[U-Boot] [PATCH] imx: mx6ul: support mx6ul 9x9 evk board
Peng Fan
b51431 at freescale.com
Sun Sep 6 07:53:13 CEST 2015
New version V2: https://patchwork.ozlabs.org/patch/514899/
Regards,
Peng.
On Sun, Sep 06, 2015 at 12:49:21PM +0800, Peng Fan wrote:
>This patch is to support mx6ul_9x9_evk board based on mx6ul_14x14_evk,
>the difference between mx6ul 9x9 evk and mx6ul 14x14 evk are:
>1. mx6ul 9x9 evk use pfuze3000, while mx6ul 14x14 evk use DCDC.
>2. mx6ul 9x9 evk supports 256MB LPDDR2, while mx6ul 14x14 evk
> supports 512MB DDR3
>3. mx6ul_9x9_evk use 9x9 package, while mx6ul_14x14_evk use 14x14 package.
>
>This patch add the following:
>1. Discard PHYS_SDRAM_SIZE from header file, use imx_ddr_size()
>2. Introduce a macro is_mx6ul_9x9_evk using
> CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) to avoid "#ifdef xxx" in non-SPL
> part. To SPL part, CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) can not work,
> so still use "#ifdef CONFIG_TARGET_MX6UL_9X9_EVK" to differentiate with
> mx6ul_14x14_evk. And we have no way to dymaically checking this chip
> is 9x9 or 14x14.
>3. mx6ul_9x9_evk use pfuze3000, so enabled POWER related configurations.
> POWER related configurations also effect for mx6ul_14x14_evk. But
> power_init_board implementation using 'if (is_mx6ul_9x9_evk())' to
> do initialization for mx6ul_9x9_evk, and do nothing for mx6ul_14x14_evk.
>4. mx6ul_9x9_evk use lpddr2 with size 256MB, so add related SPL DRAM
> configurations.
>5. Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and setting dtb file
> according to board_rev and board_name.
>6. Add TARGET_MX6UL_9X9_EVK Kconfig entry
>
>Boot Log:
>U-Boot SPL 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53)
>reading u-boot.img
>reading u-boot.img
>
>U-Boot 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53 +0800)
>
>CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
>CPU: Commercial temperature grade (0C to 95C) at 41C
>Reset cause: POR
>Board: MX6UL 9x9 EVK
>I2C: ready
>DRAM: 256 MiB
>PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
>MMC: FSL_SDHC: 0, FSL_SDHC: 1
>In: serial
>Out: serial
>Err: serial
>Net: FEC1
>Hit any key to stop autoboot: 0
>
>Signed-off-by: Peng Fan <Peng.Fan at freescale.com>
>Cc: Stefano Babic <sbabic at denx.de>
>---
> arch/arm/cpu/armv7/mx6/Kconfig | 8 +
> board/freescale/mx6ul_14x14_evk/Kconfig | 2 +-
> board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c | 183 ++++++++++++++++++----
> configs/mx6ul_9x9_evk_defconfig | 8 +
> include/configs/imx6_spl.h | 1 +
> include/configs/mx6ul_14x14_evk.h | 26 ++-
> 6 files changed, 191 insertions(+), 37 deletions(-)
> create mode 100644 configs/mx6ul_9x9_evk_defconfig
>
>diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig
>index 8b0120f..b3f7eaf 100644
>--- a/arch/arm/cpu/armv7/mx6/Kconfig
>+++ b/arch/arm/cpu/armv7/mx6/Kconfig
>@@ -104,6 +104,14 @@ config TARGET_MX6SXSABRESD
> select DM
> select DM_THERMAL
>
>+config TARGET_MX6UL_9X9_EVK
>+ bool "mx6ul_9x9_evk"
>+ select MX6UL
>+ select CPU_V7
>+ select DM
>+ select DM_THERMAL
>+ select SUPPORT_SPL
>+
> config TARGET_MX6UL_14X14_EVK
> bool "mx6ul_14x14_evk"
> select MX6UL
