[U-Boot] [PATCH v5] Tegra: T210: Add QSPI driver
Jagan Teki
jteki at openedev.com
Fri Nov 6 17:39:46 CET 2015
On 6 November 2015 at 22:01, Tom Warren <TWarren at nvidia.com> wrote:
> Jagan,
>
> Ping!
>
>> -----Original Message-----
>> From: Tom Warren
>> Sent: Thursday, October 29, 2015 12:33 PM
>> To: 'Jagan Teki' <jteki at openedev.com>
>> Cc: u-boot at lists.denx.de; Stephen Warren <swarren at nvidia.com>;
>> tomcwarren3959 at gmail.com; Yen Lin <yelin at nvidia.com>
>> Subject: RE: [U-Boot] [PATCH v5] Tegra: T210: Add QSPI driver
>>
>> Jagan,
>>
>> > -----Original Message-----
>> > From: Jagan Teki [mailto:jteki at openedev.com]
>> > Sent: Thursday, October 29, 2015 10:34 AM
>> > To: Tom Warren <TWarren at nvidia.com>
>> > Cc: u-boot at lists.denx.de; Stephen Warren <swarren at nvidia.com>;
>> > tomcwarren3959 at gmail.com
>> > Subject: Re: [U-Boot] [PATCH v5] Tegra: T210: Add QSPI driver
>> >
>> > On 28 October 2015 at 21:25, Tom Warren <TWarren at nvidia.com> wrote:
>> > > Jagan,
>> > >
>> > >> -----Original Message-----
>> > >> From: Tom Warren
>> > >> Sent: Monday, October 26, 2015 1:56 PM
>> > >> To: u-boot at lists.denx.de
>> > >> Cc: Stephen Warren <swarren at nvidia.com>;
>> tomcwarren3959 at gmail.com;
>> > >> jteki at openedev.com; Yen Lin <yelin at nvidia.com>; Tom Warren
>> > >> <TWarren at nvidia.com>
>> > >> Subject: [PATCH v5] Tegra: T210: Add QSPI driver
>> > >>
>> > >> This is the normal Tegra SPI driver modified to work with the QSPI
>> > >> controller in Tegra210. It does not do 2x/4x transfers or any other
>> > >> QSPI
>> > protocol.
>> > >>
>> > >> Signed-off-by: Yen Lin <yelin at nvidia.com>
>> > >> Signed-off-by: Tom Warren <twarren at nvidia.com>
>> >
>> > Reviewed-by: Jagan Teki <jteki at openedev.com>
>> >
>> > >> ---
>> > >> Changes in v2:
>> > >> - Drop defconfig and pinmux files, this is a driver-only patch.
>> > >> - If/when pinmux tables have been updated for P2371/P2571, another
>> > >> - patch will be sent to enable the QSPI driver on those boards.
>> > >> Changes in v3:
>> > >> - removed status reg write/clear in claim_bus(), done in xfer()
>> > >> Changes in
>> > v4:
>> > >> - added timeout in wait for FIFO flush status in xfer()
>> > >> - used BIT and GENMASK macros throughout
>> > >> - minor changes in copyright message in driver and Kconfig help
>> > >> Changes in v5:
>> > >> - commented on reason for udelay before setting GO bit, as per Yen Lin.
>> > >
>> > > Can you PTAL and see if this meets all your requests? Thanks.
>> >
>> > OK with this? Can you point the dts and config patch for this driver -
>> > I couldn't find it either.
>> The intent is to only upstream the driver. The DTS already contains the QSPI
>> node (see spi at 0,70410000), and the defconfig/pinmux-config.h changes won't
>> be merged since there's no T210 board (from Nvidia) that has a SPI part on the
>> QSPI controller currently. There is a customer with their own board that needs
>> this driver upstreamed so they can pull it down into their custom U-Boot repo.
>> However, if you search the list for my original patch ('[PATCH] Tegra210: add
>> QSPI driver'), you'll see examples of the p2571 def_config/pinmux configs that
>> can be used if someone does wish to pop a SPI chip on their T210 board, etc.
I'm little concern about stale driver without have any board to use,
any possibility that T210 will be in ML - because I have removed some
in past as there is no progress on the drivers as no board's been used
for long time.
>>
>> So with that in mind, will you take this in to the SPI repo, or can I take it in via
>> the Tegra repo instead? I'm fine with either course.
