[U-Boot] [PATCH 1/2] mmc: dw_mmc: Increase timeout to 20 seconds

Marek Vasut marex at denx.de
Tue Sep 1 13:33:13 CEST 2015


On Tuesday, September 01, 2015 at 01:19:09 PM, Lukasz Majewski wrote:
> Hi Marek,

Hi!

> > On Saturday, August 29, 2015 at 06:38:48 PM, Lukasz Majewski wrote:
> > > Hi Marek,
> > 
> > Hi Lukasz,
> > 
> > > > On Saturday, August 29, 2015 at 01:55:36 PM, Lukasz Majewski
> > > > 
> > > > wrote:
> > > > > On Fri, 28 Aug 2015 23:55:17 +0200
> > > > 
> > > > Hi!
> > > > 
> > > > > Marek Vasut <marex at denx.de> wrote:
> > > > > > On Friday, August 28, 2015 at 03:50:20 PM, Lukasz Majewski
> > > > > > 
> > > > > > wrote:
> > > > > > > The commit: d9dbb97be0e4a550457aec5f11afefb446169c90
> > > > > > > "mmc: dw_mmc: Zap endless timeout" removed endless loop
> > > > > > > waiting for end of dw mmc transfer.
> > > > > > > 
> > > > > > > For some workloads - dfu test @ Odroid XU3 (sending 8MiB
> > > > > > > file) - and SD cards (e.g. MicroSD Kingston 4GiB, Adata
> > > > > > > 4GiB) the default timeout is to short.
> > > > > > > 
> > > > > > > The new value - 20 seconds - takes into account the
> > > > > > > situation when SD card triggers internal clean up. Such
> > > > > > > process may take more than 10 seconds on some cards.
> > > > > > 
> > > > > > What happens if you pull the SD card out of the slot during
> > > > > > such a process?
> > > > > 
> > > > > Then we would wait 20 seconds :-) to proceed.
> > > > 
> > > > Oops, I think I was not clear here. I was wondering what happens
> > > > to the card if you yank it out of the slot whole it's performing
> > > > it's internal cleanup or whatever. Is it possible that the card
> > > > suffers data corruption, effectively trashing user data ?
> > > 
> > > I think that only the card manufacturer may reveal what can happen
> > > with the card (what policy have been implemented in their FW).
> > > 
> > > I guess that you may lost data in such case.
> > 
> > Uuuurgh, that's seriously shitty.
> > 
> > > > Is this behavior
> > > > specific to Samsung SD cards ?
> > > 
> > > I've experienced the problem with Kingston (brand new one) and Adata
> > > MicroSD HC (4GiB) cards.
> > 
> > I had bad previous experience with Kingston too.
> > 
> > > > > To be clear - the mentioned patch introduced regression.
> > > > 
> > > > That's a bug, not a regression, but anyway,
> > > > that's not the point. I do
> > > > agree with you that we do have a problem and I'm inclined to Ack
> > > > this patch, I'd like to understand what the real implications of
> > > > such a behavior of these cards are.
> > > > 
> > > > > It works for
> > > > > small files on a commonly available SD cards (like 4 GiB
> > > > > Kingston/Adata).
> > > > > 
> > > > > When I ran DFU tests I've discovered that there is a problem
> > > > > with storing 8MiB file (dat_8M.img).
> > > > > 
> > > > > Even worse - when one wants to store Image.itb file (which
> > > > > might be 4-6 MiB) it sometimes works and sometimes not.
> > > > > Nightmare for debugging.
> > > > 
> > > > Ew, that's one crappy card you have there. I'm reading the SD card
> > > > "Physical Layer Simplified Specification Version
> > > > 4.10" (part1_410.pdf) section 4.6.2.2 and it states that for SDHC
> > > > cards, the write operation should take at most 250mS, for SDXC
> > > > it's 500mS. Could it be that your card is violating the spec ?
> 
> The "timeout" error is for situation when you issue write command
> (either single or multiple block) and you don't receive any response
> from the card.
> 
> In our case we use multiblock transfer (CMD25) with either set number
> of block to transfer (CMD23) or explicit end of transmission (CMD12).
> 
> Let's consider the second case.
> 
> We setup data and issue CMD25. Then we check the CMD25 status (if we
> don't receive reply in 250 ms we would get timeout error).
> Afterwards data from buffer is transmitted to the card and flashed.
> This operation may take long time. During this process you can issue
> CMD13 (SEND_STATUS) to receive information about card state ([*] 4.10. -
> page 85).

Maybe we should implement such polling through CMD13 then ? But, this
should be a matter for next MW, this MW we should go with increasing
the timeout to some 20 or 30 second. What do you think ?

> Two notable fields of [*] to check are READY_FOR_DATA and CURRENT_STATE.
> Those two state what is the SD Card controller situation.
> 
> Then, you end the transfer with CMD12, which also provides some status
> information from the SDCard (like "prg"|"rcv", etc).
> 
> If you want to issue next command you must check READY_FOR_DATA and
> CURRENT_STATE. In the case of internal SD card controller operation you
> would not get READY_FOR_DATA until it ends.
> 
> > > I'll look into the spec and then comment :-).
> > > 
> > > For my boards the time was 1.2 seconds for storing 8 MiB file.
> > 
> > OK, but that's weird. The transfer should always be up to 512B long
> > and not any longer, unless it's a multiblock transfer.
> 
> It is a multi block transfer.

[...]


More information about the U-Boot mailing list