[U-Boot] [PATCH 1/2] driver/ddr/fsl: Add general MMDC driver

Shengzhou Liu Shengzhou.Liu at nxp.com
Thu Aug 11 06:43:33 CEST 2016


This patch adds basic support for Freescale MMDC(Multi Mode DDR Controller).
Currently MMDC is integrated on ARMv8 LS1012A SoC for DDR3L, there will be a
update to this driver to support more flexible configuration if new features
(DDR4, multiple controllers/chip selections, etc) are implimented in future.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu at nxp.com>
---
 Makefile                                          |   1 +
 arch/arm/include/asm/arch-fsl-layerscape/config.h |   2 +
 drivers/ddr/fsl/Makefile                          |   1 +
 drivers/ddr/fsl/fsl_mmdc.c                        | 152 ++++++++++++++++++++++
 include/fsl_mmdc.h                                |  83 +++++-------
 5 files changed, 192 insertions(+), 47 deletions(-)
 create mode 100644 drivers/ddr/fsl/fsl_mmdc.c

diff --git a/Makefile b/Makefile
index 99cc8cf..1bf6c6a 100644
--- a/Makefile
+++ b/Makefile
@@ -647,6 +647,7 @@ libs-y += drivers/power/ \
 libs-y += drivers/spi/
 libs-$(CONFIG_FMAN_ENET) += drivers/net/fm/
 libs-$(CONFIG_SYS_FSL_DDR) += drivers/ddr/fsl/
+libs-$(CONFIG_SYS_FSL_MMDC) += drivers/ddr/fsl/
 libs-$(CONFIG_ALTERA_SDRAM) += drivers/ddr/altera/
 libs-y += drivers/serial/
 libs-y += drivers/usb/dwc3/
diff --git a/arch/arm/include/asm/arch-fsl-layerscape/config.h b/arch/arm/include/asm/arch-fsl-layerscape/config.h
index b0ad4b4..478b7ab 100644
--- a/arch/arm/include/asm/arch-fsl-layerscape/config.h
+++ b/arch/arm/include/asm/arch-fsl-layerscape/config.h
@@ -18,6 +18,8 @@
 #ifndef CONFIG_LS1012A
 #define CONFIG_SYS_FSL_DDR		/* Freescale DDR driver */
 #define CONFIG_SYS_FSL_DDR_VER		FSL_DDR_VER_5_0
+#else
+#define CONFIG_SYS_FSL_MMDC		/* Freescale MMDC driver */
 #endif
 