>>
>> Tom
>> --
>> nvpublic
>>
>> >
>> > >
>> > > And do you want to take this in, or can I take it in via the Tegra repo?
>> > >
>> > > Tom
>> > > --
>> > > nvpublic
>> > >>
>> > >> drivers/spi/Kconfig | 7 +
>> > >> drivers/spi/Makefile | 1 +
>> > >> drivers/spi/tegra210_qspi.c | 417
>> > >> ++++++++++++++++++++++++++++++++++++++++++++
>> > >> 3 files changed, 425 insertions(+) create mode 100644
>> > >> drivers/spi/tegra210_qspi.c
>> > >>
>> > >> diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index
>> > >> 2f8cf19..95286da
>> > >> 100644
>> > >> --- a/drivers/spi/Kconfig
>> > >> +++ b/drivers/spi/Kconfig
>> > >> @@ -123,6 +123,13 @@ config TEGRA20_SLINK
>> > >> be used to access the SPI NOR flash on platforms embedding this
>> > >> nVidia Tegra20/Tegra30 IP cores.
>> > >>
>> > >> +config TEGRA210_QSPI
>> > >> + bool "nVidia Tegra210 QSPI driver"
>> > >> + help
>> > >> + Enable the Tegra Quad-SPI (QSPI) driver for T210. This driver
>> > >> + be used to access SPI chips on platforms embedding this
>> > >> + NVIDIA Tegra210 IP core.
>> > >> +
>> > >> config XILINX_SPI
>> > >> bool "Xilinx SPI driver"
>> > >> help
>> > >> diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index
>> > >> de241be..209a41e
>> > >> 100644
>> > >> --- a/drivers/spi/Makefile
>> > >> +++ b/drivers/spi/Makefile
>> > >> @@ -46,6 +46,7 @@ obj-$(CONFIG_SH_QSPI) += sh_qspi.o
>> > >> obj-$(CONFIG_TEGRA114_SPI) += tegra114_spi.o
>> > >> obj-$(CONFIG_TEGRA20_SFLASH) += tegra20_sflash.o
>> > >> obj-$(CONFIG_TEGRA20_SLINK) += tegra20_slink.o
>> > >> +obj-$(CONFIG_TEGRA210_QSPI) += tegra210_qspi.o
>> > >> obj-$(CONFIG_TI_QSPI) += ti_qspi.o
>> > >> obj-$(CONFIG_XILINX_SPI) += xilinx_spi.o
>> > >> obj-$(CONFIG_ZYNQ_SPI) += zynq_spi.o diff --git
>> > >> a/drivers/spi/tegra210_qspi.c b/drivers/spi/tegra210_qspi.c new
>> > >> file mode 100644 index 0000000..6bbbe93
>> > >> --- /dev/null
>> > >> +++ b/drivers/spi/tegra210_qspi.c
>> > >> @@ -0,0 +1,417 @@
>> > >> +/*
>> > >> + * NVIDIA Tegra210 QSPI controller driver
>> > >> + *
>> > >> + * (C) Copyright 2015 NVIDIA Corporation <www.nvidia.com>
>> > >> + *
>> > >> + * SPDX-License-Identifier: GPL-2.0+
>> > >> + */
>> > >> +
>> > >> +#include <common.h>
>> > >> +#include <dm.h>
>> > >> +#include <asm/io.h>
>> > >> +#include <asm/arch/clock.h>
>> > >> +#include <asm/arch-tegra/clk_rst.h> #include <spi.h> #include
>> > >> +<fdtdec.h> #include "tegra_spi.h"
>> > >> +
>> > >> +DECLARE_GLOBAL_DATA_PTR;
>> > >> +
>> > >> +/* COMMAND1 */
>> > >> +#define QSPI_CMD1_GO BIT(31)
>> > >> +#define QSPI_CMD1_M_S BIT(30)
>> > >> +#define QSPI_CMD1_MODE_MASK GENMASK(1,0)
>> > >> +#define QSPI_CMD1_MODE_SHIFT 28
>> > >> +#define QSPI_CMD1_CS_SEL_MASK GENMASK(1,0)
>> > >> +#define QSPI_CMD1_CS_SEL_SHIFT 26
>> > >> +#define QSPI_CMD1_CS_POL_INACTIVE0 BIT(22)
>> > >> +#define QSPI_CMD1_CS_SW_HW BIT(21)
