[U-Boot] [PATCH v2 09/11] net: designware: Add support to PCI designware devices

[Simon Glass]

Hi Bin,

On 2 September 2015 at 03:17, Bin Meng <bmeng.cn at gmail.com> wrote:
> The Designware ethernet controller is also seen on PCI bus, e.g.
> on Intel Quark SoC. Add this support in the DM version driver.
>
> Signed-off-by: Bin Meng <bmeng.cn at gmail.com>
>
> ---
>
> Changes in v2:
> - Change to use device_is_on_pci_bus()
>
>  drivers/net/designware.c | 39 +++++++++++++++++++++++++++++++++++++++
>  1 file changed, 39 insertions(+)
>
> diff --git a/drivers/net/designware.c b/drivers/net/designware.c
> index ae78d21..39a9e6b 100644
> --- a/drivers/net/designware.c
> +++ b/drivers/net/designware.c
> @@ -14,6 +14,7 @@
>  #include <errno.h>
>  #include <miiphy.h>
>  #include <malloc.h>
> +#include <pci.h>
>  #include <linux/compiler.h>
>  #include <linux/err.h>
>  #include <asm/io.h>
> @@ -558,6 +559,20 @@ static int designware_eth_write_hwaddr(struct udevice *dev)
>         return _dw_write_hwaddr(priv, pdata->enetaddr);
>  }
>
> +static int designware_eth_bind(struct udevice *dev)
> +{
> +       static int num_cards;
> +       char name[20];
> +
> +       /* Create a unique device name for PCI type devices */
> +       if (device_is_on_pci_bus(dev)) {
> +               sprintf(name, "eth_designware#%u", num_cards++);
> +               device_set_name(dev, name);
> +       }
> +
> +       return 0;
> +}
> +
>  static int designware_eth_probe(struct udevice *dev)
>  {
>         struct eth_pdata *pdata = dev_get_platdata(dev);
> @@ -565,6 +580,22 @@ static int designware_eth_probe(struct udevice *dev)
>         u32 iobase = pdata->iobase;
>         int ret;
>
> +       /*
> +        * If we are on PCI bus, either directly attached to a PCI root port,
> +        * or via a PCI bridge, fill in platdata before we probe the hardware.
> +        */
> +       if (device_is_on_pci_bus(dev)) {
> +               pci_dev_t bdf;
> +
> +               bdf = pci_get_bdf(dev);
> +               pci_read_config_dword(bdf, PCI_BASE_ADDRESS_0, &iobase);

Can we use a dm_pci_...() function here?

> +               iobase &= PCI_BASE_ADDRESS_MEM_MASK;
> +               iobase = pci_mem_to_phys(bdf, iobase);
> +
> +               pdata->iobase = iobase;
> +               pdata->phy_interface = PHY_INTERFACE_MODE_RMII;
> +       }
> +
>         debug("%s, iobase=%x, priv=%p\n", __func__, iobase, priv);
>         priv->mac_regs_p = (struct eth_mac_regs *)iobase;
>         priv->dma_regs_p = (struct eth_dma_regs *)(iobase + DW_DMA_BASE_OFFSET);
> @@ -617,10 +648,18 @@ U_BOOT_DRIVER(eth_designware) = {
>         .id     = UCLASS_ETH,
>         .of_match = designware_eth_ids,
>         .ofdata_to_platdata = designware_eth_ofdata_to_platdata,
> +       .bind   = designware_eth_bind,
>         .probe  = designware_eth_probe,
>         .ops    = &designware_eth_ops,
>         .priv_auto_alloc_size = sizeof(struct dw_eth_dev),
>         .platdata_auto_alloc_size = sizeof(struct eth_pdata),
>         .flags = DM_FLAG_ALLOC_PRIV_DMA,
>  };
> +
> +static struct pci_device_id supported[] = {
> +       { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_QRK_EMAC) },
> +       { }
> +};
> +
> +U_BOOT_PCI_DEVICE(eth_designware, supported);
>  #endif
> --
> 1.8.2.1
>

Regards,
Simon