[U-Boot] [PATCH 16/17] arm: mvebu: Add gdsys ControlCenter-Compact board
Stefan Roese
sr at denx.de
Thu Dec 1 10:57:50 CET 2016
On 23.11.2016 16:12, Mario Six wrote:
> From: Dirk Eibach <dirk.eibach at gdsys.cc>
>
> The gdsys ControlCenter Digital board is based on a Marvell Armada 38x
> SOC.
>
> It boots from SPI-Flash but can be configured to boot from SD-card for
> factory programming and testing.
>
> On board peripherals include:
> - 2 x GbE
> - Xilinx Kintex-7 FPGA connected via PCIe
> - mSATA
> - USB3 host
> - Atmel TPM
>
> Signed-off-by: Dirk Eibach <dirk.eibach at gdsys.cc>
> Signed-off-by: Mario Six <mario.six at gdsys.cc>
> ---
> arch/arm/Kconfig | 1 +
> arch/arm/dts/Makefile | 3 +-
> arch/arm/dts/controlcenterdc.dts | 629 +++++++++++++++++++++++++++++++++
Could you perhaps rename this file (and board name as well?) to
something like "armada-38x-controlcenterdc*" instead? Its much easier
to match the files to the architecture this way. And until now, all
Armada XP / 38x (etc) files match this rule.
> arch/arm/mach-mvebu/Kconfig | 4 +
> board/gdsys/38x/.gitignore | 1 +
Perhaps better s/38x/a38x for "Armada"?
> board/gdsys/38x/Kconfig | 42 +++
> board/gdsys/38x/MAINTAINERS | 7 +
> board/gdsys/38x/Makefile | 30 ++
> board/gdsys/38x/README | 18 +
> board/gdsys/38x/controlcenterdc.c | 717 ++++++++++++++++++++++++++++++++++++++
> board/gdsys/38x/dt_helpers.c | 60 ++++
> board/gdsys/38x/dt_helpers.h | 16 +
> board/gdsys/38x/hre.c | 517 +++++++++++++++++++++++++++
> board/gdsys/38x/hre.h | 38 ++
> board/gdsys/38x/keyprogram.c | 158 +++++++++
> board/gdsys/38x/keyprogram.h | 14 +
> board/gdsys/38x/kwbimage.cfg.in | 12 +
> board/gdsys/38x/spl.c | 21 ++
> configs/controlcenterdc_defconfig | 54 +++
> include/configs/controlcenterdc.h | 244 +++++++++++++
> 20 files changed, 2585 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/dts/controlcenterdc.dts
> create mode 100644 board/gdsys/38x/.gitignore
> create mode 100644 board/gdsys/38x/Kconfig
> create mode 100644 board/gdsys/38x/MAINTAINERS
> create mode 100644 board/gdsys/38x/Makefile
> create mode 100644 board/gdsys/38x/README
> create mode 100644 board/gdsys/38x/controlcenterdc.c
> create mode 100644 board/gdsys/38x/dt_helpers.c
> create mode 100644 board/gdsys/38x/dt_helpers.h
> create mode 100644 board/gdsys/38x/hre.c
> create mode 100644 board/gdsys/38x/hre.h
> create mode 100644 board/gdsys/38x/keyprogram.c
> create mode 100644 board/gdsys/38x/keyprogram.h
> create mode 100644 board/gdsys/38x/kwbimage.cfg.in
> create mode 100644 board/gdsys/38x/spl.c
> create mode 100644 configs/controlcenterdc_defconfig
> create mode 100644 include/configs/controlcenterdc.h
>
> diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
> index acd689b..f4c236b 100644
> --- a/arch/arm/Kconfig
> +++ b/arch/arm/Kconfig
> @@ -970,6 +970,7 @@ source "board/freescale/mx53loco/Kconfig"
> source "board/freescale/mx53smd/Kconfig"
> source "board/freescale/s32v234evb/Kconfig"
> source "board/freescale/vf610twr/Kconfig"
> +source "board/gdsys/38x/Kconfig"
> source "board/gumstix/pepper/Kconfig"
> source "board/h2200/Kconfig"
> source "board/hisilicon/hikey/Kconfig"
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 2c5b2f2..b0bd507 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -76,7 +76,8 @@ dtb-$(CONFIG_ARCH_MVEBU) += \
> armada-xp-gp.dtb \
> armada-xp-maxbcm.dtb \
> armada-xp-synology-ds414.dtb \
> - armada-xp-theadorable.dtb
> + armada-xp-theadorable.dtb \
> + controlcenterdc.dtb
>
> dtb-$(CONFIG_ARCH_UNIPHIER) += \
> uniphier-ld11-ref.dtb \
> diff --git a/arch/arm/dts/controlcenterdc.dts b/arch/arm/dts/controlcenterdc.dts
> new file mode 100644
> index 0000000..baf0171
> --- /dev/null
> +++ b/arch/arm/dts/controlcenterdc.dts
> @@ -0,0 +1,629 @@
> +/*
> + * Device Tree file for the Guntermann & Drunck ControlCenter-Compact board
> + *
> + * Copyright (C) 2016 Mario Six <mario.six at gdsys.cc>
> + *
> + * based on the Device Tree file for Marvell Armada 388 evaluation board
> + * (DB-88F6820), which is
> + *
> + * Copyright (C) 2014 Marvell
> + *
> + * Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +/dts-v1/;
> +
> +#include "armada-388.dtsi"
> +
> +&uart0 {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&uart1 {
> + u-boot,dm-pre-reloc;
> +};
> +
> +/ {
> + model = "Controlcenter Digital Compact";
> + compatible = "marvell,a385-db", "marvell,armada388",
> + "marvell,armada385", "marvell,armada380";
> +
> + chosen {
> + bootargs = "console=ttyS1,115200 earlyprintk";
> + stdout-path = "/soc/internal-regs/serial at 12100";
> + };
> +
> + aliases {
> + ethernet0 = ð0;
> + ethernet2 = ð2;
> + mdio-gpio0 = &MDIO0;
> + mdio-gpio1 = &MDIO1;
> + mdio-gpio2 = &MDIO2;
> + spi0 = &spi0;
> + spi1 = &spi1;
> + i2c0 = &I2C0;
> + i2c1 = &I2C1;
> + };
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x10000000>; /* 256 MB */
> + };
> +
> + clocks {
> + sc16isclk: sc16isclk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <11059200>;
> + };
> + };
> +
> + soc {
> + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
> + MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
> +
> + internal-regs {
> + spi0: spi at 10600 {
> + status = "okay";
> + sc16is741: sc16is741 at 0 {
> + compatible = "nxp,sc16is741";
> + reg = <0>;
> + clocks = <&sc16isclk>;
> + spi-max-frequency = <4000000>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> + };
> +
> + spi1: spi at 10680 {
