[U-Boot] [PATCH V3] dm: gpio: pca953x: introduce driver model support for pca953x

Michal Simek michal.simek at xilinx.com
Thu Apr 14 14:50:01 CEST 2016


On 14.4.2016 14:29, Peng Fan wrote:
> Introduce a new driver that supports driver model for pca953x.
> The pca953x chips are used as I2C I/O expanders.
> This driver is designed to support the following chips:
> "
> 4 bits: pca9536, pca9537
> 8 bits: max7310, max7315, pca6107, pca9534, pca9538, pca9554,
>         pca9556, pca9557, pca9574, tca6408, xra1202
> 16 bits: max7312, max7313, pca9535, pca9539, pca9555, pca9575,
>          tca6416
> 24 bits: tca6424
> 40 bits: pca9505, pca9698
> "
> But for now this driver only supports max 24 bits and pca953x compatible
> chips. pca957x compatible chips are not supported now.
> These can be addressed when we need to add such support for the different
> chips.
> This driver has been tested on i.MX6 SoloX Sabreauto board with max7310
> i2c expander using gpio command as following:
> 
> =>gpio status -a
> Bank gpio at 30_:
> gpio at 30_0: input: 1 [ ]
> 
> => dm tree:
>  i2c         [   ]    |   |   `-- i2c at 021a8000
>  gpio        [   ]    |   |       |-- gpio at 30
>  gpio        [   ]    |   |       `-- gpio at 32
> 
> Signed-off-by: Peng Fan <van.freenix at gmail.com>
> Cc: Simon Glass <sjg at chromium.org>
> Cc: Masahiro Yamada <yamada.masahiro at socionext.com>
> Cc: Wenyou Yang <wenyou.yang at atmel.com>
> Cc: Daniel Schwierzeck <daniel.schwierzeck at gmail.com>
> Cc: Purna Chandra Mandal <purna.mandal at microchip.com>
> Cc: Thomas Chou <thomas at wytron.com.tw>
> Cc: Bhuvanchandra DV <bhuvanchandra.dv at toradex.com>
> Cc: Andrea Scian <andrea.scian at dave.eu>
> Cc: Michal Simek <michal.simek at xilinx.com>
> Cc: Stefano Babic <sbabic at denx.de>
> Cc: Fabio Estevam <fabio.estevam at nxp.com>
> Acked-by: Simon Glass <sjg at chromium.org>
> Tested-by: Michal Simek <michal.simek at xilinx.com> #on ZynqMP zcu102
> ---
> 
> V3:
>  Add Michal's tested by
>  Take Michal's suggestion, use hex vaule for gpio@[x].
> 
> V2:
>  change bank name according to Simon's comments.
> 
>  drivers/gpio/Kconfig        |  22 +++
>  drivers/gpio/Makefile       |   2 +
>  drivers/gpio/pca953x_gpio.c | 349 ++++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 373 insertions(+)
>  create mode 100644 drivers/gpio/pca953x_gpio.c
> 
> diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
> index 2311309..8ff657c 100644
> --- a/drivers/gpio/Kconfig
> +++ b/drivers/gpio/Kconfig
> @@ -112,4 +112,26 @@ config MVEBU_GPIO
>  	help
>  	  Say yes here to support Marvell MVEBU (Armada XP/38x) GPIOs.
>  
> +config DM_PCA953X
> +	bool "PCA95[357]x, PCA9698, TCA64xx, and MAX7310 I/O ports"
> +	depends on DM_GPIO
> +	help
> +	  Say yes here to provide access to several register-oriented
> +	  SMBus I/O expanders, made mostly by NXP or TI.  Compatible
> +	  models include:
> +
> +	  4 bits:	pca9536, pca9537
> +
> +	  8 bits:	max7310, max7315, pca6107, pca9534, pca9538, pca9554,
> +			pca9556, pca9557, pca9574, tca6408, xra1202
> +
> +	  16 bits:	max7312, max7313, pca9535, pca9539, pca9555, pca9575,
> +			tca6416
> +
> +	  24 bits:	tca6424
> +
> +	  40 bits:	pca9505, pca9698
> +
> +	  Now, max 24 bits chips and PCA953X compatible chips are
> +	  supported
>  endmenu
> diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
> index ea6e2ed..a7a466c 100644
> --- a/drivers/gpio/Makefile
> +++ b/drivers/gpio/Makefile
> @@ -11,6 +11,8 @@ obj-$(CONFIG_AXP_GPIO)		+= axp_gpio.o
>  endif
>  obj-$(CONFIG_DM_GPIO)		+= gpio-uclass.o
>  
> +obj-$(CONFIG_DM_PCA953X)	+= pca953x_gpio.o
> +
>  obj-$(CONFIG_AT91_GPIO)	+= at91_gpio.o