>> > >> +#define QSPI_CMD1_CS_SW_VAL BIT(20)
>> > >> +#define QSPI_CMD1_IDLE_SDA_MASK GENMASK(1,0)
>> > >> +#define QSPI_CMD1_IDLE_SDA_SHIFT 18
>> > >> +#define QSPI_CMD1_BIDIR BIT(17)
>> > >> +#define QSPI_CMD1_LSBI_FE BIT(16)
>> > >> +#define QSPI_CMD1_LSBY_FE BIT(15)
>> > >> +#define QSPI_CMD1_BOTH_EN_BIT BIT(14)
>> > >> +#define QSPI_CMD1_BOTH_EN_BYTE BIT(13)
>> > >> +#define QSPI_CMD1_RX_EN BIT(12)
>> > >> +#define QSPI_CMD1_TX_EN BIT(11)
>> > >> +#define QSPI_CMD1_PACKED BIT(5)
>> > >> +#define QSPI_CMD1_BITLEN_MASK GENMASK(4,0)
>> > >> +#define QSPI_CMD1_BITLEN_SHIFT 0
>> > >> +
>> > >> +/* COMMAND2 */
>> > >> +#define QSPI_CMD2_TX_CLK_TAP_DELAY BIT(6)
>> > >> +#define QSPI_CMD2_TX_CLK_TAP_DELAY_MASK GENMASK(11,6)
>> > >> +#define QSPI_CMD2_RX_CLK_TAP_DELAY BIT(0)
>> > >> +#define QSPI_CMD2_RX_CLK_TAP_DELAY_MASK GENMASK(5,0)
>> > >> +
>> > >> +/* TRANSFER STATUS */
>> > >> +#define QSPI_XFER_STS_RDY BIT(30)
>> > >> +
>> > >> +/* FIFO STATUS */
>> > >> +#define QSPI_FIFO_STS_CS_INACTIVE BIT(31)
>> > >> +#define QSPI_FIFO_STS_FRAME_END BIT(30)
>> > >> +#define QSPI_FIFO_STS_RX_FIFO_FLUSH BIT(15) #define
>> > >> +QSPI_FIFO_STS_TX_FIFO_FLUSH BIT(14)
>> > >> +#define QSPI_FIFO_STS_ERR BIT(8)
>> > >> +#define QSPI_FIFO_STS_TX_FIFO_OVF BIT(7)
>> > >> +#define QSPI_FIFO_STS_TX_FIFO_UNR BIT(6)
>> > >> +#define QSPI_FIFO_STS_RX_FIFO_OVF BIT(5)
>> > >> +#define QSPI_FIFO_STS_RX_FIFO_UNR BIT(4)
>> > >> +#define QSPI_FIFO_STS_TX_FIFO_FULL BIT(3)
>> > >> +#define QSPI_FIFO_STS_TX_FIFO_EMPTY BIT(2)
>> > >> +#define QSPI_FIFO_STS_RX_FIFO_FULL BIT(1)
>> > >> +#define QSPI_FIFO_STS_RX_FIFO_EMPTY BIT(0)
>> > >> +
>> > >> +#define QSPI_TIMEOUT 1000
>> > >> +
>> > >> +struct qspi_regs {
>> > >> + u32 command1; /* 000:QSPI_COMMAND1 register */
>> > >> + u32 command2; /* 004:QSPI_COMMAND2 register */
>> > >> + u32 timing1; /* 008:QSPI_CS_TIM1 register */
>> > >> + u32 timing2; /* 00c:QSPI_CS_TIM2 register */
>> > >> + u32 xfer_status;/* 010:QSPI_TRANS_STATUS register */
>> > >> + u32 fifo_status;/* 014:QSPI_FIFO_STATUS register */
>> > >> + u32 tx_data; /* 018:QSPI_TX_DATA register */
>> > >> + u32 rx_data; /* 01c:QSPI_RX_DATA register */
>> > >> + u32 dma_ctl; /* 020:QSPI_DMA_CTL register */
>> > >> + u32 dma_blk; /* 024:QSPI_DMA_BLK register */
>> > >> + u32 rsvd[56]; /* 028-107 reserved */
>> > >> + u32 tx_fifo; /* 108:QSPI_FIFO1 register */
>> > >> + u32 rsvd2[31]; /* 10c-187 reserved */
>> > >> + u32 rx_fifo; /* 188:QSPI_FIFO2 register */
>> > >> + u32 spare_ctl; /* 18c:QSPI_SPARE_CTRL register */ };
>> > >> +
>> > >> +struct tegra210_qspi_priv {
>> > >> + struct qspi_regs *regs;
>> > >> + unsigned int freq;
>> > >> + unsigned int mode;
>> > >> + int periph_id;
>> > >> + int valid;
>> > >> + int last_transaction_us;
>> > >> +};
>> > >> +
>> > >> +static int tegra210_qspi_ofdata_to_platdata(struct udevice *bus) {