> + status = "okay";
> + u-boot,dm-pre-reloc;
> + spi-flash at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "n25q016a";
> + reg = <0>; /* Chip select 0 */
> + spi-max-frequency = <108000000>;
> + };
> + spi-flash at 1 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "n25q128a11";
> + reg = <1>; /* Chip select 1 */
> + spi-max-frequency = <108000000>;
> + u-boot,dm-pre-reloc;
> + };
> + };
> +
> + I2C0: i2c at 11000 {
> + status = "okay";
> + clock-frequency = <1000000>;
> + u-boot,dm-pre-reloc;
> + PCA21: pca9698 at 21 {
> + compatible = "nxp,pca9698";
> + reg = <0x21>;
> + #gpio-cells = <2>;
> + gpio-controller;
> + };
> + PCA22: pca9698 at 22 {
> + compatible = "nxp,pca9698";
> + u-boot,dm-pre-reloc;
> + reg = <0x22>;
> + #gpio-cells = <2>;
> + gpio-controller;
> + };
> + PCA23: pca9698 at 23 {
> + compatible = "nxp,pca9698";
> + reg = <0x23>;
> + #gpio-cells = <2>;
> + gpio-controller;
> + };
> + PCA24: pca9698 at 24 {
> + compatible = "nxp,pca9698";
> + reg = <0x24>;
> + #gpio-cells = <2>;
> + gpio-controller;
> + };
> + PCA25: pca9698 at 25 {
> + compatible = "nxp,pca9698";
> + reg = <0x25>;
> + #gpio-cells = <2>;
> + gpio-controller;
> + };
> + PCA26: pca9698 at 26 {
> + compatible = "nxp,pca9698";
> + reg = <0x26>;
> + #gpio-cells = <2>;
> + gpio-controller;
> + };
> + };
> +
> + I2C1: i2c at 11100 {
> + status = "okay";
> + clock-frequency = <400000>;
> + at97sc3205t at 29 {
> + compatible = "atmel,at97sc3204t";
> + reg = <0x29>;
> + u-boot,i2c-offset-len = <0>;
> + };
> + emc2305 at 2d {
> + compatible = "smsc,emc2305";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x2d>;
> + fan at 0 {
> + reg = <0>;
> + };
> + fan at 1 {
> + reg = <1>;
> + };
> + fan at 2 {
> + reg = <2>;
> + };
> + fan at 3 {
> + reg = <3>;
> + };
> + fan at 4 {
> + reg = <4>;
> + };
> + };
> + lm77 at 48 {
> + compatible = "national,lm77";
> + reg = <0x48>;
> + };
> + ads1015 at 49 {
> + compatible = "ti,ads1015";
> + reg = <0x49>;
> + };
> + lm77 at 4a {
> + compatible = "national,lm77";
> + reg = <0x4a>;
> + };
> + ads1015 at 4b {
> + compatible = "ti,ads1015";
> + reg = <0x4b>;
> + };
> + emc2305 at 4c {
> + compatible = "smsc,emc2305";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x4c>;
> + fan at 0 {
> + reg = <0>;
> + };
> + fan at 1 {
> + reg = <1>;
> + };
> + fan at 2 {
> + reg = <2>;
> + };
> + fan at 3 {
> + reg = <3>;
> + };
> + fan at 4 {
> + reg = <4>;
> + };
> + };
> + at24c512 at 54 {
> + compatible = "atmel,24c512";
> + reg = <0x54>;
> + u-boot,i2c-offset-len = <2>;
> + };
> + ds1339 at 68 {
> + compatible = "dallas,ds1339";
> + reg = <0x68>;
> + };
> + };
> +
> + serial at 12000 {
> + status = "okay";
> + };
> +
> + serial at 12100 {
> + status = "okay";
> + };
> +
> + ethernet at 34000 {
> + status = "okay";
> + phy = <&phy1>;
> + phy-mode = "sgmii";
> + };
> +
> + usb at 58000 {
> + status = "ok";
> + };
> +
> + ethernet at 70000 {
> + status = "okay";
> + phy = <&phy0>;
> + phy-mode = "sgmii";
> + };
> +
> + mdio at 72004 {
> + phy0: ethernet-phy at 0 {
> + reg = <1>;
> + };
> +
> + phy1: ethernet-phy at 1 {
> + reg = <0>;
> + };
> + };
> +
> + sata at a8000 {
> + status = "okay";
> + };
> +
> + sdhci at d8000 {
> + broken-cd;
> + wp-inverted;
> + bus-width = <4>;
> + status = "okay";
> + no-1-8-v;
> + };
> +
> + usb3 at f0000 {
> + status = "okay";
> + };
> + };
> +
> + pcie-controller {
> + status = "okay";
> + /*
> + * The two PCIe units are accessible through
> + * standard PCIe slots on the board.
> + */
> + pcie at 3,0 {
> + /* Port 0, Lane 0 */
> + status = "okay";
> + };
> + };
> +
> + MDIO0: mdio0 {
> + compatible = "virtual,mdio-gpio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + gpios = < /*MDC*/ &gpio0 13 0
> + /*MDIO*/ &gpio0 14 0>;
> + mv88e1240 at 0 {
> + reg = <0x0>;
> + };
> + mv88e1240 at 1 {
> + reg = <0x1>;
> + };
> + mv88e1240 at 2 {
> + reg = <0x2>;
> + };
> + mv88e1240 at 3 {
> + reg = <0x3>;
> + };
> + mv88e1240 at 4 {
> + reg = <0x4>;
> + };
> + mv88e1240 at 5 {
> + reg = <0x5>;
> + };
> + mv88e1240 at 6 {
> + reg = <0x6>;
> + };
> + mv88e1240 at 7 {
> + reg = <0x7>;
> + };
> + mv88e1240 at 8 {
> + reg = <0x8>;
> + };
> + mv88e1240 at 9 {
> + reg = <0x9>;
> + };
> + mv88e1240 at a {
> + reg = <0xa>;
> + };
> + mv88e1240 at b {
> + reg = <0xb>;
> + };
> + mv88e1240 at c {
> + reg = <0xc>;
> + };
> + mv88e1240 at d {
> + reg = <0xd>;
> + };
> + mv88e1240 at e {
> + reg = <0xe>;
> + };
> + mv88e1240 at f {
> + reg = <0xf>;
> + };
> + mv88e1240 at 10 {
> + reg = <0x10>;
> + };
> + mv88e1240 at 11 {
> + reg = <0x11>;
> + };
> + mv88e1240 at 12 {
> + reg = <0x12>;
> + };
> + mv88e1240 at 13 {
> + reg = <0x13>;
> + };
> + mv88e1240 at 14 {
> + reg = <0x14>;
> + };
> + mv88e1240 at 15 {
> + reg = <0x15>;
> + };
> + mv88e1240 at 16 {
> + reg = <0x16>;
> + };
> + mv88e1240 at 17 {
> + reg = <0x17>;
> + };
> + mv88e1240 at 18 {
> + reg = <0x18>;
> + };
> + mv88e1240 at 19 {
> + reg = <0x19>;
> + };
> + mv88e1240 at 1a {
> + reg = <0x1a>;
> + };
> + mv88e1240 at 1b {
> + reg = <0x1b>;
> + };
> + mv88e1240 at 1c {
> + reg = <0x1c>;
> + };
> + mv88e1240 at 1d {
> + reg = <0x1d>;
> + };
> + mv88e1240 at 1e {
> + reg = <0x1e>;
> + };
> + mv88e1240 at 1f {
> + reg = <0x1f>;
> + };
> + };
> +
> + MDIO1: mdio1 {
> + compatible = "virtual,mdio-gpio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + gpios = < /*MDC*/ &gpio0 25 0
> + /*MDIO*/ &gpio1 13 0>;
> + mv88e1240 at 0 {
> + reg = <0x0>;
