[U-Boot] [PATCH] arm: Fix SCFG ICID reg addresses
Vincent Siles
vincent.siles at provenrun.com
Thu Apr 21 09:53:23 CEST 2016
Hi !
On 20-04-16 09:53:32, York Sun wrote:
> On 04/12/2016 05:28 AM, Vincent Siles wrote:
> > On the LS102x boards, in order to initialize the ICID values of masters,
> > the dev_stream_id array holds absolute offsets from the base of SCFG.
> >
> > In ls102xa_config_ssmu_stream_id, the base pointer is cast to uint32_t *
> > before adding the offset, leading to an invalid address. Casting it to
> > unsigned char * solves the issue.
> >
> > Also minor cosmetic renaming of uint32_t into u32 to be consistent in
> > the whole file.
> >
> > Signed-off-by: Vincent Siles <vincent.siles at provenrun.com>
> > ---
> >
> > board/freescale/common/ls102xa_stream_id.c | 6 +++---
> > 1 file changed, 3 insertions(+), 3 deletions(-)
> >
> > diff --git a/board/freescale/common/ls102xa_stream_id.c b/board/freescale/common/ls102xa_stream_id.c
> > index f434269..2a4ef3e 100644
> > --- a/board/freescale/common/ls102xa_stream_id.c
> > +++ b/board/freescale/common/ls102xa_stream_id.c
> > @@ -10,11 +10,11 @@
> >
> > void ls102xa_config_smmu_stream_id(struct smmu_stream_id *id, uint32_t num)
> > {
> > - uint32_t *scfg = (uint32_t *)CONFIG_SYS_FSL_SCFG_ADDR;
> > + unsigned char *scfg = (unsigned char *)CONFIG_SYS_FSL_SCFG_ADDR;
> > int i;
> >
> > for (i = 0; i < num; i++)
> > - out_be32(scfg + id[i].offset, id[i].stream_id);
> > + out_be32((u32 *)(scfg + id[i].offset), id[i].stream_id);
> > }
> >
> > void ls1021x_config_caam_stream_id(struct liodn_id_table *tbl, int size)
> > @@ -28,6 +28,6 @@ void ls1021x_config_caam_stream_id(struct liodn_id_table *tbl, int size)
> > else
> > liodn = tbl[i].id[0];
> >
> > - out_le32((uint32_t *)(tbl[i].reg_offset), liodn);
> > + out_le32((u32 *)(tbl[i].reg_offset), liodn);
> > }
> > }
> >
>
> If the size of the pointer is an issue, maybe you ca use "void *"? Can you check
> if "struct ccsr_scfg" should/can be used?
>
> York
By using the 'struct ccsr_scfg' type we won't be able to have the same
kind of loop. Since the code is board dependent, I'm not sure it really
matters.
Here what I would do instead. Tell me which style do you prefer.
Best,
Vincent
---
diff --git a/arch/arm/cpu/armv7/ls102xa/soc.c b/arch/arm/cpu/armv7/ls102xa/soc.c
index b1b0c71..9c78efc 100644
--- a/arch/arm/cpu/armv7/ls102xa/soc.c
+++ b/arch/arm/cpu/armv7/ls102xa/soc.c
@@ -30,21 +30,21 @@ struct liodn_id_table sec_liodn_tbl[] = {
SET_SEC_DECO_LIODN_ENTRY(7, 0x10, 0x10),
};
-struct smmu_stream_id dev_stream_id[] = {
- { 0x100, 0x01, "ETSEC MAC1" },
- { 0x104, 0x02, "ETSEC MAC2" },
- { 0x108, 0x03, "ETSEC MAC3" },
- { 0x10c, 0x04, "PEX1" },
- { 0x110, 0x05, "PEX2" },
- { 0x114, 0x06, "qDMA" },
- { 0x118, 0x07, "SATA" },
- { 0x11c, 0x08, "USB3" },
- { 0x120, 0x09, "QE" },
- { 0x124, 0x0a, "eSDHC" },
- { 0x128, 0x0b, "eMA" },
- { 0x14c, 0x0c, "2D-ACE" },
- { 0x150, 0x0d, "USB2" },