>  obj-$(CONFIG_ATMEL_PIO4)	+= atmel_pio4.o
>  obj-$(CONFIG_INTEL_ICH6_GPIO)	+= intel_ich6_gpio.o
> diff --git a/drivers/gpio/pca953x_gpio.c b/drivers/gpio/pca953x_gpio.c
> new file mode 100644
> index 0000000..1eeb4c8
> --- /dev/null
> +++ b/drivers/gpio/pca953x_gpio.c
> @@ -0,0 +1,349 @@
> +/*
> + * Take linux kernel driver drivers/gpio/gpio-pca953x.c for reference.
> + *
> + * Copyright (C) 2016 Peng Fan <van.freenix at gmail.com>
> + *
> + * SPDX-License-Identifier:	GPL-2.0+
> + *
> + */
> +
> +/*
> + * Note:
> + * The driver's compatible table is borrowed from Linux Kernel,
> + * but now max supported gpio pins is 24 and only PCA953X_TYPE
> + * is supported. PCA957X_TYPE is not supported now.
> + * Also the Polarity Inversion feature is not supported now.
> + *
> + * TODO:
> + * 1. Support PCA957X_TYPE
> + * 2. Support max 40 gpio pins
> + * 3. Support Plolarity Inversion
> + */
> +
> +#include <common.h>
> +#include <errno.h>
> +#include <dm.h>
> +#include <fdtdec.h>
> +#include <i2c.h>
> +#include <malloc.h>
> +#include <asm/gpio.h>
> +#include <asm/io.h>
> +#include <dt-bindings/gpio/gpio.h>
> +
> +#define PCA953X_INPUT           0
> +#define PCA953X_OUTPUT          1
> +#define PCA953X_INVERT          2
> +#define PCA953X_DIRECTION       3
> +
> +#define PCA_GPIO_MASK           0x00FF
> +#define PCA_INT                 0x0100
> +#define PCA953X_TYPE            0x1000
> +#define PCA957X_TYPE            0x2000
> +#define PCA_TYPE_MASK           0xF000
> +#define PCA_CHIP_TYPE(x)        ((x) & PCA_TYPE_MASK)
> +
> +enum {
> +	PCA953X_DIRECTION_IN,
> +	PCA953X_DIRECTION_OUT,
> +};
> +
> +#define MAX_BANK 3
> +#define BANK_SZ 8
> +
> +/*
> + * struct pca953x_info - Data for pca953x
> + *
> + * @dev: udevice structure for the device
> + * @addr: i2c slave address
> + * @invert: Polarity inversion or not
> + * @gpio_count: the number of gpio pins that the device supports
> + * @chip_type: indicate the chip type,PCA953X or PCA957X
> + * @bank_count: the number of banks that the device supports
> + * @reg_output: array to hold the value of output registers
> + * @reg_direction: array to hold the value of direction registers
> + */
> +struct pca953x_info {
> +	struct udevice *dev;
> +	unsigned int addr;
> +	unsigned int invert;
> +	unsigned int gpio_count;
> +	unsigned int chip_type;
> +	unsigned int bank_count;
> +	u8 reg_output[MAX_BANK];
> +	u8 reg_direction[MAX_BANK];
> +};
> +
> +static int pca953x_write_single(struct udevice *dev, int reg, u8 val,
> +				int offset)
> +{
> +	struct pca953x_info *info = dev_get_platdata(dev);
> +	int bank_shift = fls((info->gpio_count - 1) / BANK_SZ);
> +	int off = offset / BANK_SZ;
> +	int ret = 0;
> +
> +	ret = dm_i2c_write(dev, (reg << bank_shift) + off, &val, 1);
> +	if (ret) {
> +		dev_err(dev, "%s error\n", __func__);
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static int pca953x_read_single(struct udevice *dev, int reg, u8 *val,
> +			       int offset)
> +{
> +	struct pca953x_info *info = dev_get_platdata(dev);
> +	int bank_shift = fls((info->gpio_count - 1) / BANK_SZ);
> +	int off = offset / BANK_SZ;
> +	int ret;
> +	u8 byte;
> +
> +	ret = dm_i2c_read(dev, (reg << bank_shift) + off, &byte, 1);
> +	if (ret) {
> +		dev_err(dev, "%s error\n", __func__);
> +		return ret;
> +	}
> +
> +	*val = byte;
> +
> +	return 0;
> +}
> +
> +static int pca953x_read_regs(struct udevice *dev, int reg, u8 *val)
> +{
> +	struct pca953x_info *info = dev_get_platdata(dev);
> +	int ret = 0;
> +
> +	if (info->gpio_count <= 8) {
> +		ret = dm_i2c_read(dev, reg, val, 1);
> +	} else if (info->gpio_count <= 16) {
> +		ret = dm_i2c_read(dev, reg << 1, val, info->bank_count);
> +	} else {