> + };
> + mv88e1240 at 1 {
> + reg = <0x1>;
> + };
> + mv88e1240 at 2 {
> + reg = <0x2>;
> + };
> + mv88e1240 at 3 {
> + reg = <0x3>;
> + };
> + mv88e1240 at 4 {
> + reg = <0x4>;
> + };
> + mv88e1240 at 5 {
> + reg = <0x5>;
> + };
> + mv88e1240 at 6 {
> + reg = <0x6>;
> + };
> + mv88e1240 at 7 {
> + reg = <0x7>;
> + };
> + mv88e1240 at 8 {
> + reg = <0x8>;
> + };
> + mv88e1240 at 9 {
> + reg = <0x9>;
> + };
> + mv88e1240 at a {
> + reg = <0xa>;
> + };
> + mv88e1240 at b {
> + reg = <0xb>;
> + };
> + mv88e1240 at c {
> + reg = <0xc>;
> + };
> + mv88e1240 at d {
> + reg = <0xd>;
> + };
> + mv88e1240 at e {
> + reg = <0xe>;
> + };
> + mv88e1240 at f {
> + reg = <0xf>;
> + };
> + mv88e1240 at 10 {
> + reg = <0x10>;
> + };
> + mv88e1240 at 11 {
> + reg = <0x11>;
> + };
> + mv88e1240 at 12 {
> + reg = <0x12>;
> + };
> + mv88e1240 at 13 {
> + reg = <0x13>;
> + };
> + mv88e1240 at 14 {
> + reg = <0x14>;
> + };
> + mv88e1240 at 15 {
> + reg = <0x15>;
> + };
> + mv88e1240 at 16 {
> + reg = <0x16>;
> + };
> + mv88e1240 at 17 {
> + reg = <0x17>;
> + };
> + mv88e1240 at 18 {
> + reg = <0x18>;
> + };
> + mv88e1240 at 19 {
> + reg = <0x19>;
> + };
> + mv88e1240 at 1a {
> + reg = <0x1a>;
> + };
> + mv88e1240 at 1b {
> + reg = <0x1b>;
> + };
> + mv88e1240 at 1c {
> + reg = <0x1c>;
> + };
> + mv88e1240 at 1d {
> + reg = <0x1d>;
> + };
> + mv88e1240 at 1e {
> + reg = <0x1e>;
> + };
> + mv88e1240 at 1f {
> + reg = <0x1f>;
> + };
> + };
> +
> + MDIO2: mdio2 {
> + compatible = "virtual,mdio-gpio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + gpios = < /*MDC*/ &gpio1 14 0
> + /*MDIO*/ &gpio0 24 0>;
> + mv88e1240 at 0 {
> + reg = <0x0>;
> + };
> + mv88e1240 at 1 {
> + reg = <0x1>;
> + };
> + mv88e1240 at 2 {
> + reg = <0x2>;
> + };
> + mv88e1240 at 3 {
> + reg = <0x3>;
> + };
> + mv88e1240 at 4 {
> + reg = <0x4>;
> + };
> + mv88e1240 at 5 {
> + reg = <0x5>;
> + };
> + mv88e1240 at 6 {
> + reg = <0x6>;
> + };
> + mv88e1240 at 7 {
> + reg = <0x7>;
> + };
> + mv88e1240 at 8 {
> + reg = <0x8>;
> + };
> + mv88e1240 at 9 {
> + reg = <0x9>;
> + };
> + mv88e1240 at a {
> + reg = <0xa>;
> + };
> + mv88e1240 at b {
> + reg = <0xb>;
> + };
> + mv88e1240 at c {
> + reg = <0xc>;
> + };
> + mv88e1240 at d {
> + reg = <0xd>;
> + };
> + mv88e1240 at e {
> + reg = <0xe>;
> + };
> + mv88e1240 at f {
> + reg = <0xf>;
> + };
> + mv88e1240 at 10 {
> + reg = <0x10>;
> + };
> + mv88e1240 at 11 {
> + reg = <0x11>;
> + };
> + mv88e1240 at 12 {
> + reg = <0x12>;
> + };
> + mv88e1240 at 13 {
> + reg = <0x13>;
> + };
> + mv88e1240 at 14 {
> + reg = <0x14>;
> + };
> + mv88e1240 at 15 {
> + reg = <0x15>;
> + };
> + };
> + };
> +
> + cat_gpio_0 {
> + compatible = "generic,cat-gpio-0";
> + gpios = <&PCA23 0x20 0x0>;
> + };
> +
> + cat_gpio_1 {
> + compatible = "generic,cat-gpio-1";
> + gpios = <&PCA21 0x20 0x0>;
> + };
> +
> + cat_gpio_2 {
> + compatible = "generic,cat-gpio-2";
> + gpios = <&PCA24 0x20 0x0>;
> + };
> +
> + cat_gpio_3 {
> + compatible = "generic,cat-gpio-3";
> + gpios = <&PCA25 0x20 0x0>;
> + };
> +
> + cat_gpio_4 {
> + compatible = "generic,cat-gpio-4";
> + gpios = <&PCA26 0x20 0x0>;
> + };
> +
> + second_octo_gpio_0 {
> + compatible = "generic,second-octo-gpio-0";
> + gpios = <&PCA23 0x27 0x0>;
> + };
> +
> + fpga_program_gpio {
> + compatible = "generic,fpga-program-gpio";
> + u-boot,dm-pre-reloc;
> + gpios = <&PCA22 31 0>;
> + };
> +
> + fpga_done_gpio {
> + compatible = "generic,fpga-done-gpio";
> + u-boot,dm-pre-reloc;
> + gpios = <&PCA22 19 0>;
> + };
> +
> + fpga_ready_gpio {
> + compatible = "generic,fpga-ready-gpio";
> + u-boot,dm-pre-reloc;
> + gpios = <&PCA22 27 0>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + finder_led {
> + label = "finder-led";
> + gpios = <&PCA22 25 0>;
> + };
> +
> + status_led {
> + label = "status-led";
> + gpios = <&gpio0 29 0>;
> + };
> + };
> +};
> diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
> index 1ca7b52..ac36894 100644
> --- a/arch/arm/mach-mvebu/Kconfig
> +++ b/arch/arm/mach-mvebu/Kconfig
> @@ -102,6 +102,10 @@ config TARGET_THEADORABLE
> bool "Support theadorable Armada XP"
> select MV78260
>
> +config TARGET_CONTROLCENTERDC
> + bool "Support CONTROLCENTERDC"
> + select 88F6820
> +
> endchoice
>
> config SYS_BOARD
> diff --git a/board/gdsys/38x/.gitignore b/board/gdsys/38x/.gitignore
> new file mode 100644
> index 0000000..775b934
> --- /dev/null
> +++ b/board/gdsys/38x/.gitignore
> @@ -0,0 +1 @@
> +kwbimage.cfg
> diff --git a/board/gdsys/38x/Kconfig b/board/gdsys/38x/Kconfig
> new file mode 100644
> index 0000000..dd99ac5
> --- /dev/null
> +++ b/board/gdsys/38x/Kconfig
> @@ -0,0 +1,42 @@
> +if TARGET_CONTROLCENTERDC
> +
> +config SYS_BOARD
> + default "38x"
> +
> +config SYS_VENDOR
> + default "gdsys"
> +
> +config SYS_SOC
> + default "mvebu"
> +
> +config SYS_CONFIG_NAME
> + default "controlcenterdc"
> +
> +menu "Controlcenter DC board options"
> +
> +choice
> + prompt "Select boot method"
> +
> +config SPL_BOOT_DEVICE_SPI
> + bool "SPI"
> +
> +config SPL_BOOT_DEVICE_MMC
> + bool "MMC"
> + select SPL_LIBDISK_SUPPORT
> +
> +endchoice
> +
> +#config SPL_BOOT_DEVICE
> +# int
> +# default 1 if SPL_BOOT_DEVICE_SPI
> +# default 2 if SPL_BOOT_DEVICE_MMC
> +
> +config SYS_BOOTIMAGE_DEST_ADDR
> + hex "Boot image destination address"
> + default 0x007fffc0
> + help
> + Blah
Hmmm, the help text is not really "helpful". ;)
This option is also not referenced, so perhaps you can remove it?
