[U-Boot] [PATCH v2 1/2] usb: zynqmp: Add XHCI driver support

[Marek Vasut]

On Tuesday, September 01, 2015 at 12:31:02 PM, Siva Durga Prasad Paladugu wrote:
> Added USB XHCI driver support for zynqmp.
> 
> Signed-off-by: Siva Durga Prasad Paladugu <sivadur at xilinx.com>

Hi, looks almost good, a few minor nits though ...

[...]

> +unsigned long ctr_addr[] = {ZYNQMP_USB0_XHCI_BASEADDR,

static const void __iomem *ctl_addr[]

> +			    ZYNQMP_USB1_XHCI_BASEADDR};

I guess you can define something like CONFIG_ZYNQMP_XHCI_LIST { address ... }
in your board config file and then use static const unsigned long ctl_addr[] =
CONFIG_ZYNQMP... ; This will cover board which only use one controller.
The ideal way would be to obtain these information from DT though.

> +__weak int __board_usb_init(int index, enum usb_init_type init)
> +{
> +	return 0;
> +}
> +
> +void usb_phy_reset(struct dwc3 *dwc3_reg)
> +{
> +	/* Assert USB3 PHY reset */
> +	setbits_le32(&dwc3_reg->g_usb3pipectl[0], DWC3_GUSB3PIPECTL_PHYSOFTRST);
> +
> +	/* Assert USB2 PHY reset */
> +	setbits_le32(&dwc3_reg->g_usb2phycfg, DWC3_GUSB2PHYCFG_PHYSOFTRST);
> +
> +	mdelay(200);

That's some lazy crappy controller. Is this long delay needed ?

> +	/* Clear USB3 PHY reset */
> +	clrbits_le32(&dwc3_reg->g_usb3pipectl[0], DWC3_GUSB3PIPECTL_PHYSOFTRST);
> +
> +	/* Clear USB2 PHY reset */
> +	clrbits_le32(&dwc3_reg->g_usb2phycfg, DWC3_GUSB2PHYCFG_PHYSOFTRST);
> +}
> +
> +static int zynqmp_xhci_core_init(struct zynqmp_xhci *zynqmp_xhci)
> +{
> +	int ret = 0;
> +
> +	ret = dwc3_core_init(zynqmp_xhci->dwc3_reg);
> +	if (ret) {
> +		debug("%s:failed to initialize core\n", __func__);
> +		return ret;
> +	}
> +
> +	/* We are hard-coding DWC3 core to Host Mode */
> +	dwc3_set_mode(zynqmp_xhci->dwc3_reg, DWC3_GCTL_PRTCAP_HOST);
> +
> +	return ret;
> +}
> +
> +int xhci_hcd_init(int index, struct xhci_hccr **hccr, struct xhci_hcor
> **hcor) +{
> +	struct zynqmp_xhci *ctx = &zynqmp_xhci;
> +	int ret = 0;
> +
> +	ctx->hcd = (struct xhci_hccr *)ctr_addr[index];
> +	ctx->dwc3_reg = (struct dwc3 *)((char *)(ctx->hcd) + DWC3_REG_OFFSET);
> +
> +	ret = board_usb_init(index, USB_INIT_HOST);
> +	if (ret != 0) {
> +		puts("Failed to initialize board for USB\n");
> +		return ret;
> +	}
> +
> +	ret = zynqmp_xhci_core_init(ctx);
> +	if (ret < 0) {
> +		puts("Failed to initialize xhci\n");
> +		return ret;
> +	}
> +
> +	*hccr = (struct xhci_hccr *)ctx->hcd;
> +	*hcor = (struct xhci_hcor *)((uint32_t) *hccr
> +				+ HC_LENGTH(xhci_readl(&(*hccr)->cr_capbase)));
> +
> +	debug("zynqmp-xhci: init hccr %x and hcor %x hc_length %d\n",

Use %p in the formating string to print pointers and drop the type casts.

> +	      (uint32_t)*hccr, (uint32_t)*hcor,
> +	      (uint32_t)HC_LENGTH(xhci_readl(&(*hccr)->cr_capbase)));
> +
> +	return ret;
> +}
> +
> +void xhci_hcd_stop(int index)
> +{
> +	/*
> +	 * Currently zynqmp socs do not support PHY shutdown from
> +	 * sw. But this support may be added in future socs.
> +	 */
> +
> +	return 0;
> +}