[U-Boot] [PATCH 10/14] armv8/ls1043ardb: Add cpld command to boot from nand

Gong Qianyu Qianyu.Gong at freescale.com
Fri Sep 11 13:07:24 CEST 2015


Signed-off-by: Gong Qianyu <Qianyu.Gong at freescale.com>
---
 board/freescale/ls1043ardb/cpld.c | 18 ++++++++++++++++++
 board/freescale/ls1043ardb/cpld.h |  1 +
 2 files changed, 19 insertions(+)

diff --git a/board/freescale/ls1043ardb/cpld.c b/board/freescale/ls1043ardb/cpld.c
index 3f1101e..5acb97d 100644
--- a/board/freescale/ls1043ardb/cpld.c
+++ b/board/freescale/ls1043ardb/cpld.c
@@ -45,6 +45,21 @@ void cpld_set_defbank(void)
 	CPLD_WRITE(global_rst, 1);
 }
 
+void cpld_set_nand(void)
+{
+	u16 reg = CPLD_CFG_RCW_SRC_NAND;
+	u8 reg5 = (u8)(reg >> 1);
+	u8 reg6 = (u8)(reg & 1);
+	cpld_rev_bit(&reg5);
+
+	CPLD_WRITE(soft_mux_on, 1);
+
+	CPLD_WRITE(cfg_rcw_src1, reg5);
+	CPLD_WRITE(cfg_rcw_src2, reg6);
+
+	CPLD_WRITE(system_rst, 1);
+}
+
 #ifdef DEBUG
 static void cpld_dump_regs(void)
 {
@@ -91,6 +106,8 @@ int do_cpld(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 	if (strcmp(argv[1], "reset") == 0) {
 		if (strcmp(argv[2], "altbank") == 0)
 			cpld_set_altbank();
+		else if (strcmp(argv[2], "nand") == 0)
+			cpld_set_nand();
 		else
 			cpld_set_defbank();
 #ifdef DEBUG
@@ -109,6 +126,7 @@ U_BOOT_CMD(
 	"Reset the board or alternate bank",
 	"reset: reset to default bank\n"
 	"cpld reset altbank: reset to alternate bank\n"
+	"cpld reset nand: reset to boot from NAND flash\n"
 #ifdef DEBUG
 	"cpld dump - display the CPLD registers\n"
 #endif
diff --git a/board/freescale/ls1043ardb/cpld.h b/board/freescale/ls1043ardb/cpld.h
index ea4efd8..5f43a8a 100644
--- a/board/freescale/ls1043ardb/cpld.h
+++ b/board/freescale/ls1043ardb/cpld.h
@@ -40,4 +40,5 @@ void cpld_rev_bit(unsigned char *value);
 #define CPLD_SW_MUX_BANK_SEL	0x40
 #define CPLD_BANK_SEL_MASK	0x07
 #define CPLD_BANK_SEL_ALTBANK	0x04
+#define CPLD_CFG_RCW_SRC_NAND	0x106
 #endif
-- 
2.1.0.27.g96db324



More information about the U-Boot mailing list