> +
> +endmenu
> +
> +endif
> diff --git a/board/gdsys/38x/MAINTAINERS b/board/gdsys/38x/MAINTAINERS
> new file mode 100644
> index 0000000..5dbc6ec
> --- /dev/null
> +++ b/board/gdsys/38x/MAINTAINERS
> @@ -0,0 +1,7 @@
> +38X BOARD
> +M: Dirk Eibach <eibach at gdsys.cc>
> +M: Mario Six <six at gdsys.de>
> +S: Maintained
> +F: board/gdsys/38x/
> +F: include/configs/controlcenterdc.h
> +F: configs/controlcenterdc_defconfig
> diff --git a/board/gdsys/38x/Makefile b/board/gdsys/38x/Makefile
> new file mode 100644
> index 0000000..6d17196
> --- /dev/null
> +++ b/board/gdsys/38x/Makefile
> @@ -0,0 +1,30 @@
> +#
> +# Copyright (C) 2015 Stefan Roese <sr at denx.de>
> +# Copyright (C) 2015 Reinhard Pfau <reinhard.pfau at gdsys.cc>
> +# Copyright (C) 2016 Mario Six <mario.six at gdsys.cc>
> +#
> +# SPDX-License-Identifier: GPL-2.0+
> +#
> +
> +obj-$(CONFIG_TARGET_CONTROLCENTERDC) += controlcenterdc.o hre.o spl.o keyprogram.o dt_helpers.o
> +
> +ifeq ($(CONFIG_SPL_BUILD),)
> +
> +extra-$(CONFIG_TARGET_CONTROLCENTERDC) += kwbimage.cfg
> +
> +ifneq ($(CONFIG_TARGET_CONTROLCENTERDC),)
> +KWB_REPLACE += BOOT_FROM
> +ifneq ($(CONFIG_SPL_BOOT_DEVICE_SPI),)
> + KWB_CFG_BOOT_FROM=spi
> +endif
> +ifneq ($(CONFIG_SPL_BOOT_DEVICE_MMC),)
> + KWB_CFG_BOOT_FROM=sdio
> +endif
> +endif
Do you have multiple build targets for this directory? Do you need
to have this check with CONFIG_TARGET_CONTROLCENTERDC?
> +
> +$(src)/kwbimage.cfg: $(src)/kwbimage.cfg.in include/autoconf.mk \
> + include/config/auto.conf
> + $(Q)sed -ne '$(foreach V,$(KWB_REPLACE),s/^#@$(V)/$(V) $(KWB_CFG_$(V))/;)p' \
> + <$< >$@
> +
> +endif
> diff --git a/board/gdsys/38x/README b/board/gdsys/38x/README
> new file mode 100644
> index 0000000..9bea5b3
> --- /dev/null
> +++ b/board/gdsys/38x/README
> @@ -0,0 +1,18 @@
> +Update from original Marvell U-Boot to mainline U-Boot:
> +-------------------------------------------------------
> +
> +The resulting image including the SPL binary with the
> +full DDR setup is "u-boot-spl.kwb".
> +
> +To update the SPI NOR flash, please use the following
> +command:
> +
> +=> sf probe;tftpboot 2000000 db-88f6820-gp/u-boot-spl.kwb;\
> +sf update 2000000 0 60000
> +
> +Note that the original Marvell U-Boot seems to have
> +problems with the "sf update" command. This does not
> +work reliable. So here this command should be used:
> +
> +=> sf probe;tftpboot 2000000 db-88f6820-gp/u-boot-spl.kwb;\
> +sf erase 0 60000;sf write 2000000 0 60000
You copied this file from the Marvell directory. Does it really
make sense to add it here as well? I suggest to just remove it.
> diff --git a/board/gdsys/38x/controlcenterdc.c b/board/gdsys/38x/controlcenterdc.c
> new file mode 100644
> index 0000000..f151265
> --- /dev/null
> +++ b/board/gdsys/38x/controlcenterdc.c
> @@ -0,0 +1,717 @@
> +/*
> + * Copyright (C) 2015 Stefan Roese <sr at denx.de>
> + * Copyright (C) 2016 Mario Six <mario.six at gdsys.cc>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <console.h> /* disable_ctrlc */
> +#include <miiphy.h>
> +#include <tpm.h>
> +#include <asm/io.h>
> +#include <asm/arch/cpu.h>
> +#include <asm/arch/gpio.h>
> +#include <asm-generic/gpio.h>
> +
> +#include "../drivers/ddr/marvell/a38x/ddr3_a38x_topology.h"
> +#include "../arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.h"
> +
> +#include "keyprogram.h"
> +#include "dt_helpers.h"
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +#define ETH_PHY_CTRL_REG 0
> +#define ETH_PHY_CTRL_POWER_DOWN_BIT 11
> +#define ETH_PHY_CTRL_POWER_DOWN_MASK (1 << ETH_PHY_CTRL_POWER_DOWN_BIT)
> +
> +#define DB_GP_88F68XX_GPP_OUT_ENA_LOW 0x7fffffff
> +#define DB_GP_88F68XX_GPP_OUT_ENA_MID 0xffffefff
> +
> +#define DB_GP_88F68XX_GPP_OUT_VAL_LOW 0x0
> +#define DB_GP_88F68XX_GPP_OUT_VAL_MID 0x00001000
> +#define DB_GP_88F68XX_GPP_POL_LOW 0x0
> +#define DB_GP_88F68XX_GPP_POL_MID 0x0
> +
> +#ifndef CONFIG_SPL_BUILD
> +enum {
> + HWVER_100 = 0,
> + HWVER_110 = 1,
> + HWVER_120 = 2,
> +};
> +
> +enum {
> + PORTTYPE_MAIN_CAT,
> + PORTTYPE_TOP_CAT,
> + PORTTYPE_16C_16F,
> + PORTTYPE_UNKNOWN
> +};
> +
> +static struct porttype {
> + bool phy_invert_in_pol;
> + bool phy_invert_out_pol;
> +} porttypes[] = {
> + { true, false },
> + { false, true },
> + { false, false },
> +};
> +
> +struct ihs_fpga {
> + u32 reflection_low; /* 0x0000 */
> + u32 versions; /* 0x0004 */
> + u32 fpga_version; /* 0x0008 */
> + u32 fpga_features; /* 0x000c */
> + u32 reserved0[4]; /* 0x0010 */
> + u32 control; /* 0x0020 */
> + u32 reserved1[375]; /* 0x0024 */
> + u32 qsgmii_port_state[80]; /* 0x0600 */
> +};
> +
> +static struct ihs_fpga *fpga;
> +
> +static struct pci_device_id hydra_supported[] = {
> + { 0x6d5e, 0xcdc1 },
> + {}
> +};
> +#endif
> +
> +/*
> + * Define the DDR layout / topology here in the board file. This will
> + * be used by the DDR3 init code in the SPL U-Boot version to configure
> + * the DDR3 controller.