 /*
diff --git a/drivers/ddr/fsl/Makefile b/drivers/ddr/fsl/Makefile
index 01ea862..00dea42 100644
--- a/drivers/ddr/fsl/Makefile
+++ b/drivers/ddr/fsl/Makefile
@@ -33,3 +33,4 @@ obj-$(CONFIG_SYS_FSL_DDRC_GEN3)	+= mpc85xx_ddr_gen3.o
 obj-$(CONFIG_SYS_FSL_DDR_86XX)		+= mpc86xx_ddr.o
 obj-$(CONFIG_SYS_FSL_DDRC_ARM_GEN3)	+= arm_ddr_gen3.o
 obj-$(CONFIG_SYS_FSL_DDRC_GEN4) += fsl_ddr_gen4.o
+obj-$(CONFIG_SYS_FSL_MMDC) += fsl_mmdc.o
diff --git a/drivers/ddr/fsl/fsl_mmdc.c b/drivers/ddr/fsl/fsl_mmdc.c
new file mode 100644
index 0000000..eb36cea
--- /dev/null
+++ b/drivers/ddr/fsl/fsl_mmdc.c
@@ -0,0 +1,152 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+/*
+ * Generic driver for Freescale MMDC(Multi Mode DDR Controller).
+ */
+
+#include <common.h>
+#include <fsl_mmdc.h>
+#include <asm/io.h>
+
+static void set_wait_for_bits_clear(void *ptr, u32 value, u32 bits)
+{
+	int timeout = 1000;
+
+	out_be32(ptr, value);
+
+	while (in_be32(ptr) & bits) {
+		udelay(100);
+		timeout--;
+	}
+	if (timeout <= 0)
+		printf("Error: %p wait for clear timeout.\n", ptr);
+}
+
+void mmdc_init(void)
+{
+	struct mmdc_regs *mmdc = (struct mmdc_regs *)CONFIG_SYS_FSL_DDR_ADDR;
+	unsigned int tmp;
+
+	/* 1. set configuration request */
+	out_be32(&mmdc->mdscr, MDSCR_ENABLE_CON_REQ);
+
+	/* 2. configure the desired timing parameters */
+	out_be32(&mmdc->mdotc,  CONFIG_MMDC_MDOTC);
+	out_be32(&mmdc->mdcfg0, CONFIG_MMDC_MDCFG0);
+	out_be32(&mmdc->mdcfg1, CONFIG_MMDC_MDCFG1);
+	out_be32(&mmdc->mdcfg2, CONFIG_MMDC_MDCFG2);
+
+	/* 3. configure DDR type and other miscellaneous parameters */
+	out_be32(&mmdc->mdmisc, CONFIG_MMDC_MDMISC);
+	out_be32(&mmdc->mpmur0,	MMDC_MPMUR0_FRC_MSR);
+	out_be32(&mmdc->mdrwd,  CONFIG_MMDC_MDRWD);
+	out_be32(&mmdc->mpodtctrl, CONFIG_MMDC_MPODTCTRL);
+
+	/* 4. configure the required delay while leaving reset */
+	out_be32(&mmdc->mdor,  CONFIG_MMDC_MDOR);
+
+	/* 5. configure DDR physical parameters */
+	/* set row/column address width, burst length, data bus width */
+	tmp = CONFIG_MMDC_MDCTL & ~(MDCTL_SDE0 | MDCTL_SDE1);
+	out_be32(&mmdc->mdctl, tmp);
+	/* configure address space partition */
+	out_be32(&mmdc->mdasp, CONFIG_MMDC_MDASP);
+
+	/* 6. perform a ZQ calibration - not needed here, doing in #8b */
+
+	/* 7. enable MMDC with the desired chip select */
+#if (CONFIG_CHIP_SELECTS_PER_CTRL == 1)
+		out_be32(&mmdc->mdctl, tmp | MDCTL_SDE0);
+#elif (CONFIG_CHIP_SELECTS_PER_CTRL == 2)
+		out_be32(&mmdc->mdctl, tmp | MDCTL_SDE0 | MDCTL_SDE1);
+#endif
+
+	/* 8a. dram init sequence: update MRs for ZQ, ODT, PRE, etc */
+	out_be32(&mmdc->mdscr,  CMD_ADDR_LSB_MR_ADDR(8) | MDSCR_ENABLE_CON_REQ |
+				CMD_LOAD_MODE_REG | CMD_BANK_ADDR_2);
+
+	out_be32(&mmdc->mdscr,  CMD_ADDR_LSB_MR_ADDR(0) | MDSCR_ENABLE_CON_REQ |
+				CMD_LOAD_MODE_REG | CMD_BANK_ADDR_3);
+
+	out_be32(&mmdc->mdscr,  CMD_ADDR_LSB_MR_ADDR(4) | MDSCR_ENABLE_CON_REQ |
+				CMD_LOAD_MODE_REG | CMD_BANK_ADDR_1);
+
+	out_be32(&mmdc->mdscr,  CMD_ADDR_MSB_MR_OP(0x19) |
+				CMD_ADDR_LSB_MR_ADDR(0x30) |
+				MDSCR_ENABLE_CON_REQ |
+				CMD_LOAD_MODE_REG | CMD_BANK_ADDR_0);
+
+	/* 8b. ZQ calibration */
+	out_be32(&mmdc->mdscr,  CMD_ADDR_MSB_MR_OP(0x4) | MDSCR_ENABLE_CON_REQ |
+				CMD_ZQ_CALIBRATION | CMD_BANK_ADDR_0);
+
+	set_wait_for_bits_clear(&mmdc->mpzqhwctrl, CONFIG_MMDC_MPZQHWCTRL,
+				MPZQHWCTRL_ZQ_HW_FORCE);
+
+	/* 9a. calibrations now, wr lvl */
+	out_be32(&mmdc->mdscr,  CMD_ADDR_LSB_MR_ADDR(0x84) |
+				MDSCR_ENABLE_CON_REQ |
+				CMD_LOAD_MODE_REG | CMD_BANK_ADDR_1);
+
+	out_be32(&mmdc->mdscr,  MDSCR_ENABLE_CON_REQ | MDSCR_WL_EN |
+				CMD_NORMAL);
+
+	set_wait_for_bits_clear(&mmdc->mpwlgcr, MPWLGCR_HW_WL_EN,
+				MPWLGCR_HW_WL_EN);
+
+	mdelay(1);
+
+	out_be32(&mmdc->mdscr,  CMD_ADDR_LSB_MR_ADDR(4) | MDSCR_ENABLE_CON_REQ |
+				CMD_LOAD_MODE_REG | CMD_BANK_ADDR_1);
+	out_be32(&mmdc->mdscr, MDSCR_ENABLE_CON_REQ);
+
+	mdelay(1);
+
+	/* 9b. read DQS gating calibration */
+	out_be32(&mmdc->mdscr,  CMD_ADDR_MSB_MR_OP(4) | MDSCR_ENABLE_CON_REQ |
+				CMD_PRECHARGE_BANK_OPEN | CMD_BANK_ADDR_0);
+
+	out_be32(&mmdc->mdscr,  CMD_ADDR_LSB_MR_ADDR(4) | MDSCR_ENABLE_CON_REQ |
+				CMD_LOAD_MODE_REG | CMD_BANK_ADDR_3);
+
+	out_be32(&mmdc->mppdcmpr2, MPPDCMPR2_MPR_COMPARE_EN);
+	/* set absolute read delay offset for bytes */
+	out_be32(&mmdc->mprddlctl, CONFIG_MMDC_MPRDDLCTL);
+
+	set_wait_for_bits_clear(&mmdc->mpdgctrl0,
+				AUTO_RD_DQS_GATING_CALIBRATION_EN,
+				AUTO_RD_DQS_GATING_CALIBRATION_EN);
+
+	out_be32(&mmdc->mdscr, (MDSCR_ENABLE_CON_REQ | CMD_LOAD_MODE_REG |
+				CMD_BANK_ADDR_3));
+
+	/* 9c. read calibration */
+	out_be32(&mmdc->mdscr,  CMD_ADDR_MSB_MR_OP(4) | MDSCR_ENABLE_CON_REQ |
+				CMD_PRECHARGE_BANK_OPEN | CMD_BANK_ADDR_0);
+	out_be32(&mmdc->mdscr,  CMD_ADDR_LSB_MR_ADDR(4) | MDSCR_ENABLE_CON_REQ |
+				CMD_LOAD_MODE_REG | CMD_BANK_ADDR_3);
+	out_be32(&mmdc->mppdcmpr2,  MPPDCMPR2_MPR_COMPARE_EN);
+	set_wait_for_bits_clear(&mmdc->mprddlhwctl,
+				MPRDDLHWCTL_AUTO_RD_CALIBRATION_EN,
+				MPRDDLHWCTL_AUTO_RD_CALIBRATION_EN);
+
+	out_be32(&mmdc->mdscr, (MDSCR_ENABLE_CON_REQ | CMD_LOAD_MODE_REG |
+				CMD_BANK_ADDR_3));
+
+	/* 10. configure power-down, self-refresh entry, exit parameters */
+	out_be32(&mmdc->mdpdc, CONFIG_MMDC_MDPDC);
+	out_be32(&mmdc->mapsr, MMDC_MAPSR_PWR_SAV_CTRL_STAT);
+
+	/* 11. ZQ config again? do nothing here */
+
+	/* 12. refresh scheme */
+	set_wait_for_bits_clear(&mmdc->mdref, CONFIG_MMDC_MDREF,
+				MDREF_START_REFRESH);
+
+	/* 13. disable CON_REQ */
+	out_be32(&mmdc->mdscr, MDSCR_DISABLE_CFG_REQ);
+}
diff --git a/include/fsl_mmdc.h b/include/fsl_mmdc.h
index a939d89..a10e40c 100644
--- a/include/fsl_mmdc.h
+++ b/include/fsl_mmdc.h
@@ -7,63 +7,39 @@
 #ifndef FSL_MMDC_H
 #define FSL_MMDC_H
 