>> > >> + struct tegra_spi_platdata *plat = bus->platdata;
>> > >> + const void *blob = gd->fdt_blob;
>> > >> + int node = bus->of_offset;
>> > >> +
>> > >> + plat->base = dev_get_addr(bus);
>> > >> + plat->periph_id = clock_decode_periph_id(blob, node);
>> > >> +
>> > >> + if (plat->periph_id == PERIPH_ID_NONE) {
>> > >> + debug("%s: could not decode periph id %d\n", __func__,
>> > >> + plat->periph_id);
>> > >> + return -FDT_ERR_NOTFOUND;
>> > >> + }
>> > >> +
>> > >> + /* Use 500KHz as a suitable default */
>> > >> + plat->frequency = fdtdec_get_int(blob, node, "spi-max-frequency",
>> > >> + 500000);
>> > >> + plat->deactivate_delay_us = fdtdec_get_int(blob, node,
>> > >> + "spi-deactivate-delay", 0);
>> > >> + debug("%s: base=%#08lx, periph_id=%d, max-frequency=%d,
>> > >> deactivate_delay=%d\n",
>> > >> + __func__, plat->base, plat->periph_id, plat->frequency,
>> > >> + plat->deactivate_delay_us);
>> > >> +
>> > >> + return 0;
>> > >> +}
>> > >> +
>> > >> +static int tegra210_qspi_probe(struct udevice *bus) {
>> > >> + struct tegra_spi_platdata *plat = dev_get_platdata(bus);
>> > >> + struct tegra210_qspi_priv *priv = dev_get_priv(bus);
>> > >> +
>> > >> + priv->regs = (struct qspi_regs *)plat->base;
>> > >> +
>> > >> + priv->last_transaction_us = timer_get_us();
>> > >> + priv->freq = plat->frequency;
>> > >> + priv->periph_id = plat->periph_id;
>> > >> +
>> > >> + return 0;
>> > >> +}
>> > >> +
>> > >> +static int tegra210_qspi_claim_bus(struct udevice *bus) {
>> > >> + struct tegra210_qspi_priv *priv = dev_get_priv(bus);
>> > >> + struct qspi_regs *regs = priv->regs;
>> > >> +
>> > >> + /* Change SPI clock to correct frequency, PLLP_OUT0 source */
>> > >> + clock_start_periph_pll(priv->periph_id, CLOCK_ID_PERIPH,
>> > >> + priv->freq);
>> > >> +
>> > >> + debug("%s: FIFO STATUS = %08x\n", __func__,
>> > >> +readl(®s->fifo_status));
>> > >> +
>> > >> + /* Set master mode and sw controlled CS */
>> > >> + setbits_le32(®s->command1, QSPI_CMD1_M_S |
>> > >> QSPI_CMD1_CS_SW_HW |
>> > >> + (priv->mode << QSPI_CMD1_MODE_SHIFT));
>> > >> + debug("%s: COMMAND1 = %08x\n", __func__, readl(®s-
>> > >> >command1));
>> > >> +
>> > >> + return 0;
>> > >> +}
>> > >> +
>> > >> +/**
>> > >> + * Activate the CS by driving it LOW
>> > >> + *
>> > >> + * @param slave Pointer to spi_slave to which controller has to
>> > >> + * communicate with
>> > >> + */
>> > >> +static void spi_cs_activate(struct udevice *dev) {
>> > >> + struct udevice *bus = dev->parent;
>> > >> + struct tegra_spi_platdata *pdata = dev_get_platdata(bus);
>> > >> + struct tegra210_qspi_priv *priv = dev_get_priv(bus);
>> > >> +
>> > >> + /* If it's too soon to do another transaction, wait */
>> > >> + if (pdata->deactivate_delay_us &&
>> > >> + priv->last_transaction_us) {
>> > >> + ulong delay_us; /* The delay completed so far */