>diff --git a/board/freescale/mx6ul_14x14_evk/Kconfig b/board/freescale/mx6ul_14x14_evk/Kconfig
>index 393aca6..eda02c9 100644
>--- a/board/freescale/mx6ul_14x14_evk/Kconfig
>+++ b/board/freescale/mx6ul_14x14_evk/Kconfig
>@@ -1,4 +1,4 @@
>-if TARGET_MX6UL_14X14_EVK
>+if TARGET_MX6UL_14X14_EVK || TARGET_MX6UL_9X9_EVK
>
> config SYS_BOARD
> default "mx6ul_14x14_evk"
>diff --git a/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c b/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
>index c09d84e..612fb78 100644
>--- a/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
>+++ b/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
>@@ -23,6 +23,9 @@
> #include <linux/sizes.h>
> #include <mmc.h>
> #include <netdev.h>
>+#include <power/pmic.h>
>+#include <power/pfuze3000_pmic.h>
>+#include "../common/pfuze.h"
> #include <usb.h>
> #include <usb/ehci-fsl.h>
>
>@@ -210,11 +213,56 @@ struct i2c_pads_info i2c_pad_info1 = {
> .gp = IMX_GPIO_NR(1, 29),
> },
> };
>+
>+#ifdef CONFIG_POWER
>+#define I2C_PMIC 0
>+int power_init_board(void)
>+{
>+ if (is_mx6ul_9x9_evk()) {
>+ struct pmic *pfuze;
>+ int ret;
>+ unsigned int reg, rev_id;
>+
>+ ret = power_pfuze3000_init(I2C_PMIC);
>+ if (ret)
>+ return ret;
>+
>+ pfuze = pmic_get("PFUZE3000");
>+ ret = pmic_probe(pfuze);
>+ if (ret)
>+ return ret;
>+
>+ pmic_reg_read(pfuze, PFUZE3000_DEVICEID, ®);
>+ pmic_reg_read(pfuze, PFUZE3000_REVID, &rev_id);
>+ printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n",
>+ reg, rev_id);
>+
>+ /* disable Low Power Mode during standby mode */
>+ pmic_reg_read(pfuze, PFUZE3000_LDOGCTL, ®);
>+ reg |= 0x1;
>+ pmic_reg_write(pfuze, PFUZE3000_LDOGCTL, reg);
>+
>+ /* SW1B step ramp up time from 2us to 4us/25mV */
>+ reg = 0x40;
>+ pmic_reg_write(pfuze, PFUZE3000_SW1BCONF, reg);
>+
>+ /* SW1B mode to APS/PFM */
>+ reg = 0xc;
>+ pmic_reg_write(pfuze, PFUZE3000_SW1BMODE, reg);
>+
>+ /* SW1B standby voltage set to 0.975V */
>+ reg = 0xb;
>+ pmic_reg_write(pfuze, PFUZE3000_SW1BSTBY, reg);
>+ }
>+
>+ return 0;
>+}
>+#endif
> #endif
>
> int dram_init(void)
> {
>- gd->ram_size = PHYS_SDRAM_SIZE;
>+ gd->ram_size = imx_ddr_size();
>
> return 0;
> }
>@@ -614,6 +662,15 @@ int board_late_init(void)
> add_board_boot_modes(board_boot_modes);
> #endif
>
>+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
>+ setenv("board_name", "EVK");
>+
>+ if (is_mx6ul_9x9_evk())
>+ setenv("board_rev", "9X9");
>+ else
>+ setenv("board_rev", "14X14");
>+#endif
>+
> return 0;
> }
>
>@@ -624,7 +681,10 @@ u32 get_board_rev(void)
>
> int checkboard(void)
> {
>- puts("Board: MX6UL 14x14 EVK\n");
>+ if (is_mx6ul_9x9_evk())
>+ puts("Board: MX6UL 9x9 EVK\n");
>+ else
>+ puts("Board: MX6UL 14x14 EVK\n");
>
> return 0;
> }
>@@ -634,7 +694,76 @@ int checkboard(void)
> #include <spl.h>
> #include <asm/arch/mx6-ddr.h>
>
>-const struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
>+
>+static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
>+ .grp_addds = 0x00000030,
>+ .grp_ddrmode_ctl = 0x00020000,
>+ .grp_b0ds = 0x00000030,
>+ .grp_ctlds = 0x00000030,
>+ .grp_b1ds = 0x00000030,
>+ .grp_ddrpke = 0x00000000,
>+ .grp_ddrmode = 0x00020000,
>+#ifdef CONFIG_TARGET_MX6UL_9X9_EVK
>+ .grp_ddr_type = 0x00080000,
>+#else
>+ .grp_ddr_type = 0x000c0000,
