_SAVEPIN_PERI_VALUE, SBCTRL50);
+ writel(SBCTRL1_SAVEPIN_PERI_VALUE, SBCTRL51);
+ writel(SBCTRL2_SAVEPIN_PERI_VALUE, SBCTRL52);
+ writel(SBCTRL4_SAVEPIN_PERI_VALUE, SBCTRL54);
+
+ /* base address regsiters */
+ writel(0x0000bc01, SBBASE0); /* boot memory */
+ writel(0x0900bfff, SBBASE1); /* dummy */
+ writel(0x0400bc01, SBBASE4); /* sub memory */
+ writel(0x0800bf01, SBBASE5); /* peripherals */
+
+ sg_set_pinsel(134, 16); /* XIRQ6 -> XECS4 */
+ sg_set_pinsel(135, 16); /* XIRQ7 -> XECS5 */
+
+ /* dummy read to assure write process */
+ readl(SG_PINCTRL(0));
+}
--
1.9.1
More information about the U-Boot
mailing list