>> > >> + delay_us = timer_get_us() - priv->last_transaction_us;
>> > >> + if (delay_us < pdata->deactivate_delay_us)
>> > >> + udelay(pdata->deactivate_delay_us - delay_us);
>> > >> + }
>> > >> +
>> > >> + clrbits_le32(&priv->regs->command1, QSPI_CMD1_CS_SW_VAL); }
>> > >> +
>> > >> +/**
>> > >> + * Deactivate the CS by driving it HIGH
>> > >> + *
>> > >> + * @param slave Pointer to spi_slave to which controller has to
>> > >> + * communicate with
>> > >> + */
>> > >> +static void spi_cs_deactivate(struct udevice *dev) {
>> > >> + struct udevice *bus = dev->parent;
>> > >> + struct tegra_spi_platdata *pdata = dev_get_platdata(bus);
>> > >> + struct tegra210_qspi_priv *priv = dev_get_priv(bus);
>> > >> +
>> > >> + setbits_le32(&priv->regs->command1, QSPI_CMD1_CS_SW_VAL);
>> > >> +
>> > >> + /* Remember time of this transaction so we can honour the bus
>> > >> + delay
>> > >> */
>> > >> + if (pdata->deactivate_delay_us)
>> > >> + priv->last_transaction_us = timer_get_us();
>> > >> +
>> > >> + debug("Deactivate CS, bus '%s'\n", bus->name); }
>> > >> +
>> > >> +static int tegra210_qspi_xfer(struct udevice *dev, unsigned int bitlen,
>> > >> + const void *data_out, void *data_in,
>> > >> + unsigned long flags) {
>> > >> + struct udevice *bus = dev->parent;
>> > >> + struct tegra210_qspi_priv *priv = dev_get_priv(bus);
>> > >> + struct qspi_regs *regs = priv->regs;
>> > >> + u32 reg, tmpdout, tmpdin = 0;
>> > >> + const u8 *dout = data_out;
>> > >> + u8 *din = data_in;
>> > >> + int num_bytes, tm, ret;
>> > >> +
>> > >> + debug("%s: slave %u:%u dout %p din %p bitlen %u\n",
>> > >> + __func__, bus->seq, spi_chip_select(dev), dout, din, bitlen);
>> > >> + if (bitlen % 8)
>> > >> + return -1;
>> > >> + num_bytes = bitlen / 8;
>> > >> +
>> > >> + ret = 0;
>> > >> +
>> > >> + /* clear all error status bits */
>> > >> + reg = readl(®s->fifo_status);
>> > >> + writel(reg, ®s->fifo_status);
>> > >> +
>> > >> + /* flush RX/TX FIFOs */
>> > >> + setbits_le32(®s->fifo_status,
>> > >> + (QSPI_FIFO_STS_RX_FIFO_FLUSH |
>> > >> + QSPI_FIFO_STS_TX_FIFO_FLUSH));
>> > >> +
>> > >> + tm = QSPI_TIMEOUT;
>> > >> + while ((tm && readl(®s->fifo_status) &
>> > >> + (QSPI_FIFO_STS_RX_FIFO_FLUSH |
>> > >> + QSPI_FIFO_STS_TX_FIFO_FLUSH))) {
>> > >> + tm--;
>> > >> + udelay(1);
>> > >> + }
>> > >> +
>> > >> + if (!tm) {
>> > >> + printf("%s: timeout during QSPI FIFO flush!\n",
>> > >> + __func__);
>> > >> + return -1;
>> > >> + }
>> > >> +
>> > >> + /*
>> > >> + * Notes:
>> > >> + * 1. don't set LSBY_FE, so no need to swap bytes from/to TX/RX
>> FIFOs;
>> > >> + * 2. don't set RX_EN and TX_EN yet.
>> > >> + * (SW needs to make sure that while programming the blk_size,
>> > >> + * tx_en and rx_en bits must be zero)
>> > >> + * [TODO] I (Yen Lin) have problems when both RX/TX EN bits are
>> > >> set
>> > >> + * i.e., both dout and din are not NULL.
