[U-Boot] [PATCH] arm: socfpga: Add support for the Terasic DE-0 Atlas board

Chin Liang See clsee at altera.com
Tue Sep 1 10:45:56 CEST 2015


On Tue, 2015-09-01 at 10:30 +0200, marex at denx.de wrote:
> On Tuesday, September 01, 2015 at 06:54:14 AM, Chin Liang See wrote:
> > On Mon, 2015-08-31 at 14:57 -0500, dinguyen at opensource.altera.com wrote:
> > > From: Dinh Nguyen <dinguyen at opensource.altera.com>
> > > 
> > > Add support for the Terasic DE0-Nano/Atlas-SoC Kit, which is a CycloneV
> > > based board. The board can boot from SD/MMC. Ethernet is a bit different
> > > because it has a KSZ9031 PHY, so for now, ethernet doesn't quite work
> > > yet, as a few patches are needed to support the PHY.
> > > 
> > > Signed-off-by: Dinh Nguyen <dinguyen at opensource.altera.com>
> > > ---
> > > Hi Marek,
> > > 
> > > This patch is based on your u-boot-socfpga/wip/boards branch.
> > > 
> > > Thanks,
> > > Dinh
> > > ---
> > > 
> > >  arch/arm/dts/Makefile                        |   1 +
> > >  arch/arm/dts/socfpga_cyclone5_de0_sockit.dts |  61 +++
> > >  arch/arm/mach-socfpga/Kconfig                |   7 +
> > >  board/terasic/de0/MAINTAINERS                |   5 +
> > >  board/terasic/de0/Makefile                   |   9 +
> > >  board/terasic/de0/qts/iocsr_config.h         | 658
> > >  +++++++++++++++++++++++++++ board/terasic/de0/qts/pinmux_config.h      
> > >   | 220 +++++++++
> > >  board/terasic/de0/qts/pll_config.h           |  85 ++++
> > >  board/terasic/de0/qts/sdram_config.h         | 342 ++++++++++++++
> > >  board/terasic/de0/socfpga.c                  |  22 +
> > >  configs/socfpga_de0_defconfig                |  21 +
> > >  include/configs/socfpga_de0.h                |  88 ++++
> > >  12 files changed, 1519 insertions(+)
> > >  create mode 100644 arch/arm/dts/socfpga_cyclone5_de0_sockit.dts
> > >  create mode 100644 board/terasic/de0/MAINTAINERS
> > >  create mode 100644 board/terasic/de0/Makefile
> > >  create mode 100644 board/terasic/de0/qts/iocsr_config.h
> > >  create mode 100644 board/terasic/de0/qts/pinmux_config.h
> > >  create mode 100644 board/terasic/de0/qts/pll_config.h
> > >  create mode 100644 board/terasic/de0/qts/sdram_config.h
> > >  create mode 100644 board/terasic/de0/socfpga.c
> > >  create mode 100644 configs/socfpga_de0_defconfig
> > >  create mode 100644 include/configs/socfpga_de0.h
> > > 
> > > diff --git a/include/configs/socfpga_de0.h
> > > b/include/configs/socfpga_de0.h new file mode 100644
> > > index 0000000..47e18ba
> > > --- /dev/null
> > > +++ b/include/configs/socfpga_de0.h
> > > @@ -0,0 +1,88 @@
> > > +/*
> > > + * Copyright (C) 2015 Marek Vasut <marex at denx.de>
> > > + *
> > > + * SPDX-License-Identifier:	GPL-2.0+
> > > + */
> > > +#ifndef __CONFIG_TERASIC_DE0_H__
> > > +#define __CONFIG_TERASIC_DE0_H__
> > > +
> > > +#include <asm/arch/socfpga_base_addrs.h>
> > > +
> > > +/* U-Boot Commands */
> > > +#define CONFIG_SYS_NO_FLASH
> > > +#define CONFIG_DOS_PARTITION
> > > +#define CONFIG_FAT_WRITE
> > > +#define CONFIG_HW_WATCHDOG
> > > +
> > > +#define CONFIG_CMD_ASKENV
> > > +#define CONFIG_CMD_BOOTZ
> > > +#define CONFIG_CMD_CACHE
> > > +#define CONFIG_CMD_DFU
> > > +#define CONFIG_CMD_DHCP
> > > +#define CONFIG_CMD_EXT4
> > > +#define CONFIG_CMD_EXT4_WRITE
> > > +#define CONFIG_CMD_FAT
> > > +#define CONFIG_CMD_FS_GENERIC
> > > +#define CONFIG_CMD_GPIO
> > > +#define CONFIG_CMD_GREPENV
> > > +#define CONFIG_CMD_MII
> > > +#define CONFIG_CMD_MMC
> > > +#define CONFIG_CMD_PING
> > > +#define CONFIG_CMD_USB
> > > +#define CONFIG_CMD_USB_MASS_STORAGE
> > > +
> > > +/* Memory configurations */
> > > +#define PHYS_SDRAM_1_SIZE		0x40000000	/* 1GiB */
> > > +
> > > +/* Booting Linux */
> > > +#define CONFIG_BOOTDELAY	3
> > > +#define CONFIG_BOOTFILE		"fitImage"
> > 
> > Wonder this should be zImage as the mmcload still using zImage?
> 
> Or maybe the mmcload should be fixed instead ; fitImage is preferred.

Yup, I agreed that as we can enable checksum even its zimage.

Thanks
Chin Liang




More information about the U-Boot mailing list