> + */
> +static struct hws_topology_map ddr_topology_map = {
> + 0x1, /* active interfaces */
> + /* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
> + { { { {0x1, 0, 0, 0},
> + {0x1, 0, 0, 0},
> + {0x1, 0, 0, 0},
> + {0x1, 0, 0, 0},
> + {0x1, 0, 0, 0} },
> + SPEED_BIN_DDR_1600K, /* speed_bin */
> + BUS_WIDTH_16, /* memory_width */
> + MEM_4G, /* mem_size */
> + DDR_FREQ_533, /* frequency */
> + 0, 0, /* cas_l cas_wl */
> + HWS_TEMP_LOW} }, /* temperature */
> + 5, /* Num Of Bus Per Interface*/
> + BUS_MASK_32BIT /* Busses mask */
> +};
> +
> +static struct serdes_map serdes_topology_map[] = {
> + {SGMII0, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
> + {USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
> + /* SATA tx polarity is inverted */
> + {SATA1, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 1},
> + {SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
> + {DEFAULT_SERDES, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
> + {PEX2, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0}
> +};
> +
> +int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
> +{
> + *serdes_map_array = serdes_topology_map;
> + *count = ARRAY_SIZE(serdes_topology_map);
> + return 0;
> +}
> +
> +void board_pex_config(void)
> +{
> +#ifdef CONFIG_SPL_BUILD
> + uint k;
> + struct gpio_desc gpio = {};
> +
> + if (get_gpio("generic,fpga-program-gpio", &gpio)) {
> + /* prepare FPGA reconfiguration */
> + dm_gpio_set_dir_flags(&gpio, GPIOD_IS_OUT);
> + dm_gpio_set_value(&gpio, 0);
> +
> + /* give lunatic PCIe clock some time to stabilize */
> + mdelay(500);
> +
> + /* start FPGA reconfiguration */
> + dm_gpio_set_dir_flags(&gpio, GPIOD_IS_IN);
> + }
> +
> + /* wait for FPGA done */
> + if (get_gpio("generic,fpga-done-gpio", &gpio)) {
> + for (k = 0; k < 20; ++k) {
> + if (dm_gpio_get_value(&gpio)) {
> + printf("FPGA done after %u rounds\n", k);
> + break;
> + }
> + mdelay(100);
> + }
> + }
> +
> + /* disable FPGA reset */
> + kw_gpio_set_valid(6, GPIO_OUTPUT_OK);
> + kw_gpio_direction_output(6, 1);
Ah, here you use the "old" GPIO infrastucture. Please move to the DM
GPIO driver and use the generic API instead.
> +
> + /* wait for FPGA ready */
> + if (get_gpio("generic,fpga-ready-gpio", &gpio)) {
> + for (k = 0; k < 2; ++k) {
> + if (!dm_gpio_get_value(&gpio))
> + break;
> + mdelay(100);
> + }
> + }
> +#endif
> +}
> +
> +struct hws_topology_map *ddr3_get_topology_map(void)
> +{
> + return &ddr_topology_map;
> +}
> +
> +int board_early_init_f(void)
> +{
> +#ifdef CONFIG_SPL_BUILD
> + /* Configure MPP */
> + writel(0x00111111, MVEBU_MPP_BASE + 0x00);
> + writel(0x40040000, MVEBU_MPP_BASE + 0x04);
> + writel(0x00466444, MVEBU_MPP_BASE + 0x08);
> + writel(0x00043300, MVEBU_MPP_BASE + 0x0c);
> + writel(0x44400000, MVEBU_MPP_BASE + 0x10);
> + writel(0x20000334, MVEBU_MPP_BASE + 0x14);
> + writel(0x40000000, MVEBU_MPP_BASE + 0x18);
> + writel(0x00004444, MVEBU_MPP_BASE + 0x1c);
> +
> + /* Set GPP Out value */
> + writel(DB_GP_88F68XX_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
> + writel(DB_GP_88F68XX_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
> +
> + /* Set GPP Polarity */
> + writel(DB_GP_88F68XX_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
> + writel(DB_GP_88F68XX_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c);
> +
> + /* Set GPP Out Enable */
> + writel(DB_GP_88F68XX_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
> + writel(DB_GP_88F68XX_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
> +#endif
> +
> + return 0;
> +}
> +
> +int board_init(void)
> +{
> + /* adress of boot parameters */
> + gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
> +
> + return 0;
> +}
> +
> +int checkboard(void)
> +{
> + puts("Board: Controlcenter Digital Compact\n");
> +
> + return 0;
> +}
With DT support you should already get the board model printed from
the DT. Do yo need this line here as well?