>> > >> + */
>> > >> + clrsetbits_le32(®s->command1,
>> > >> + (QSPI_CMD1_LSBI_FE | QSPI_CMD1_LSBY_FE |
>> > >> + QSPI_CMD1_RX_EN | QSPI_CMD1_TX_EN),
>> > >> + (spi_chip_select(dev) <<
>> > >> + QSPI_CMD1_CS_SEL_SHIFT));
>> > >> +
>> > >> + /* set xfer size to 1 block (32 bits) */
>> > >> + writel(0, ®s->dma_blk);
>> > >> +
>> > >> + if (flags & SPI_XFER_BEGIN)
>> > >> + spi_cs_activate(dev);
>> > >> +
>> > >> + /* handle data in 32-bit chunks */
>> > >> + while (num_bytes > 0) {
>> > >> + int bytes;
>> > >> +
>> > >> + tmpdout = 0;
>> > >> + bytes = (num_bytes > 4) ? 4 : num_bytes;
>> > >> +
>> > >> + if (dout != NULL) {
>> > >> + memcpy((void *)&tmpdout, (void *)dout, bytes);
>> > >> + dout += bytes;
>> > >> + num_bytes -= bytes;
>> > >> + writel(tmpdout, ®s->tx_fifo);
>> > >> + setbits_le32(®s->command1, QSPI_CMD1_TX_EN);
>> > >> + }
>> > >> +
>> > >> + if (din != NULL)
>> > >> + setbits_le32(®s->command1,
>> > >> + QSPI_CMD1_RX_EN);
>> > >> +
>> > >> + /* clear ready bit */
>> > >> + setbits_le32(®s->xfer_status, QSPI_XFER_STS_RDY);
>> > >> +
>> > >> + clrsetbits_le32(®s->command1,
>> > >> + QSPI_CMD1_BITLEN_MASK <<
>> > >> QSPI_CMD1_BITLEN_SHIFT,
>> > >> + (bytes * 8 - 1) <<
>> > >> + QSPI_CMD1_BITLEN_SHIFT);
>> > >> +
>> > >> + /* Need to stabilize other reg bits before GO bit set.
>> > >> + * As per the TRM:
>> > >> + * "For successful operation at various freq combinations,
>> > >> + * a minimum of 4-5 spi_clk cycle delay might be required
>> > >> + * before enabling the PIO or DMA bits. The worst case delay
>> > >> + * calculation can be done considering slowest qspi_clk as
>> > >> + * 1MHz. Based on that 1us delay should be enough before
>> > >> + * enabling PIO or DMA." Padded another 1us for safety.
>> > >> + */
>> > >> + udelay(2);
>> > >> + setbits_le32(®s->command1, QSPI_CMD1_GO);
>> > >> + udelay(1);
>> > >> +
>> > >> + /*
>> > >> + * Wait for SPI transmit FIFO to empty, or to time out.
>> > >> + * The RX FIFO status will be read and cleared last
>> > >> + */
>> > >> + for (tm = 0; tm < QSPI_TIMEOUT; ++tm) {
>> > >> + u32 fifo_status, xfer_status;
>> > >> +
>> > >> + xfer_status = readl(®s->xfer_status);
>> > >> + if (!(xfer_status & QSPI_XFER_STS_RDY))
>> > >> + continue;
>> > >> +
>> > >> + fifo_status = readl(®s->fifo_status);
>> > >> + if (fifo_status & QSPI_FIFO_STS_ERR) {
>> > >> + debug("%s: got a fifo error: ", __func__);
>> > >> + if (fifo_status & QSPI_FIFO_STS_TX_FIFO_OVF)
>> > >> + debug("tx FIFO overflow ");
>> > >> + if (fifo_status & QSPI_FIFO_STS_TX_FIFO_UNR)
>> > >> + debug("tx FIFO underrun ");
>> > >> + if (fifo_status & QSPI_FIFO_STS_RX_FIFO_OVF)
>> > >> + debug("rx FIFO overflow ");
>> > >> + if (fifo_status & QSPI_FIFO_STS_RX_FIFO_UNR)
>> > >> + debug("rx FIFO underrun ");
>> > >> + if (fifo_status & QSPI_FIFO_STS_TX_FIFO_FULL)
>> > >> + debug("tx FIFO full ");
>> > >> + if (fifo_status &
>> > >> QSPI_FIFO_STS_TX_FIFO_EMPTY)
>> > >> + debug("tx FIFO empty ");
>> > >> + if (fifo_status &
>> > >> QSPI_FIFO_STS_RX_FIFO_FULL)
>> > >> + debug("rx FIFO full ");
>> > >> + if (fifo_status &