>+#endif
>+};
>+
>+#ifdef CONFIG_TARGET_MX6UL_9X9_EVK
>+static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
>+ .dram_dqm0 = 0x00000030,
>+ .dram_dqm1 = 0x00000030,
>+ .dram_ras = 0x00000030,
>+ .dram_cas = 0x00000030,
>+ .dram_odt0 = 0x00000000,
>+ .dram_odt1 = 0x00000000,
>+ .dram_sdba2 = 0x00000000,
>+ .dram_sdclk_0 = 0x00000030,
>+ .dram_sdqs0 = 0x00003030,
>+ .dram_sdqs1 = 0x00003030,
>+ .dram_reset = 0x00000030,
>+};
>+
>+static struct mx6_mmdc_calibration mx6_mmcd_calib = {
>+ .p0_mpwldectrl0 = 0x00000000,
>+ .p0_mpdgctrl0 = 0x20000000,
>+ .p0_mprddlctl = 0x4040484f,
>+ .p0_mpwrdlctl = 0x40405247,
>+ .mpzqlp2ctl = 0x1b4700c7,
>+};
>+
>+static struct mx6_lpddr2_cfg mem_ddr = {
>+ .mem_speed = 800,
>+ .density = 2,
>+ .width = 16,
>+ .banks = 4,
>+ .rowaddr = 14,
>+ .coladdr = 10,
>+ .trcd_lp = 1500,
>+ .trppb_lp = 1500,
>+ .trpab_lp = 2000,
>+ .trasmin = 4250,
>+};
>+
>+struct mx6_ddr_sysinfo ddr_sysinfo = {
>+ .dsize = 0,
>+ .cs_density = 18,
>+ .ncs = 1,
>+ .cs1_mirror = 0,
>+ .walat = 0,
>+ .ralat = 5,
>+ .mif3_mode = 3,
>+ .bi_on = 1,
>+ .rtt_wr = 0, /* LPDDR2 does not need rtt_wr rtt_nom */
>+ .rtt_nom = 0,
>+ .sde_to_rst = 0, /* LPDDR2 does not need this field */
>+ .rst_to_cke = 0x10, /* JEDEC value for LPDDR2: 200us */
>+ .ddr_type = DDR_TYPE_LPDDR2,
>+};
>+
>+#else
>+static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
> .dram_dqm0 = 0x00000030,
> .dram_dqm1 = 0x00000030,
> .dram_ras = 0x00000030,
>@@ -648,24 +777,29 @@ const struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
> .dram_reset = 0x00000030,
> };
>
>-const struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
>- .grp_addds = 0x00000030,
>- .grp_ddrmode_ctl = 0x00020000,
>- .grp_b0ds = 0x00000030,
>- .grp_ctlds = 0x00000030,
>- .grp_b1ds = 0x00000030,
>- .grp_ddrpke = 0x00000000,
>- .grp_ddrmode = 0x00020000,
>- .grp_ddr_type = 0x000c0000,
>-};
>-
>-const struct mx6_mmdc_calibration mx6_mmcd_calib = {
>+static struct mx6_mmdc_calibration mx6_mmcd_calib = {
> .p0_mpwldectrl0 = 0x00070007,
> .p0_mpdgctrl0 = 0x41490145,
> .p0_mprddlctl = 0x40404546,
> .p0_mpwrdlctl = 0x4040524D,
> };
>
>+struct mx6_ddr_sysinfo ddr_sysinfo = {
>+ .dsize = 0,
>+ .cs_density = 20,
>+ .ncs = 1,
>+ .cs1_mirror = 0,
>+ .rtt_wr = 2,
>+ .rtt_nom = 1, /* RTT_Nom = RZQ/2 */
>+ .walat = 1, /* Write additional latency */
>+ .ralat = 5, /* Read additional latency */
>+ .mif3_mode = 3, /* Command prediction working mode */
>+ .bi_on = 1, /* Bank interleaving enabled */
>+ .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
>+ .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
>+ .ddr_type = DDR_TYPE_DDR3,
>+};
>+
> static struct mx6_ddr3_cfg mem_ddr = {
> .mem_speed = 800,
> .density = 4,
>@@ -678,6 +812,7 @@ static struct mx6_ddr3_cfg mem_ddr = {
> .trcmin = 4875,
> .trasmin = 3500,
> };
>+#endif
>
> static void ccgr_init(void)
> {
>@@ -695,24 +830,8 @@ static void ccgr_init(void)
>
> static void spl_dram_init(void)
> {
>- struct mx6_ddr_sysinfo sysinfo = {
>- .dsize = 0,
>- .cs_density = 20,
>- .ncs = 1,
>- .cs1_mirror = 0,
>- .rtt_wr = 2,
>- .rtt_nom = 1, /* RTT_Nom = RZQ/2 */
>- .walat = 1, /* Write additional latency */
>- .ralat = 5, /* Read additional latency */