> +
> +#ifndef CONFIG_SPL_BUILD
> +static void ihs_phy_config(struct phy_device *phydev, bool qinpn, bool qoutpn)
> +{
> + u16 reg;
> +
> + phy_config(phydev);
> +
> + /* enable QSGMII autonegotiation with flow control */
> + phy_write(phydev, MDIO_DEVAD_NONE, 22, 0x0004);
> + reg = phy_read(phydev, MDIO_DEVAD_NONE, 16);
> + reg |= (3 << 6);
> + phy_write(phydev, MDIO_DEVAD_NONE, 16, reg);
> +
> + /*
> + * invert QSGMII Q_INP/N and Q_OUTP/N if required
> + * and perform global reset
> + */
> + reg = phy_read(phydev, MDIO_DEVAD_NONE, 26);
> + if (qinpn)
> + reg |= (1 << 13);
> + if (qoutpn)
> + reg |= (1 << 12);
> + reg |= (1 << 15);
> + phy_write(phydev, MDIO_DEVAD_NONE, 26, reg);
> +
> + /* advertise 1000BASE-T full-duplex only */
> + phy_write(phydev, MDIO_DEVAD_NONE, 22, 0x0000);
> + reg = phy_read(phydev, MDIO_DEVAD_NONE, 4);
> + reg &= ~0x1e0;
> + phy_write(phydev, MDIO_DEVAD_NONE, 4, reg);
> + reg = phy_read(phydev, MDIO_DEVAD_NONE, 9);
> + reg = (reg & ~0x300) | 0x200;
> + phy_write(phydev, MDIO_DEVAD_NONE, 9, reg);
> +
> + /* copper power up */
> + reg = phy_read(phydev, MDIO_DEVAD_NONE, 16);
> + reg &= ~0x0004;
> + phy_write(phydev, MDIO_DEVAD_NONE, 16, reg);
> +}
> +
> +void init_host_phys(struct mii_dev *bus)
> +{
> + uint k;
> +
> + for (k = 0; k < 2; ++k) {
> + struct phy_device *phydev;
> +
> + phydev = phy_find_by_mask(bus, 1 << k,
> + PHY_INTERFACE_MODE_SGMII);
> +
> + if (phydev)
> + phy_config(phydev);
> + }
> +}
> +
> +uint calculate_octo_phy_mask(void)
> +{
> + uint k;
> + uint octo_phy_mask = 0;
> + struct gpio_desc gpio = {};
> + char name[64];
> +
> + /* mark all octo phys that should be present */
> + for (k = 0; k < 5; ++k) {
> + snprintf(name, 64, "generic,cat-gpio-%u", k);
> +
> + if (!get_gpio(name, &gpio))
> + continue;
> +
> + /* check CAT flag */
> + if (dm_gpio_get_value(&gpio))
> + octo_phy_mask |= (1 << (k * 2));
> + else
> + /* If CAT == 0, there's no second octo phy -> skip */
> + continue;
> +
> + snprintf(name, 64, "generic,second-octo-gpio-%u", k);
> +
> + if (!get_gpio(name, &gpio)) {
> + /* default: second octo phy is present */
> + octo_phy_mask |= (1 << (k * 2 + 1));
> + continue;
> + }
> +
> + if (dm_gpio_get_value(&gpio) == 0)
> + octo_phy_mask |= (1 << (k * 2 + 1));
> + }
> +
> + return octo_phy_mask;
> +}
> +
> +int register_miiphy_bus(uint k, struct mii_dev **bus)
> +{
> + int retval;
> + struct mii_dev *mdiodev = mdio_alloc();
> + char *name = bb_miiphy_buses[k].name;
I'm wondering how this works if "bb_miiphy_buses" is defined later in
this file and you have no header file.
> +
> + if (!mdiodev)
> + return -ENOMEM;
> + strncpy(mdiodev->name,
> + name,
> + MDIO_NAME_LEN);
> + mdiodev->read = bb_miiphy_read;
> + mdiodev->write = bb_miiphy_write;
> +
> + retval = mdio_register(mdiodev);
> + if (retval < 0)
> + return retval;
> + *bus = miiphy_get_dev_by_name(name);
> +
> + return 0;
> +}
> +
> +struct porttype *get_porttype(uint octo_phy_mask, uint k)
> +{
> + uint octo_index = k * 4;
> +
> + if (!k) {
> + if (octo_phy_mask & 0x01)
> + return &porttypes[PORTTYPE_MAIN_CAT];
> + else if (!(octo_phy_mask & 0x03))
> + return &porttypes[PORTTYPE_16C_16F];
> + } else {
> + if (octo_phy_mask & (1 << octo_index))
> + return &porttypes[PORTTYPE_TOP_CAT];
> + }
> +
> + return NULL;
> +}
> +
> +int init_octo_phys(uint octo_phy_mask)
> +{
> + uint bus_idx;
> +
> + /* there are up to four octo-phys on each mdio bus */
> + for (bus_idx = 0; bus_idx < bb_miiphy_buses_num; ++bus_idx) {
> + uint m;
> + uint octo_index = bus_idx * 4;
> + struct mii_dev *bus = NULL;
> + struct porttype *porttype = NULL;
> + int ret;
> +
> + porttype = get_porttype(octo_phy_mask, bus_idx);
> +
> + if (!porttype)
> + continue;
> +
> + for (m = 0; m < 4; ++m) {
> + uint phy_idx;
> +
> + /* Register a bus device if there is at least one phy
> + * on the current bus
> + */
Multiline comment style please.
> + if (!m && octo_phy_mask & (0xf << octo_index)) {
> + ret = register_miiphy_bus(bus_idx, &bus);
> + if (ret)
> + return ret;
> + }
> +
> + if (!(octo_phy_mask & (1 << (octo_index + m))))
> + continue;
> +
> + for (phy_idx = 0; phy_idx < 8; ++phy_idx) {
> + struct phy_device *phydev = phy_find_by_mask(
> + bus, 1 << (m * 8 + phy_idx),
> + PHY_INTERFACE_MODE_MII);
> +
> + printf(" %u", bus_idx * 32 + m * 8 + phy_idx);
> +
> + ihs_phy_config(phydev,
> + porttype->phy_invert_in_pol,
> + porttype->phy_invert_out_pol);
> + }
> + }
> + }
> +
> + return 0;
> +}
> +
> +int ccdc_eth_init(void)
> +{
> + uint k;
> + uint octo_phy_mask = 0;
> + int ret;
> + struct mii_dev *bus;
> +
> + /* Init SoC's phys */
> + bus = miiphy_get_dev_by_name("ethernet at 34000");
> +
> + if (bus)
> + init_host_phys(bus);
> +
> + bus = miiphy_get_dev_by_name("ethernet at 70000");
> +
> + if (bus)
> + init_host_phys(bus);
> +
> + /* Init octo phys */
> + octo_phy_mask = calculate_octo_phy_mask();
> +
> + printf("IHS PHYS: %08x", octo_phy_mask);
> +
> + ret = init_octo_phys(octo_phy_mask);
> +
> + if (ret)
> + return ret;
> +
> + printf("\n");
> +
> + /* reset all FPGA-QSGMII instances */
> + for (k = 0; k < 80; ++k)
> + writel(1 << 31, &fpga->qsgmii_port_state[k]);
> +
> + udelay(100);
> +
> + for (k = 0; k < 80; ++k)
> + writel(0, &fpga->qsgmii_port_state[k]);
> + return 0;
> +}
> +
> +void print_hydra_version(uint index)
> +{
> + u32 versions = readl(&fpga->versions);
> + u32 fpga_version = readl(&fpga->fpga_version);
> +
> + uint hardware_version = versions & 0xf;
> +
> + printf("FPGA%u: mapped to %p\n ", index, fpga);
> +
> + switch (hardware_version) {
> + case HWVER_100:
> + printf("HW-Ver 1.00\n");
> + break;
> +
> + case HWVER_110:
> + printf("HW-Ver 1.10\n");
> + break;
> +
> + case HWVER_120:
> + printf("HW-Ver 1.20\n");
> + break;
> +
> + default:
