[U-Boot] [v2, 4/5] mmc: add workaround for eSDHC erratum A009620

[Yangbo Lu]

Erratum Title:
Data timeout error not getting set in case of command with busy
response (R1b) as well as for busy period after last write block
transfer.

Description:
In the event that a busy timeout occurs for a command with a busy
response (e.g. R1b response) as well as busy period after the last
write block, the eSDHC does not set the IRQSTAT[DTOE] bit or the
IRQSTAT[TC]. Therefore, the current command transfer is never completed.

Workaround:
Workaround for CMD with busy:
Don't set the XFRTYP[RSP]=2'b11 for commands with busy response and
poll the busy status of the card from the PRSSTAT[DLSL]

Workaround for busy period after last write block:
1. After the command completion interrupt (IRQSTAT[CC]), wait for
   de-assertion of PRSTAT[WTA].
2. Once PRSTAT[WTA] is de-asserted, start the software timer and poll
   the busy signal (DAT0) using PRSTAT[DLSL[0]].
3. Wait for DAT0 signal to go high (which indicate transfer complete)
   or software timer expiry (which indicate data timeout error).
4. Issue soft reset for data (SYSCTL[RSTD]).
5. In case of data timeout error (detected in step 3) perform the
   error recovery.

The workaround for CMD with busy has already been applied in eSDHC
driver. This patch is to add workaround for the 2nd issue.

Signed-off-by: Yangbo Lu <yangbo.lu at nxp.com>
---
Changes for v2:
	- Split original patch into config part and mmc part
---
 drivers/mmc/fsl_esdhc.c | 26 ++++++++++++++++++++++++++
 include/fsl_esdhc.h     |  1 +
 2 files changed, 27 insertions(+)

diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c
index 80bc177..99cadae 100644
--- a/drivers/mmc/fsl_esdhc.c
+++ b/drivers/mmc/fsl_esdhc.c
@@ -482,6 +482,32 @@ esdhc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, struct mmc_data *data)
 #ifdef CONFIG_SYS_FSL_ESDHC_USE_PIO
 		esdhc_pio_read_write(mmc, data);
 #else
+#ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC_A009620
+		int timeout = 5000;
+		if (data->flags & MMC_DATA_WRITE) {
+			while (esdhc_read32(&regs->prsstat) & PRSSTAT_WTA)
+				;
+
+			/* Poll on DATA0 line for 500 ms */
+			while (!(esdhc_read32(&regs->prsstat) & PRSSTAT_DAT0)) {
+				udelay(100);
+				timeout--;
+				if (timeout <= 0) {
+					err = TIMEOUT;
+					break;
+				}
+			}
+			if (!err) {
+				esdhc_write32(&regs->sysctl,
+					      esdhc_read32(&regs->sysctl) |
+					      SYSCTL_RSTD);
+				while ((esdhc_read32(&regs->sysctl) &
+					SYSCTL_RSTD))
+					;
+			}
+			goto out;
+		}
+#endif
 		do {
 			irqstat = esdhc_read32(&regs->irqstat);
 
diff --git a/include/fsl_esdhc.h b/include/fsl_esdhc.h
index c6f4666..3f146f7 100644
--- a/include/fsl_esdhc.h
+++ b/include/fsl_esdhc.h
@@ -97,6 +97,7 @@
 #define PRSSTAT_CINS		(0x00010000)
 #define PRSSTAT_BREN		(0x00000800)
 #define PRSSTAT_BWEN		(0x00000400)
+#define PRSSTAT_WTA		(0x00000100)
 #define PRSSTAT_SDSTB		(0X00000008)
 #define PRSSTAT_DLA		(0x00000004)
 #define PRSSTAT_CICHB		(0x00000002)
-- 
2.1.0.27.g96db324