-#define CONFIG_SYS_MMDC_CORE_ODT_TIMING		0x12554000
-#define CONFIG_SYS_MMDC_CORE_TIMING_CFG_0	0xbabf7954
-#define CONFIG_SYS_MMDC_CORE_TIMING_CFG_1	0xff328f64
-#define CONFIG_SYS_MMDC_CORE_TIMING_CFG_2	0x01ff00db
-
-#define CONFIG_SYS_MMDC_CORE_MISC		0x00001680
-#define CONFIG_SYS_MMDC_PHY_MEASURE_UNIT	0x00000800
-#define CONFIG_SYS_MMDC_CORE_RDWR_CMD_DELAY	0x00002000
-#define CONFIG_SYS_MMDC_PHY_ODT_CTRL		0x0000022a
-
-#define CONFIG_SYS_MMDC_CORE_OUT_OF_RESET_DELAY	0x00bf1023
-
-#define CONFIG_SYS_MMDC_CORE_ADDR_PARTITION	0x0000007f
-
-#define CONFIG_SYS_MMDC_PHY_ZQ_HW_CTRL		0xa1390003
-
-#define	FORCE_ZQ_AUTO_CALIBRATION		(0x1 << 16)
-
-/* PHY Write Leveling Configuration and Error Status (MPWLGCR) */
-#define WR_LVL_HW_EN				0x00000001
+/* PHY Write Leveling Configuration and Error Status Register (MPWLGCR) */
+#define MPWLGCR_HW_WL_EN		(1 << 0)
 