>> > >> QSPI_FIFO_STS_RX_FIFO_EMPTY)
>> > >> + debug("rx FIFO empty ");
>> > >> + debug("\n");
>> > >> + break;
>> > >> + }
>> > >> +
>> > >> + if (!(fifo_status & QSPI_FIFO_STS_RX_FIFO_EMPTY)) {
>> > >> + tmpdin = readl(®s->rx_fifo);
>> > >> + if (din != NULL) {
>> > >> + memcpy(din, &tmpdin, bytes);
>> > >> + din += bytes;
>> > >> + num_bytes -= bytes;
>> > >> + }
>> > >> + }
>> > >> + break;
>> > >> + }
>> > >> +
>> > >> + if (tm >= QSPI_TIMEOUT)
>> > >> + ret = tm;
>> > >> +
>> > >> + /* clear ACK RDY, etc. bits */
>> > >> + writel(readl(®s->fifo_status), ®s->fifo_status);
>> > >> + }
>> > >> +
>> > >> + if (flags & SPI_XFER_END)
>> > >> + spi_cs_deactivate(dev);
>> > >> +
>> > >> + debug("%s: transfer ended. Value=%08x, fifo_status = %08x\n",
>> > >> + __func__, tmpdin, readl(®s->fifo_status));
>> > >> +
>> > >> + if (ret) {
>> > >> + printf("%s: timeout during SPI transfer, tm %d\n",
>> > >> + __func__, ret);
>> > >> + return -1;
>> > >> + }
>> > >> +
>> > >> + return ret;
>> > >> +}
>> > >> +
>> > >> +static int tegra210_qspi_set_speed(struct udevice *bus, uint speed) {
>> > >> + struct tegra_spi_platdata *plat = bus->platdata;
>> > >> + struct tegra210_qspi_priv *priv = dev_get_priv(bus);
>> > >> +
>> > >> + if (speed > plat->frequency)
>> > >> + speed = plat->frequency;
>> > >> + priv->freq = speed;
>> > >> + debug("%s: regs=%p, speed=%d\n", __func__, priv->regs,
>> > >> + priv->freq);
>> > >> +
>> > >> + return 0;
>> > >> +}
>> > >> +
>> > >> +static int tegra210_qspi_set_mode(struct udevice *bus, uint mode) {
>> > >> + struct tegra210_qspi_priv *priv = dev_get_priv(bus);
>> > >> +
>> > >> + priv->mode = mode;
>> > >> + debug("%s: regs=%p, mode=%d\n", __func__, priv->regs,
>> > >> + priv->mode);
>> > >> +
>> > >> + return 0;
>> > >> +}
>> > >> +
>> > >> +static const struct dm_spi_ops tegra210_qspi_ops = {
>> > >> + .claim_bus = tegra210_qspi_claim_bus,
>> > >> + .xfer = tegra210_qspi_xfer,
>> > >> + .set_speed = tegra210_qspi_set_speed,
>> > >> + .set_mode = tegra210_qspi_set_mode,
>> > >> + /*
>> > >> + * cs_info is not needed, since we require all chip selects to be
>> > >> + * in the device tree explicitly
>> > >> + */
>> > >> +};
>> > >> +
>> > >> +static const struct udevice_id tegra210_qspi_ids[] = {
>> > >> + { .compatible = "nvidia,tegra210-qspi" },
>> > >> + { }
>> > >> +};
>> > >> +
>> > >> +U_BOOT_DRIVER(tegra210_qspi) = {
>> > >> + .name = "tegra210-qspi",
>> > >> + .id = UCLASS_SPI,
>> > >> + .of_match = tegra210_qspi_ids,
>> > >> + .ops = &tegra210_qspi_ops,
>> > >> + .ofdata_to_platdata = tegra210_qspi_ofdata_to_platdata,
>> > >> + .platdata_auto_alloc_size = sizeof(struct tegra_spi_platdata),
>> > >> + .priv_auto_alloc_size = sizeof(struct tegra210_qspi_priv),
>> > >> + .per_child_auto_alloc_size = sizeof(struct spi_slave),
>> > >> + .probe = tegra210_qspi_probe, };
>> > >> --
>> > >> 1.8.2.1.610.g562af5b
>> >
>> > thanks!
>> > --
>> > Jagan | openedev.
> --
> nvpublic
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
--
Jagan | openedev.
More information about the U-Boot
mailing list