>- .mif3_mode = 3, /* Command prediction working mode */
>- .bi_on = 1, /* Bank interleaving enabled */
>- .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
>- .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
>- .ddr_type = DDR_TYPE_DDR3,
>- };
>-
> mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
>- mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr);
>+ mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
> }
>
> void board_init_f(ulong dummy)
>diff --git a/configs/mx6ul_9x9_evk_defconfig b/configs/mx6ul_9x9_evk_defconfig
>new file mode 100644
>index 0000000..e54609d
>--- /dev/null
>+++ b/configs/mx6ul_9x9_evk_defconfig
>@@ -0,0 +1,8 @@
>+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg"
>+CONFIG_ARM=y
>+CONFIG_ARCH_MX6=y
>+CONFIG_TARGET_MX6UL_9X9_EVK=y
>+CONFIG_SPL=y
>+CONFIG_CMD_NET=y
>+CONFIG_CMD_PING=y
>+CONFIG_CMD_DHCP=y
>diff --git a/include/configs/imx6_spl.h b/include/configs/imx6_spl.h
>index 1744f2c..82ec798 100644
>--- a/include/configs/imx6_spl.h
>+++ b/include/configs/imx6_spl.h
>@@ -10,6 +10,7 @@
> #ifdef CONFIG_SPL
>
> #define CONFIG_SPL_FRAMEWORK
>+#include <linux/kconfig.h>
>
> /*
> * see Figure 8-3 in IMX6DQ/IMX6SDL Reference manuals:
>diff --git a/include/configs/mx6ul_14x14_evk.h b/include/configs/mx6ul_14x14_evk.h
>index 4a2280b..4d4db69 100644
>--- a/include/configs/mx6ul_14x14_evk.h
>+++ b/include/configs/mx6ul_14x14_evk.h
>@@ -14,12 +14,16 @@
> #include "mx6_common.h"
> #include <asm/imx-common/gpio.h>
>
>+#define is_mx6ul_9x9_evk() CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK)
>+
> /* SPL options */
> #define CONFIG_SPL_LIBCOMMON_SUPPORT
> #define CONFIG_SPL_MMC_SUPPORT
> #define CONFIG_SPL_FAT_SUPPORT
> #include "imx6_spl.h"
>
>+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
>+
> #define CONFIG_ROM_UNIFIED_SECTIONS
> #define CONFIG_SYS_GENERIC_BOARD
> #define CONFIG_DISPLAY_CPUINFO
>@@ -66,9 +70,13 @@
> #define CONFIG_SYS_I2C
> #define CONFIG_SYS_I2C_MXC
> #define CONFIG_SYS_I2C_SPEED 100000
>-#endif
>
>-#define PHYS_SDRAM_SIZE SZ_512M
>+/* PMIC only for 9X9 EVK */
>+#define CONFIG_POWER
>+#define CONFIG_POWER_I2C
>+#define CONFIG_POWER_PFUZE3000
>+#define CONFIG_POWER_PFUZE3000_I2C_ADDR 0x08
>+#endif
>
> #undef CONFIG_CMD_IMLS
>
>@@ -80,7 +88,7 @@
> "console=ttymxc0\0" \
> "fdt_high=0xffffffff\0" \
> "initrd_high=0xffffffff\0" \
>- "fdt_file=imx6ul-14x14-evk.dtb\0" \
>+ "fdt_file=undefined\0" \
> "fdt_addr=0x83000000\0" \
> "boot_fdt=try\0" \
> "ip_dyn=yes\0" \
>@@ -134,9 +142,19 @@
> "fi; " \
> "else " \
> "bootz; " \
>- "fi;\0"
>+ "fi;\0" \
>+ "findfdt="\
>+ "if test $fdt_file = undefined; then " \
>+ "if test $board_name = EVK && test $board_rev = 9X9; then " \
>+ "setenv fdt_file imx6ul-9x9-evk.dtb; fi; " \
>+ "if test $board_name = EVK && test $board_rev = 14X14; then " \
>+ "setenv fdt_file imx6ul-14x14-evk.dtb; fi; " \
>+ "if test $fdt_file = undefined; then " \
>+ "echo WARNING: Could not determine dtb to use; fi; " \
>+ "fi;\0" \
>
> #define CONFIG_BOOTCOMMAND \
>+ "run findfdt;" \
> "mmc dev ${mmcdev};" \
> "mmc dev ${mmcdev}; if mmc rescan; then " \
> "if run loadbootscript; then " \
>--
>1.8.4
>
>
--
More information about the U-Boot
mailing list