[U-Boot] [PATCH v2 17/18] ARM: uniphier: remove ifdef CONFIG_{SOC} conditionals from sg-regs.h
Masahiro Yamada
yamada.masahiro at socionext.com
Fri Sep 11 13:17:48 CEST 2015
To achieve the complete run-time configuration by device trees, ifdef
conditionals in header files are not preferable.
Signed-off-by: Masahiro Yamada <yamada.masahiro at socionext.com>
---
Changes in v2: None
arch/arm/mach-uniphier/include/mach/sg-regs.h | 40 +++++++------------
arch/arm/mach-uniphier/ph1-ld4/lowlevel_debug.S | 4 +-
arch/arm/mach-uniphier/ph1-ld4/pinctrl.c | 46 +++++++++++-----------
arch/arm/mach-uniphier/ph1-pro4/lowlevel_debug.S | 4 +-
arch/arm/mach-uniphier/ph1-pro4/pinctrl.c | 50 ++++++++++++------------
arch/arm/mach-uniphier/ph1-sld3/early_pinctrl.c | 12 +++---
arch/arm/mach-uniphier/ph1-sld3/lowlevel_debug.S | 4 +-
arch/arm/mach-uniphier/ph1-sld3/pinctrl.c | 16 ++++----
arch/arm/mach-uniphier/ph1-sld3/sbc_init.c | 2 +-
arch/arm/mach-uniphier/ph1-sld8/lowlevel_debug.S | 4 +-
arch/arm/mach-uniphier/ph1-sld8/pinctrl.c | 46 +++++++++++-----------
11 files changed, 109 insertions(+), 119 deletions(-)
diff --git a/arch/arm/mach-uniphier/include/mach/sg-regs.h b/arch/arm/mach-uniphier/include/mach/sg-regs.h
index 43a6c35..c886e1c 100644
--- a/arch/arm/mach-uniphier/include/mach/sg-regs.h
+++ b/arch/arm/mach-uniphier/include/mach/sg-regs.h
@@ -53,24 +53,6 @@
/* Pin Control */
#define SG_PINCTRL_BASE (SG_CTRL_BASE | 0x1000)
-#if defined(CONFIG_MACH_PH1_PRO4)
-# define SG_PINCTRL(n) (SG_PINCTRL_BASE + (n) * 8)
-#elif defined(CONFIG_MACH_PH1_SLD3) || defined(CONFIG_MACH_PH1_LD4) || \
- defined(CONFIG_MACH_PH1_SLD8)
-# define SG_PINCTRL(n) (SG_PINCTRL_BASE + (n) * 4)
-#endif
-
-#if defined(CONFIG_MACH_PH1_SLD3) || defined(CONFIG_MACH_PH1_PRO4)
-#define SG_PINSELBITS 4
-#elif defined(CONFIG_MACH_PH1_LD4) || defined(CONFIG_MACH_PH1_SLD8)
-#define SG_PINSELBITS 8
-#endif
-
-#define SG_PINSEL_ADDR(n) (SG_PINCTRL((n) * (SG_PINSELBITS) / 32))
-#define SG_PINSEL_MASK(n) (~(((1 << (SG_PINSELBITS)) - 1) << \
- ((n) * (SG_PINSELBITS) % 32)))
-#define SG_PINSEL_MODE(n, mode) ((mode) << ((n) * (SG_PINSELBITS) % 32))
-
/* Only for PH1-Pro4 */
#define SG_LOADPINCTRL (SG_CTRL_BASE | 0x1700)
@@ -98,11 +80,11 @@
#ifdef __ASSEMBLY__
- .macro set_pinsel, n, value, ra, rd
- ldr \ra, =SG_PINSEL_ADDR(\n)