> + printf("HW-Ver %d(not supported)\n",
> + hardware_version);
> + break;
> + }
> +
> + printf(" FPGA V %d.%02d\n",
> + fpga_version / 100, fpga_version % 100);
> +}
> +
> +static void hydra_initialize(void)
> +{
> + uint i;
> + pci_dev_t devno;
> +
> + /* Find and probe all the matching PCI devices */
> + for (i = 0; (devno = pci_find_devices(hydra_supported, i)) >= 0; i++) {
> + u32 val;
> +
> + /* Try to enable I/O accesses and bus-mastering */
> + val = PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER;
> + pci_write_config_dword(devno, PCI_COMMAND, val);
> +
> + /* Make sure it worked */
> + pci_read_config_dword(devno, PCI_COMMAND, &val);
> + if (!(val & PCI_COMMAND_MEMORY)) {
> + puts("Can't enable I/O memory\n");
> + continue;
> + }
> + if (!(val & PCI_COMMAND_MASTER)) {
> + puts("Can't enable bus-mastering\n");
> + continue;
> + }
> +
> + /* read FPGA details */
> + fpga = pci_map_bar(devno, PCI_BASE_ADDRESS_0,
> + PCI_REGION_MEM);
> +
> + print_hydra_version(i);
> + }
> +}
> +#endif
> +
> +int board_late_init(void)
> +{
> +#ifndef CONFIG_SPL_BUILD
> + hydra_initialize();
> +#endif
> + return 0;
> +}
> +
> +int board_fix_fdt(void)
> +{
> + struct udevice *bus;
> + uint k;
> + char name[64];
> +
> + bus = dev_get_by_ofname("/soc/internal-regs/i2c at 11000");
> +
> + for (k = 0x21; k <= 0x26; k++) {
> + snprintf(name, 64,
> + "/soc/internal-regs/i2c at 11000/pca9698@%02x", k);
> +
> + if (!dm_i2c_simple_probe(bus, k))
> + fdt_disable_by_ofname(name);
> + }
> +
> + return 0;
> +}
> +
> +int last_stage_init(void)
> +{
> + disable_ctrlc(1);
> +
> +#ifndef CONFIG_SPL_BUILD
> + ccdc_eth_init();
> +#endif
> + if (tpm_init() || tpm_startup(TPM_ST_CLEAR) ||
> + tpm_continue_self_test()) {
> + return 1;
> + }
> +
> + mdelay(37);
> +
> + flush_keys();
> + load_and_run_keyprog();
> +
> + return 0;
> +}
> +
> +#ifndef CONFIG_SPL_BUILD
> +
> +#define REFL_PATTERN (0xdededede)
> +#define REFL_PATTERN_INV (~REFL_PATTERN)
> +
> +int do_hydrate(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
> +{
> + uint k = 0;
> + void __iomem *pcie2_base = (void __iomem *)(MVEBU_REG_PCIE_BASE +
> + 0x4000);
> +
> + if (!fpga)
> + return -1;
> +
> + while (1) {
> + u32 res;
> +
> + writel(REFL_PATTERN, &fpga->reflection_low);
> + res = readl(&fpga->reflection_low);
> + if (res != REFL_PATTERN_INV)
> + printf("round %u: read %08x, expected %08x\n",
> + k, res, REFL_PATTERN_INV);
> + writel(REFL_PATTERN_INV, &fpga->reflection_low);
> + res = readl(&fpga->reflection_low);
> + if (res != REFL_PATTERN)
> + printf("round %u: read %08x, expected %08x\n",
> + k, res, REFL_PATTERN);
> +
> + res = readl(pcie2_base + 0x118) & 0x1f;
> + if (res)
> + printf("FrstErrPtr %u\n", res);
> + res = readl(pcie2_base + 0x104);
> + if (res) {
> + printf("Uncorrectable Error Status 0x%08x\n", res);
> + writel(res, pcie2_base + 0x104);
> + }
> +
> + if (!(++k % 10000))
> + printf("round %u\n", k);
> +
> + if (ctrlc())
> + break;
> + }
> +
> + return 0;
> +}
> +
> +U_BOOT_CMD(
> + hydrate, 1, 0, do_hydrate,
> + "hydra reflection test",
> + "hydra reflection test"
> +);
> +
> +/*
> + * MII GPIO bitbang implementation
> + * MDC MDIO bus
> + * 13 14 PHY1-4
> + * 25 45 PHY5-8
> + * 46 24 PHY9-10
> + */
> +
> +struct gpio_mii {
> + int mdc;
> + int mdio;
> + int mdio_value;
> +} gpio_mii_set[] = {
> + { 13, 14, 1 },
> + { 25, 45, 1 },
> + { 46, 24, 1 },
> +};
> +
> +static int mii_mdio_init(struct bb_miiphy_bus *bus)
> +{
> + struct gpio_mii *gpio_mii = bus->priv;
> +
> + kw_gpio_set_valid(gpio_mii->mdc, GPIO_OUTPUT_OK);
> + kw_gpio_set_valid(gpio_mii->mdio, GPIO_INPUT_OK | GPIO_OUTPUT_OK);
> + kw_gpio_direction_output(gpio_mii->mdc, 1);
> +
> + return 0;
> +}
> +
> +static int mii_mdio_active(struct bb_miiphy_bus *bus)
> +{
> + struct gpio_mii *gpio_mii = bus->priv;
> +
> + kw_gpio_direction_output(gpio_mii->mdio, gpio_mii->mdio_value);
> +
> + return 0;
> +}
> +
> +static int mii_mdio_tristate(struct bb_miiphy_bus *bus)
> +{
> + struct gpio_mii *gpio_mii = bus->priv;
> +
> + kw_gpio_direction_input(gpio_mii->mdio);
> +
> + return 0;
> +}
> +
> +static int mii_set_mdio(struct bb_miiphy_bus *bus, int v)
> +{
> + struct gpio_mii *gpio_mii = bus->priv;
> +
> + kw_gpio_set_value(gpio_mii->mdio, v);
> + gpio_mii->mdio_value = v;
> +
> + return 0;
> +}
> +
> +static int mii_get_mdio(struct bb_miiphy_bus *bus, int *v)
> +{
> + struct gpio_mii *gpio_mii = bus->priv;
> +
> + *v = (kw_gpio_get_value(gpio_mii->mdio) != 0);
> +
> + return 0;
> +}
> +
> +static int mii_set_mdc(struct bb_miiphy_bus *bus, int v)
> +{
> + struct gpio_mii *gpio_mii = bus->priv;
> +
> + kw_gpio_set_value(gpio_mii->mdc, v);
> +
> + return 0;
> +}
> +
> +static int mii_delay(struct bb_miiphy_bus *bus)
> +{
> + udelay(1);
> +
> + return 0;
> +}
> +
> +struct bb_miiphy_bus bb_miiphy_buses[] = {
> + {
> + .name = "ihs0",
> + .init = mii_mdio_init,
> + .mdio_active = mii_mdio_active,
> + .mdio_tristate = mii_mdio_tristate,
> + .set_mdio = mii_set_mdio,
> + .get_mdio = mii_get_mdio,
> + .set_mdc = mii_set_mdc,
> + .delay = mii_delay,
> + .priv = &gpio_mii_set[0],
> + },
> + {
> + .name = "ihs1",
> + .init = mii_mdio_init,
> + .mdio_active = mii_mdio_active,
> + .mdio_tristate = mii_mdio_tristate,
> + .set_mdio = mii_set_mdio,
> + .get_mdio = mii_get_mdio,
> + .set_mdc = mii_set_mdc,
> + .delay = mii_delay,
> + .priv = &gpio_mii_set[1],
> + },
> + {
> + .name = "ihs2",
> + .init = mii_mdio_init,
> + .mdio_active = mii_mdio_active,
> + .mdio_tristate = mii_mdio_tristate,
> + .set_mdio = mii_set_mdio,
> + .get_mdio = mii_get_mdio,
> + .set_mdc = mii_set_mdc,
> + .delay = mii_delay,
> + .priv = &gpio_mii_set[2],
> + },
> +};
> +
> +int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /
> + sizeof(bb_miiphy_buses[0]);
static? And can you use ARRAY_SIZE()?