> +		dev_err(dev, "Unsupported now\n");
> +		return -EINVAL;
> +	}
> +
> +	return ret;
> +}
> +
> +static int pca953x_is_output(struct udevice *dev, int offset)
> +{
> +	struct pca953x_info *info = dev_get_platdata(dev);
> +
> +	int bank = offset / BANK_SZ;
> +	int off = offset % BANK_SZ;
> +
> +	/*0: output; 1: input */
> +	return !(info->reg_direction[bank] & (1 << off));
> +}
> +
> +static int pca953x_get_value(struct udevice *dev, unsigned offset)
> +{
> +	int ret;
> +	u8 val = 0;
> +
> +	ret = pca953x_read_single(dev, PCA953X_INPUT, &val, offset);
> +	if (ret)
> +		return ret;
> +
> +	return (val >> offset) & 0x1;
> +}
> +
> +static int pca953x_set_value(struct udevice *dev, unsigned offset,
> +			     int value)
> +{
> +	struct pca953x_info *info = dev_get_platdata(dev);
> +	int bank = offset / BANK_SZ;
> +	int off = offset % BANK_SZ;
> +	u8 val;
> +	int ret;
> +
> +	if (value)
> +		val = info->reg_output[bank] | (1 << off);
> +	else
> +		val = info->reg_output[bank] & ~(1 << off);
> +
> +	ret = pca953x_write_single(dev, PCA953X_OUTPUT, val, offset);
> +	if (ret)
> +		return ret;
> +
> +	info->reg_output[bank] = val;
> +
> +	return 0;
> +}
> +
> +static int pca953x_set_direction(struct udevice *dev, unsigned offset, int dir)
> +{
> +	struct pca953x_info *info = dev_get_platdata(dev);
> +	int bank = offset / BANK_SZ;
> +	int off = offset % BANK_SZ;
> +	u8 val;
> +	int ret;
> +
> +	if (dir == PCA953X_DIRECTION_IN)
> +		val = info->reg_direction[bank] | (1 << off);
> +	else
> +		val = info->reg_direction[bank] & ~(1 << off);
> +
> +	ret = pca953x_write_single(dev, PCA953X_DIRECTION, val, offset);
> +	if (ret)
> +		return ret;
> +
> +	info->reg_direction[bank] = val;
> +
> +	return 0;
> +}
> +
> +static int pca953x_direction_input(struct udevice *dev, unsigned offset)
> +{
> +	return pca953x_set_direction(dev, offset, PCA953X_DIRECTION_IN);
> +}
> +
> +static int pca953x_direction_output(struct udevice *dev, unsigned offset,
> +				    int value)
> +{
> +	/* Configure output value. */
> +	pca953x_set_value(dev, offset, value);
> +
> +	/* Configure direction as output. */
> +	pca953x_set_direction(dev, offset, PCA953X_DIRECTION_OUT);
> +
> +	return 0;
> +}
> +
> +static int pca953x_get_function(struct udevice *dev, unsigned offset)
> +{
> +	if (pca953x_is_output(dev, offset))
> +		return GPIOF_OUTPUT;
> +	else
> +		return GPIOF_INPUT;
> +}
> +
> +static int pca953x_xlate(struct udevice *dev, struct gpio_desc *desc,
> +			 struct fdtdec_phandle_args *args)
> +{
> +	desc->offset = args->args[0];
> +	desc->flags = args->args[1] & GPIO_ACTIVE_LOW ? GPIOD_ACTIVE_LOW : 0;
> +
> +	return 0;
> +}
> +
> +static const struct dm_gpio_ops pca953x_ops = {
> +	.direction_input	= pca953x_direction_input,
> +	.direction_output	= pca953x_direction_output,
> +	.get_value		= pca953x_get_value,
> +	.set_value		= pca953x_set_value,
> +	.get_function		= pca953x_get_function,
> +	.xlate			= pca953x_xlate,
> +};
> +
> +static int pca953x_probe(struct udevice *dev)
> +{
> +	struct pca953x_info *info = dev_get_platdata(dev);
> +	struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev);
> +	struct dm_i2c_chip *chip = dev_get_parent_platdata(dev);
> +	char name[32], *str;
> +	fdt_addr_t addr;
> +	ulong driver_data;
> +	int ret;
> +
> +	if (!info) {
> +		dev_err(dev, "platdata not ready\n");
> +		return -ENOMEM;
> +	}
> +
> +	if (!chip) {
> +		dev_err(dev, "i2c not ready\n");
> +		return -ENODEV;
> +	}
> +
> +	addr = dev_get_addr(dev);


addr = fdtdec_get_int(gd->fdt_blob, dev->of_offset, "reg", 0);

Please use this here based on that thread with Przemyslaw.

Thanks,
Michal



More information about the U-Boot mailing list