+ .macro sg_set_pinsel, pin, muxval, mux_bits, reg_stride, ra, rd
+ ldr \ra, =(SG_PINCTRL_BASE + \pin * \mux_bits / 32 * \reg_stride)
ldr \rd, [\ra]
- and \rd, \rd, #SG_PINSEL_MASK(\n)
- orr \rd, \rd, #SG_PINSEL_MODE(\n, \value)
+ and \rd, \rd, #~(((1 << \mux_bits) - 1) << (\pin * \mux_bits % 32))
+ orr \rd, \rd, #(\muxval << (\pin * \mux_bits % 32))
str \rd, [\ra]
.endm
@@ -111,10 +93,18 @@
#include <linux/types.h>
#include <linux/io.h>
-static inline void sg_set_pinsel(int n, int value)
+static inline void sg_set_pinsel(unsigned pin, unsigned muxval,
+ unsigned mux_bits, unsigned reg_stride)
{
- writel((readl(SG_PINSEL_ADDR(n)) & SG_PINSEL_MASK(n))
- | SG_PINSEL_MODE(n, value), SG_PINSEL_ADDR(n));
+ unsigned shift = pin * mux_bits % 32;
+ unsigned reg = SG_PINCTRL_BASE + pin * mux_bits / 32 * reg_stride;
+ u32 mask = (1U << mux_bits) - 1;
+ u32 tmp;
+
+ tmp = readl(reg);
+ tmp &= ~(mask << shift);
+ tmp |= (mask & muxval) << shift;
+ writel(tmp, reg);
}
#endif /* __ASSEMBLY__ */
diff --git a/arch/arm/mach-uniphier/ph1-ld4/lowlevel_debug.S b/arch/arm/mach-uniphier/ph1-ld4/lowlevel_debug.S
index 7928c5c..fd393dc 100644
--- a/arch/arm/mach-uniphier/ph1-ld4/lowlevel_debug.S
+++ b/arch/arm/mach-uniphier/ph1-ld4/lowlevel_debug.S
@@ -17,8 +17,8 @@ ENTRY(setup_lowlevel_debug)
init_debug_uart r0, r1, r2
/* UART Port 0 */
- set_pinsel 85, 1, r0, r1
- set_pinsel 88, 1, r0, r1
+ sg_set_pinsel 85, 1, 8, 4, r0, r1
+ sg_set_pinsel 88, 1, 8, 4, r0, r1
ldr r0, =SG_IECTRL
ldr r1, [r0]
diff --git a/arch/arm/mach-uniphier/ph1-ld4/pinctrl.c b/arch/arm/mach-uniphier/ph1-ld4/pinctrl.c
index 20cc7b3..293a6ab 100644
--- a/arch/arm/mach-uniphier/ph1-ld4/pinctrl.c
+++ b/arch/arm/mach-uniphier/ph1-ld4/pinctrl.c
@@ -14,32 +14,32 @@ void pin_init(void)
/* Comment format: PAD Name -> Function Name */
#ifdef CONFIG_NAND_DENALI
- sg_set_pinsel(158, 0); /* XNFRE -> XNFRE_GB */
- sg_set_pinsel(159, 0); /* XNFWE -> XNFWE_GB */
- sg_set_pinsel(160, 0); /* XFALE -> NFALE_GB */
- sg_set_pinsel(161, 0); /* XFCLE -> NFCLE_GB */
- sg_set_pinsel(162, 0); /* XNFWP -> XFNWP_GB */
- sg_set_pinsel(163, 0); /* XNFCE0 -> XNFCE0_GB */
- sg_set_pinsel(164, 0); /* NANDRYBY0 -> NANDRYBY0_GB */
- sg_set_pinsel(22, 0); /* MMCCLK -> XFNCE1_GB */
- sg_set_pinsel(23, 0); /* MMCCMD -> NANDRYBY1_GB */
- sg_set_pinsel(24, 0); /* MMCDAT0 -> NFD0_GB */