 /* PHY Pre-defined Compare and CA delay-line Configuration (MPPDCMPR2) */
-#define MPR_COMPARE_EN				0x00000001
+#define MPPDCMPR2_MPR_COMPARE_EN	(1 << 0)
 
-#define CONFIG_SYS_MMDC_PHY_RD_DLY_LINES_CFG	0x40404040
 
 /* MMDC PHY Read DQS gating control register 0 (MPDGCTRL0) */
-#define AUTO_RD_DQS_GATING_CALIBRATION_EN	0x10000000
+#define AUTO_RD_DQS_GATING_CALIBRATION_EN	(1 << 28)
 
 /* MMDC PHY Read Delay HW Calibration Control Register (MPRDDLHWCTL) */
-#define AUTO_RD_CALIBRATION_EN			0x00000010
-
-#define CONFIG_SYS_MMDC_CORE_PWR_DOWN_CTRL	0x00030035
+#define MPRDDLHWCTL_AUTO_RD_CALIBRATION_EN	(1 << 4)
 
-#define CONFIG_SYS_MMDC_CORE_PWR_SAV_CTRL_STAT	0x00001067
+/* MMDC Core Power Saving Control and Status Register (MMDC_MAPSR) */
+#define MMDC_MAPSR_PWR_SAV_CTRL_STAT	0x00001067
 
-#define CONFIG_SYS_MMDC_CORE_REFRESH_CTL	0x0f3c8000
-
-#define START_REFRESH				0x00000001
+/* MMDC Core Refresh Control Register (MMDC_MDREF) */
+#define MDREF_START_REFRESH	(1 << 0)
 
 /* MMDC Core Special Command Register (MDSCR) */
-#define CMD_ADDR_MSB_MR_OP(x)   (x << 24)
-
-#define  CMD_ADDR_LSB_MR_ADDR(x)    (x << 16)
-
-#define DISABLE_CFG_REQ		0x0
-#define CONFIGURATION_REQ	(0x1  << 15)
-#define WL_EN			(0x1  << 9)
-
-#define	CMD_NORMAL		(0x0 << 4)
-#define	CMD_PRECHARGE		(0x1 << 4)
-#define	CMD_AUTO_REFRESH	(0x2 << 4)
-#define	CMD_LOAD_MODE_REG	(0x3 << 4)
-#define	CMD_ZQ_CALIBRATION	(0x4 << 4)
-#define	CMD_PRECHARGE_BANK_OPEN	(0x5 << 4)
-#define	CMD_MRR			(0x6 << 4)
-
+#define CMD_ADDR_MSB_MR_OP(x)	(x << 24)
+#define CMD_ADDR_LSB_MR_ADDR(x) (x << 16)
+#define MDSCR_DISABLE_CFG_REQ   (0 << 15)
+#define MDSCR_ENABLE_CON_REQ	(1 << 15)
+#define MDSCR_CON_ACK		(1 << 14)
+#define MDSCR_WL_EN		(1 << 9)
+#define	CMD_NORMAL		(0 << 4)
+#define	CMD_PRECHARGE		(1 << 4)
+#define	CMD_AUTO_REFRESH	(2 << 4)
+#define	CMD_LOAD_MODE_REG	(3 << 4)
+#define	CMD_ZQ_CALIBRATION	(4 << 4)
+#define	CMD_PRECHARGE_BANK_OPEN	(5 << 4)
+#define	CMD_MRR			(6 << 4)
 #define CMD_BANK_ADDR_0		0x0
 #define CMD_BANK_ADDR_1		0x1
 #define CMD_BANK_ADDR_2		0x2
@@ -73,8 +49,19 @@
 #define CMD_BANK_ADDR_6		0x6
 #define CMD_BANK_ADDR_7		0x7
 
+/* MMDC Core Control Register (MDCTL) */
+#define MDCTL_SDE0		(1 << 31)
+#define MDCTL_SDE1		(1 << 30)
+
+/* MMDC PHY ZQ HW control register (MMDC_MPZQHWCTRL) */
+#define MPZQHWCTRL_ZQ_HW_FORCE	(1 << 16)
+
+/* MMDC PHY Measure Unit Register (MMDC_MPMUR0) */
+#define MMDC_MPMUR0_FRC_MSR	(1 << 11)
+
+
 /* MMDC Registers */
-struct mmdc_p_regs {
+struct mmdc_regs {
 	u32 mdctl;
 	u32 mdpdc;
 	u32 mdotc;
@@ -157,4 +144,6 @@ struct mmdc_p_regs {
 	u32 mpdccr;
 };
 
+void mmdc_init(void);
+
 #endif /* FSL_MMDC_H */
-- 
2.1.0.27.g96db324



More information about the U-Boot mailing list