[U-Boot] [PATCH] sunxi: Add q8_a13_tablet defconfig and dts
Hans de Goede
hdegoede at redhat.com
Sat Sep 5 17:05:12 CEST 2015
This commits adds a generic support for q8 formfactor a13 based tablets.
These tablets ship in many variants, with the difference mainly being the
touchscreen controller / accelerometer / wifi chip used.
The wifi is USB based, and thus not listed in devicetree.
ATM the kernel does not support the touchscreen / accelerometer on these
devices. In the future we may need multiple configs with different
CONFIG_DEFAULT_DEVICE_TREE settings, this depends on how we solve the
hw differences on the kernel side.
For now this will suffice.
The dts files are identical to the dts files submitted to the upstream
kernel for these tablets.
Signed-off-by: Hans de Goede <hdegoede at redhat.com>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/sun5i-a13-q8-tablet.dts | 60 +++++++++++++
arch/arm/dts/sun5i-q8-common.dtsi | 170 +++++++++++++++++++++++++++++++++++
arch/arm/dts/sunxi-q8-common.dtsi | 77 ++++++++++++++++
board/sunxi/MAINTAINERS | 1 +
configs/q8_a13_tablet_defconfig | 23 +++++
6 files changed, 332 insertions(+)
create mode 100644 arch/arm/dts/sun5i-a13-q8-tablet.dts
create mode 100644 arch/arm/dts/sun5i-q8-common.dtsi
create mode 100644 arch/arm/dts/sunxi-q8-common.dtsi
create mode 100644 configs/q8_a13_tablet_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 52b6275..275948d 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -103,6 +103,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \
sun5i-a13-inet-98v-rev2.dtb \
sun5i-a13-olinuxino.dtb \
sun5i-a13-olinuxino-micro.dtb \
+ sun5i-a13-q8-tablet.dtb \
sun5i-a13-tzx-q8-713b7.dtb \
sun5i-a13-utoo-p66.dtb \
sun5i-r8-chip.dtb
diff --git a/arch/arm/dts/sun5i-a13-q8-tablet.dts b/arch/arm/dts/sun5i-a13-q8-tablet.dts
new file mode 100644
index 0000000..72e93ac
--- /dev/null
+++ b/arch/arm/dts/sun5i-a13-q8-tablet.dts
@@ -0,0 +1,60 @@
+/*
+ * Copyright 2015 Hans de Goede <hdegoede at redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+#include "sun5i-q8-common.dtsi"
+
+/ {
+ model = "Q8 A13 Tablet";
+ compatible = "allwinner,q8-a13", "allwinner,sun5i-a13";
+};
+
+®_ldo3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_ldo3>;
+};
diff --git a/arch/arm/dts/sun5i-q8-common.dtsi b/arch/arm/dts/sun5i-q8-common.dtsi
new file mode 100644
index 0000000..0641d68
--- /dev/null
+++ b/arch/arm/dts/sun5i-q8-common.dtsi
@@ -0,0 +1,170 @@
+/*
+ * Copyright 2015 Hans de Goede <hdegoede at redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include "sunxi-q8-common.dtsi"
+
+/ {
+ aliases {
+ serial0 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&i2c0 {
+ axp209: pmic at 34 {
+ reg = <0x34>;
+ interrupts = <0>;
+ };
+};
+
+&i2c1 {
+ pcf8563: rtc at 51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+#include "axp209.dtsi"
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_q8>;
+ vmmc-supply = <®_vcc3v0>;
+ bus-width = <4>;
+ cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
+ cd-inverted;
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+&pio {
+ mmc0_cd_pin_q8: mmc0_cd_pin at 0 {
+ allwinner,pins = "PG0";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb0_vbus_detect_pin: usb0_vbus_detect_pin at 0 {
+ allwinner,pins = "PG1";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ };
+
+ usb0_id_detect_pin: usb0_id_detect_pin at 0 {
+ allwinner,pins = "PG2";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb0_vbus_pin_a: usb0_vbus_pin at 0 {
+ allwinner,pins = "PG12";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-pll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb0_vbus {
+ gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_b>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
+ usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+ usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+ usb0_vbus-supply = <®_usb0_vbus>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/sunxi-q8-common.dtsi b/arch/arm/dts/sunxi-q8-common.dtsi
new file mode 100644
index 0000000..17b26ff
--- /dev/null
+++ b/arch/arm/dts/sunxi-q8-common.dtsi
@@ -0,0 +1,77 @@
+/*
+ * Copyright 2015 Hans de Goede <hdegoede at redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include "sunxi-common-regulators.dtsi"
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&lradc {
+ vref-supply = <®_vcc3v0>;
+ status = "okay";
+
+ button at 200 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <200000>;
+ };
+
+ button at 400 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <400000>;
+ };
+};
diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
index 3f897f8..7f29b58 100644
--- a/board/sunxi/MAINTAINERS
+++ b/board/sunxi/MAINTAINERS
@@ -24,6 +24,7 @@ F: configs/Auxtek-T003_defconfig
F: configs/Auxtek-T004_defconfig
F: configs/inet98v_rev2_defconfig
F: configs/mk802_a10s_defconfig
+F: configs/q8_a13_tablet_defconfig
F: configs/r7-tv-dongle_defconfig
F: configs/UTOO_P66_defconfig
F: include/configs/sun6i.h
diff --git a/configs/q8_a13_tablet_defconfig b/configs/q8_a13_tablet_defconfig
new file mode 100644
index 0000000..d38e41f
--- /dev/null
+++ b/configs/q8_a13_tablet_defconfig
@@ -0,0 +1,23 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN5I=y
+CONFIG_DRAM_CLK=384
+CONFIG_DRAM_EMR1=0
+CONFIG_MMC0_CD_PIN="PG0"
+CONFIG_USB0_VBUS_PIN="PG12"
+CONFIG_USB0_VBUS_DET="PG1"
+CONFIG_USB0_ID_DET="PG2"
+CONFIG_AXP_GPIO=y
+# CONFIG_VIDEO_HDMI is not set
+CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:45,ri:82,up:22,lo:22,hs:1,vs:1,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_POWER="AXP0-0"
+CONFIG_VIDEO_LCD_BL_EN="AXP0-1"
+CONFIG_VIDEO_LCD_BL_PWM="PB2"
+CONFIG_USB_MUSB_HOST=y
+CONFIG_DEFAULT_DEVICE_TREE="sun5i-a13-q8-tablet"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=2,AXP209_POWER"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
--
2.4.3
More information about the U-Boot
mailing list