- sg_set_pinsel(25, 0); /* MMCDAT1 -> NFD1_GB */
- sg_set_pinsel(26, 0); /* MMCDAT2 -> NFD2_GB */
- sg_set_pinsel(27, 0); /* MMCDAT3 -> NFD3_GB */
- sg_set_pinsel(28, 0); /* MMCDAT4 -> NFD4_GB */
- sg_set_pinsel(29, 0); /* MMCDAT5 -> NFD5_GB */
- sg_set_pinsel(30, 0); /* MMCDAT6 -> NFD6_GB */
- sg_set_pinsel(31, 0); /* MMCDAT7 -> NFD7_GB */
+ sg_set_pinsel(158, 0, 8, 4); /* XNFRE -> XNFRE_GB */
+ sg_set_pinsel(159, 0, 8, 4); /* XNFWE -> XNFWE_GB */
+ sg_set_pinsel(160, 0, 8, 4); /* XFALE -> NFALE_GB */
+ sg_set_pinsel(161, 0, 8, 4); /* XFCLE -> NFCLE_GB */
+ sg_set_pinsel(162, 0, 8, 4); /* XNFWP -> XFNWP_GB */
+ sg_set_pinsel(163, 0, 8, 4); /* XNFCE0 -> XNFCE0_GB */
+ sg_set_pinsel(164, 0, 8, 4); /* NANDRYBY0 -> NANDRYBY0_GB */
+ sg_set_pinsel(22, 0, 8, 4); /* MMCCLK -> XFNCE1_GB */
+ sg_set_pinsel(23, 0, 8, 4); /* MMCCMD -> NANDRYBY1_GB */
+ sg_set_pinsel(24, 0, 8, 4); /* MMCDAT0 -> NFD0_GB */
+ sg_set_pinsel(25, 0, 8, 4); /* MMCDAT1 -> NFD1_GB */
+ sg_set_pinsel(26, 0, 8, 4); /* MMCDAT2 -> NFD2_GB */
+ sg_set_pinsel(27, 0, 8, 4); /* MMCDAT3 -> NFD3_GB */
+ sg_set_pinsel(28, 0, 8, 4); /* MMCDAT4 -> NFD4_GB */
+ sg_set_pinsel(29, 0, 8, 4); /* MMCDAT5 -> NFD5_GB */
+ sg_set_pinsel(30, 0, 8, 4); /* MMCDAT6 -> NFD6_GB */
+ sg_set_pinsel(31, 0, 8, 4); /* MMCDAT7 -> NFD7_GB */
#endif
#ifdef CONFIG_USB_EHCI_UNIPHIER
- sg_set_pinsel(53, 0); /* USB0VBUS -> USB0VBUS */
- sg_set_pinsel(54, 0); /* USB0OD -> USB0OD */
- sg_set_pinsel(55, 0); /* USB1VBUS -> USB1VBUS */
- sg_set_pinsel(56, 0); /* USB1OD -> USB1OD */
- /* sg_set_pinsel(67, 23); */ /* PCOE -> USB2VBUS */
- /* sg_set_pinsel(68, 23); */ /* PCWAIT -> USB2OD */
+ sg_set_pinsel(53, 0, 8, 4); /* USB0VBUS -> USB0VBUS */
+ sg_set_pinsel(54, 0, 8, 4); /* USB0OD -> USB0OD */
+ sg_set_pinsel(55, 0, 8, 4); /* USB1VBUS -> USB1VBUS */
+ sg_set_pinsel(56, 0, 8, 4); /* USB1OD -> USB1OD */
+ /* sg_set_pinsel(67, 23, 8, 4); */ /* PCOE -> USB2VBUS */
+ /* sg_set_pinsel(68, 23, 8, 4); */ /* PCWAIT -> USB2OD */
#endif
tmp = readl(SG_IECTRL);
diff --git a/arch/arm/mach-uniphier/ph1-pro4/lowlevel_debug.S b/arch/arm/mach-uniphier/ph1-pro4/lowlevel_debug.S
index fcaf6d1..19bef2a 100644
--- a/arch/arm/mach-uniphier/ph1-pro4/lowlevel_debug.S
+++ b/arch/arm/mach-uniphier/ph1-pro4/lowlevel_debug.S
@@ -23,8 +23,8 @@ ENTRY(setup_lowlevel_debug)
init_debug_uart r0, r1, r2