- { 0x18c, 0x0e, "DEBUG" },
+struct smmu_stream_id dev_stream_id = {
+ .mac1 = 0x01,
+ .mac2 = 0x02,
+ .mac3 = 0x03,
+ .pex1 = 0x04,
+ .pex2 = 0x05,
+ .dma = 0x06,
+ .sata = 0x07,
+ .usb3 = 0x08,
+ .qe = 0x09,
+ .sdhc = 0x0a,
+ .adma = 0x0b,
+ .dcu = 0x0c,
+ .usb2 = 0x0d,
+ .debug = 0x0e
};
unsigned int get_soc_major_rev(void)
@@ -131,8 +131,7 @@ int ls102xa_smmu_stream_id_init(void)
ls1021x_config_caam_stream_id(sec_liodn_tbl,
ARRAY_SIZE(sec_liodn_tbl));
- ls102xa_config_smmu_stream_id(dev_stream_id,
- ARRAY_SIZE(dev_stream_id));
+ ls102xa_config_smmu_stream_id(&dev_stream_id);
return 0;
}
diff --git a/arch/arm/include/asm/arch-ls102xa/ls102xa_stream_id.h b/arch/arm/include/asm/arch-ls102xa/ls102xa_stream_id.h
index fa571b3..3815673 100644
--- a/arch/arm/include/asm/arch-ls102xa/ls102xa_stream_id.h
+++ b/arch/arm/include/asm/arch-ls102xa/ls102xa_stream_id.h
@@ -64,11 +64,22 @@ struct liodn_id_table {
};
struct smmu_stream_id {
- uint16_t offset;
- uint16_t stream_id;
- char dev_name[32];
+ uint16_t mac1;
+ uint16_t mac2;
+ uint16_t mac3;
+ uint16_t pex1;
+ uint16_t pex2;
+ uint16_t dma;
+ uint16_t sata;
+ uint16_t usb3;
+ uint16_t qe;
+ uint16_t sdhc;
+ uint16_t adma;
+ uint16_t dcu;
+ uint16_t usb2;
+ uint16_t debug;
};
void ls1021x_config_caam_stream_id(struct liodn_id_table *tbl, int size);
-void ls102xa_config_smmu_stream_id(struct smmu_stream_id *id, uint32_t num);
+void ls102xa_config_smmu_stream_id(struct smmu_stream_id *id);
#endif
diff --git a/board/freescale/common/ls102xa_stream_id.c b/board/freescale/common/ls102xa_stream_id.c
index f434269..941f22d 100644
--- a/board/freescale/common/ls102xa_stream_id.c
+++ b/board/freescale/common/ls102xa_stream_id.c
@@ -7,14 +7,25 @@
#include <common.h>
#include <asm/io.h>
#include <asm/arch/ls102xa_stream_id.h>
+#include <asm/arch/immap_ls102xa.h>
-void ls102xa_config_smmu_stream_id(struct smmu_stream_id *id, uint32_t num)
+void ls102xa_config_smmu_stream_id(struct smmu_stream_id *id)
{
- uint32_t *scfg = (uint32_t *)CONFIG_SYS_FSL_SCFG_ADDR;
- int i;
-
- for (i = 0; i < num; i++)
- out_be32(scfg + id[i].offset, id[i].stream_id);
+ struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
+ scfg->mac1_streamid = id->mac1;
+ scfg->mac2_streamid = id->mac2;
+ scfg->mac3_streamid = id->mac3;
+ scfg->pex1_streamid = id->pex1;
+ scfg->pex2_streamid = id->pex2;
+ scfg->dma_streamid = id->dma;
+ scfg->sata_streamid = id->sata;
+ scfg->usb3_streamid = id->usb3;
+ scfg->qe_streamid = id->qe;
+ scfg->sdhc_streamid = id->sdhc;
+ scfg->adma_streamid = id->adma;
+ scfg->dcu_streamid = id->dcu;
+ scfg->usb2_streamid = id->usb2;
+ scfg->debug_streamid = id->debug;
}
void ls1021x_config_caam_stream_id(struct liodn_id_table *tbl, int size)
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 473 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20160421/8a9422a8/attachment.sig>
More information about the U-Boot
mailing list