/* UART Port 0 */
- set_pinsel 127, 0, r0, r1
- set_pinsel 128, 0, r0, r1
+ sg_set_pinsel 127, 0, 4, 8, r0, r1
+ sg_set_pinsel 128, 0, 4, 8, r0, r1
ldr r0, =SG_LOADPINCTRL
mov r1, #1
diff --git a/arch/arm/mach-uniphier/ph1-pro4/pinctrl.c b/arch/arm/mach-uniphier/ph1-pro4/pinctrl.c
index 2a5a296..bfaff4f 100644
--- a/arch/arm/mach-uniphier/ph1-pro4/pinctrl.c
+++ b/arch/arm/mach-uniphier/ph1-pro4/pinctrl.c
@@ -12,37 +12,37 @@ void pin_init(void)
/* Comment format: PAD Name -> Function Name */
#ifdef CONFIG_NAND_DENALI
- sg_set_pinsel(40, 0); /* NFD0 -> NFD0 */
- sg_set_pinsel(41, 0); /* NFD1 -> NFD1 */
- sg_set_pinsel(42, 0); /* NFD2 -> NFD2 */
- sg_set_pinsel(43, 0); /* NFD3 -> NFD3 */
- sg_set_pinsel(44, 0); /* NFD4 -> NFD4 */
- sg_set_pinsel(45, 0); /* NFD5 -> NFD5 */
- sg_set_pinsel(46, 0); /* NFD6 -> NFD6 */
- sg_set_pinsel(47, 0); /* NFD7 -> NFD7 */
- sg_set_pinsel(48, 0); /* NFALE -> NFALE */
- sg_set_pinsel(49, 0); /* NFCLE -> NFCLE */
- sg_set_pinsel(50, 0); /* XNFRE -> XNFRE */
- sg_set_pinsel(51, 0); /* XNFWE -> XNFWE */
- sg_set_pinsel(52, 0); /* XNFWP -> XNFWP */
- sg_set_pinsel(53, 0); /* XNFCE0 -> XNFCE0 */
- sg_set_pinsel(54, 0); /* NRYBY0 -> NRYBY0 */
- /* sg_set_pinsel(131, 1); */ /* RXD2 -> NRYBY1 */
- /* sg_set_pinsel(132, 1); */ /* TXD2 -> XNFCE1 */
+ sg_set_pinsel(40, 0, 4, 8); /* NFD0 -> NFD0 */
+ sg_set_pinsel(41, 0, 4, 8); /* NFD1 -> NFD1 */
+ sg_set_pinsel(42, 0, 4, 8); /* NFD2 -> NFD2 */
+ sg_set_pinsel(43, 0, 4, 8); /* NFD3 -> NFD3 */
+ sg_set_pinsel(44, 0, 4, 8); /* NFD4 -> NFD4 */
+ sg_set_pinsel(45, 0, 4, 8); /* NFD5 -> NFD5 */
+ sg_set_pinsel(46, 0, 4, 8); /* NFD6 -> NFD6 */
+ sg_set_pinsel(47, 0, 4, 8); /* NFD7 -> NFD7 */
+ sg_set_pinsel(48, 0, 4, 8); /* NFALE -> NFALE */
+ sg_set_pinsel(49, 0, 4, 8); /* NFCLE -> NFCLE */
+ sg_set_pinsel(50, 0, 4, 8); /* XNFRE -> XNFRE */
+ sg_set_pinsel(51, 0, 4, 8); /* XNFWE -> XNFWE */
+ sg_set_pinsel(52, 0, 4, 8); /* XNFWP -> XNFWP */
+ sg_set_pinsel(53, 0, 4, 8); /* XNFCE0 -> XNFCE0 */
+ sg_set_pinsel(54, 0, 4, 8); /* NRYBY0 -> NRYBY0 */
+ /* sg_set_pinsel(131, 1, 4, 8); */ /* RXD2 -> NRYBY1 */
+ /* sg_set_pinsel(132, 1, 4, 8); */ /* TXD2 -> XNFCE1 */
#endif
#ifdef CONFIG_USB_XHCI_UNIPHIER
- sg_set_pinsel(180, 0); /* USB0VBUS -> USB0VBUS */
- sg_set_pinsel(181, 0); /* USB0OD -> USB0OD */
- sg_set_pinsel(182, 0); /* USB1VBUS -> USB1VBUS */
- sg_set_pinsel(183, 0); /* USB1OD -> USB1OD */
+ sg_set_pinsel(180, 0, 4, 8); /* USB0VBUS -> USB0VBUS */
+ sg_set_pinsel(181, 0, 4, 8); /* USB0OD -> USB0OD */
+ sg_set_pinsel(182, 0, 4, 8); /* USB1VBUS -> USB1VBUS */
+ sg_set_pinsel(183, 0, 4, 8); /* USB1OD -> USB1OD */
#endif
#ifdef CONFIG_USB_EHCI_UNIPHIER
- sg_set_pinsel(184, 0); /* USB2VBUS -> USB2VBUS */
- sg_set_pinsel(185, 0); /* USB2OD -> USB2OD */
- sg_set_pinsel(187, 0); /* USB3VBUS -> USB3VBUS */
- sg_set_pinsel(188, 0); /* USB3OD -> USB3OD */
+ sg_set_pinsel(184, 0, 4, 8); /* USB2VBUS -> USB2VBUS */
+ sg_set_pinsel(185, 0, 4, 8); /* USB2OD -> USB2OD */
+ sg_set_pinsel(187, 0, 4, 8); /* USB3VBUS -> USB3VBUS */
+ sg_set_pinsel(188, 0, 4, 8); /* USB3OD -> USB3OD */
#endif
writel(1, SG_LOADPINCTRL);
diff --git a/arch/arm/mach-uniphier/ph1-sld3/early_pinctrl.c b/arch/arm/mach-uniphier/ph1-sld3/early_pinctrl.c
index f113e65..f6ceef5 100644
--- a/arch/arm/mach-uniphier/ph1-sld3/early_pinctrl.c
+++ b/arch/arm/mach-uniphier/ph1-sld3/early_pinctrl.c
@@ -11,13 +11,13 @@ void early_pin_init(void)
/* Comment format: PAD Name -> Function Name */
#ifdef CONFIG_UNIPHIER_SERIAL
- sg_set_pinsel(63, 0); /* RXD0 */
- sg_set_pinsel(64, 1); /* TXD0 */
+ sg_set_pinsel(63, 0, 4, 4); /* RXD0 */
+ sg_set_pinsel(64, 1, 4, 4); /* TXD0 */
- sg_set_pinsel(65, 0); /* RXD1 */
- sg_set_pinsel(66, 1); /* TXD1 */
+ sg_set_pinsel(65, 0, 4, 4); /* RXD1 */
+ sg_set_pinsel(66, 1, 4, 4); /* TXD1 */
- sg_set_pinsel(96, 2); /* RXD2 */
- sg_set_pinsel(102, 2); /* TXD2 */
+ sg_set_pinsel(96, 2, 4, 4); /* RXD2 */
+ sg_set_pinsel(102, 2, 4, 4); /* TXD2 */
#endif
}
diff --git a/arch/arm/mach-uniphier/ph1-sld3/lowlevel_debug.S b/arch/arm/mach-uniphier/ph1-sld3/lowlevel_debug.S
index 41f67b7..ee2eae6 100644
--- a/arch/arm/mach-uniphier/ph1-sld3/lowlevel_debug.S
+++ b/arch/arm/mach-uniphier/ph1-sld3/lowlevel_debug.S
@@ -26,8 +26,8 @@ ENTRY(setup_lowlevel_debug)
init_debug_uart r0, r1, r2
- set_pinsel 63, 0, r0, r1
- set_pinsel 64, 1, r0, r1
+ sg_set_pinsel 63, 0, 4, 4, r0, r1
+ sg_set_pinsel 64, 1, 4, 4, r0, r1
mov pc, lr
ENDPROC(setup_lowlevel_debug)
diff --git a/arch/arm/mach-uniphier/ph1-sld3/pinctrl.c b/arch/arm/mach-uniphier/ph1-sld3/pinctrl.c
index 5ecbe4c..dea938e 100644
--- a/arch/arm/mach-uniphier/ph1-sld3/pinctrl.c
+++ b/arch/arm/mach-uniphier/ph1-sld3/pinctrl.c
@@ -9,16 +9,16 @@
void pin_init(void)
{
#ifdef CONFIG_USB_EHCI_UNIPHIER
- sg_set_pinsel(13, 0); /* USB0OC */
- sg_set_pinsel(14, 1); /* USB0VBUS */
+ sg_set_pinsel(13, 0, 4, 4); /* USB0OC */
+ sg_set_pinsel(14, 1, 4, 4); /* USB0VBUS */
- sg_set_pinsel(15, 0); /* USB1OC */
- sg_set_pinsel(16, 1); /* USB1VBUS */
+ sg_set_pinsel(15, 0, 4, 4); /* USB1OC */
+ sg_set_pinsel(16, 1, 4, 4); /* USB1VBUS */
- sg_set_pinsel(17, 0); /* USB2OC */
- sg_set_pinsel(18, 1); /* USB2VBUS */
+ sg_set_pinsel(17, 0, 4, 4); /* USB2OC */
+ sg_set_pinsel(18, 1, 4, 4); /* USB2VBUS */
- sg_set_pinsel(19, 0); /* USB3OC */
- sg_set_pinsel(20, 1); /* USB3VBUS */
+ sg_set_pinsel(19, 0, 4, 4); /* USB3OC */
+ sg_set_pinsel(20, 1, 4, 4); /* USB3VBUS */
#endif
}
diff --git a/arch/arm/mach-uniphier/ph1-sld3/sbc_init.c b/arch/arm/mach-uniphier/ph1-sld3/sbc_init.c
index bafab4b..3e62121 100644
--- a/arch/arm/mach-uniphier/ph1-sld3/sbc_init.c
+++ b/arch/arm/mach-uniphier/ph1-sld3/sbc_init.c
@@ -41,5 +41,5 @@ void sbc_init(void)
writel(0x0200be01, SBBASE1);
}
- sg_set_pinsel(99, 1); /* GPIO26 -> EA24 */
+ sg_set_pinsel(99, 1, 4, 4); /* GPIO26 -> EA24 */
}
diff --git a/arch/arm/mach-uniphier/ph1-sld8/lowlevel_debug.S b/arch/arm/mach-uniphier/ph1-sld8/lowlevel_debug.S
index 73f0f63..3ada4c9 100644
--- a/arch/arm/mach-uniphier/ph1-sld8/lowlevel_debug.S
+++ b/arch/arm/mach-uniphier/ph1-sld8/lowlevel_debug.S
@@ -17,8 +17,8 @@ ENTRY(setup_lowlevel_debug)
init_debug_uart r0, r1, r2
/* UART Port 0 */
- set_pinsel 70, 3, r0, r1
- set_pinsel 71, 3, r0, r1
+ sg_set_pinsel 70, 3, 8, 4, r0, r1
+ sg_set_pinsel 71, 3, 8, 4, r0, r1
ldr r0, =SG_IECTRL
ldr r1, [r0]
diff --git a/arch/arm/mach-uniphier/ph1-sld8/pinctrl.c b/arch/arm/mach-uniphier/ph1-sld8/pinctrl.c
index 98da1f9..1b64414 100644
--- a/arch/arm/mach-uniphier/ph1-sld8/pinctrl.c
+++ b/arch/arm/mach-uniphier/ph1-sld8/pinctrl.c
@@ -12,31 +12,31 @@ void pin_init(void)
/* Comment format: PAD Name -> Function Name */
#ifdef CONFIG_NAND_DENALI
- sg_set_pinsel(15, 0); /* XNFRE_GB -> XNFRE_GB */
- sg_set_pinsel(16, 0); /* XNFWE_GB -> XNFWE_GB */
- sg_set_pinsel(17, 0); /* XFALE_GB -> NFALE_GB */
- sg_set_pinsel(18, 0); /* XFCLE_GB -> NFCLE_GB */
- sg_set_pinsel(19, 0); /* XNFWP_GB -> XFNWP_GB */
- sg_set_pinsel(20, 0); /* XNFCE0_GB -> XNFCE0_GB */
- sg_set_pinsel(21, 0); /* NANDRYBY0_GB -> NANDRYBY0_GB */
- sg_set_pinsel(22, 0); /* XFNCE1_GB -> XFNCE1_GB */
- sg_set_pinsel(23, 0); /* NANDRYBY1_GB -> NANDRYBY1_GB */
- sg_set_pinsel(24, 0); /* NFD0_GB -> NFD0_GB */
- sg_set_pinsel(25, 0); /* NFD1_GB -> NFD1_GB */
- sg_set_pinsel(26, 0); /* NFD2_GB -> NFD2_GB */
- sg_set_pinsel(27, 0); /* NFD3_GB -> NFD3_GB */
- sg_set_pinsel(28, 0); /* NFD4_GB -> NFD4_GB */
- sg_set_pinsel(29, 0); /* NFD5_GB -> NFD5_GB */
- sg_set_pinsel(30, 0); /* NFD6_GB -> NFD6_GB */
- sg_set_pinsel(31, 0); /* NFD7_GB -> NFD7_GB */
+ sg_set_pinsel(15, 0, 8, 4); /* XNFRE_GB -> XNFRE_GB */
+ sg_set_pinsel(16, 0, 8, 4); /* XNFWE_GB -> XNFWE_GB */
+ sg_set_pinsel(17, 0, 8, 4); /* XFALE_GB -> NFALE_GB */
+ sg_set_pinsel(18, 0, 8, 4); /* XFCLE_GB -> NFCLE_GB */
+ sg_set_pinsel(19, 0, 8, 4); /* XNFWP_GB -> XFNWP_GB */
+ sg_set_pinsel(20, 0, 8, 4); /* XNFCE0_GB -> XNFCE0_GB */
+ sg_set_pinsel(21, 0, 8, 4); /* NANDRYBY0_GB -> NANDRYBY0_GB */
+ sg_set_pinsel(22, 0, 8, 4); /* XFNCE1_GB -> XFNCE1_GB */
+ sg_set_pinsel(23, 0, 8, 4); /* NANDRYBY1_GB -> NANDRYBY1_GB */
+ sg_set_pinsel(24, 0, 8, 4); /* NFD0_GB -> NFD0_GB */
+ sg_set_pinsel(25, 0, 8, 4); /* NFD1_GB -> NFD1_GB */
+ sg_set_pinsel(26, 0, 8, 4); /* NFD2_GB -> NFD2_GB */
+ sg_set_pinsel(27, 0, 8, 4); /* NFD3_GB -> NFD3_GB */
+ sg_set_pinsel(28, 0, 8, 4); /* NFD4_GB -> NFD4_GB */
+ sg_set_pinsel(29, 0, 8, 4); /* NFD5_GB -> NFD5_GB */
+ sg_set_pinsel(30, 0, 8, 4); /* NFD6_GB -> NFD6_GB */
+ sg_set_pinsel(31, 0, 8, 4); /* NFD7_GB -> NFD7_GB */
#endif
#ifdef CONFIG_USB_EHCI_UNIPHIER
- sg_set_pinsel(41, 0); /* USB0VBUS -> USB0VBUS */
- sg_set_pinsel(42, 0); /* USB0OD -> USB0OD */
- sg_set_pinsel(43, 0); /* USB1VBUS -> USB1VBUS */
- sg_set_pinsel(44, 0); /* USB1OD -> USB1OD */
- /* sg_set_pinsel(114, 1); */ /* TXD1 -> USB2VBUS (shared with UART) */
- /* sg_set_pinsel(115, 1); */ /* RXD1 -> USB2OD */
+ sg_set_pinsel(41, 0, 8, 4); /* USB0VBUS -> USB0VBUS */
+ sg_set_pinsel(42, 0, 8, 4); /* USB0OD -> USB0OD */
+ sg_set_pinsel(43, 0, 8, 4); /* USB1VBUS -> USB1VBUS */
+ sg_set_pinsel(44, 0, 8, 4); /* USB1OD -> USB1OD */
+ /* sg_set_pinsel(114, 1, 8, 4); */ /* TXD1 -> USB2VBUS (shared with UART) */
+ /* sg_set_pinsel(115, 1, 8, 4); */ /* RXD1 -> USB2OD */
#endif
}
--
1.9.1
More information about the U-Boot
mailing list