> +#endif
Perhaps its also a good idea to move at least some of this code
(especiall the command and perhaps some MDIO stuff) into separate
files that are only compiled for non-SPL U-Boot. This will remove
some of the #ifdefs as well.
> diff --git a/board/gdsys/38x/dt_helpers.c b/board/gdsys/38x/dt_helpers.c
> new file mode 100644
> index 0000000..dedd048
> --- /dev/null
> +++ b/board/gdsys/38x/dt_helpers.c
> @@ -0,0 +1,60 @@
> +/*
> + * (C) Copyright 2016
> + * Mario Six, Guntermann & Drunck GmbH, mario.six at gdsys.cc
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <i2c.h>
> +#include <dm.h>
> +#include <fdt_support.h>
> +#include <asm-generic/gpio.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +bool get_gpio(char *name, struct gpio_desc *gpio)
> +{
> + int node = fdt_node_offset_by_compatible(gd->fdt_blob, 0, name);
> + int ret;
> +
> + if (node < 0)
> + return false;
> +
> + ret = gpio_request_by_name_nodev(gd->fdt_blob, node, "gpios", 0, gpio,
> + 0);
> +
> + if (ret < 0)
> + return false;
> +
> + return dm_gpio_is_valid(gpio);
> +}
> +
> +int fdt_disable_by_ofname(char *ofname)
> +{
> + void *blob = gd->fdt_blob;
> + int offset;
> +
> + offset = fdt_path_offset(blob, ofname);
> + return fdt_status_disabled(blob, offset);
> +}
> +
> +struct udevice *dev_get_by_ofname(char *ofname)
> +{
> + void *blob = gd->fdt_blob;
> + int offset;
> + struct udevice *dev;
> +
> + offset = fdt_path_offset(blob, ofname);
> + device_get_global_by_of_offset(offset, &dev);
> +
> + return dev;
> +}
> +
> +bool dm_i2c_simple_probe(struct udevice *bus, uint chip_addr)
> +{
> + struct udevice *dev;
> +
> + return !dm_i2c_probe(bus, chip_addr, DM_I2C_CHIP_RD_ADDRESS |
> + DM_I2C_CHIP_WR_ADDRESS, &dev);
> +}
At least some of this might be very helpful as common U-Boot
functions available for all boards.
> diff --git a/board/gdsys/38x/dt_helpers.h b/board/gdsys/38x/dt_helpers.h
> new file mode 100644
> index 0000000..8052b94
> --- /dev/null
> +++ b/board/gdsys/38x/dt_helpers.h
> @@ -0,0 +1,16 @@
> +/*
> + * (C) Copyright 2016
> + * Mario Six, Guntermann & Drunck GmbH, mario.six at gdsys.cc
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __DT_HELPERS_H
> +#define __DT_HELPERS_H
> +
> +bool get_gpio(char *name, struct gpio_desc *gpio);
> +int fdt_disable_by_ofname(char *ofname);
> +struct udevice *dev_get_by_ofname(char *ofname);
> +bool dm_i2c_simple_probe(struct udevice *bus, uint chip_addr);
> +
> +#endif /* __DT_HELPERS_H */
> diff --git a/board/gdsys/38x/hre.c b/board/gdsys/38x/hre.c
> new file mode 100644
> index 0000000..10bf1a0
> --- /dev/null
> +++ b/board/gdsys/38x/hre.c
> @@ -0,0 +1,517 @@
> +/*
> + * (C) Copyright 2013
> + * Reinhard Pfau, Guntermann & Drunck GmbH, reinhard.pfau at gdsys.cc
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <malloc.h>
> +#include <fs.h>
> +#include <i2c.h>
> +#include <mmc.h>
> +#include <tpm.h>
> +#include <u-boot/sha1.h>
> +#include <asm/byteorder.h>
> +#include <asm/unaligned.h>
> +#include <pca9698.h>
> +
> +#include "hre.h"
> +
> +/* other constants */
> +enum {
> + ESDHC_BOOT_IMAGE_SIG_OFS = 0x40,
> + ESDHC_BOOT_IMAGE_SIZE_OFS = 0x48,
> + ESDHC_BOOT_IMAGE_ADDR_OFS = 0x50,
> + ESDHC_BOOT_IMAGE_TARGET_OFS = 0x58,
> + ESDHC_BOOT_IMAGE_ENTRY_OFS = 0x60,
> +};
> +
> +enum {
> + I2C_SOC_0 = 0,
> + I2C_SOC_1 = 1,
> +};
> +
> +enum access_mode {
> + HREG_NONE = 0,
> + HREG_RD = 1,
> + HREG_WR = 2,
> + HREG_RDWR = 3,
> +};
> +
> +/* register constants */
> +enum {
> + FIX_HREG_DEVICE_ID_HASH = 0,
> + FIX_HREG_UNUSED1 = 1,
> + FIX_HREG_UNUSED2 = 2,
> + FIX_HREG_VENDOR = 3,
> + COUNT_FIX_HREGS
> +};
> +
> +static struct h_reg pcr_hregs[24];
> +static struct h_reg fix_hregs[COUNT_FIX_HREGS];
> +static struct h_reg var_hregs[8];
> +
> +/* hre opcodes */
> +enum {
> + /* opcodes w/o data */
> + HRE_NOP = 0x00,
> + HRE_SYNC = HRE_NOP,
> + HRE_CHECK0 = 0x01,
> + /* opcodes w/o data, w/ sync dst */
> + /* opcodes w/ data */
> + HRE_LOAD = 0x81,
> + /* opcodes w/data, w/sync dst */
> + HRE_XOR = 0xC1,
> + HRE_AND = 0xC2,
> + HRE_OR = 0xC3,
> + HRE_EXTEND = 0xC4,
> + HRE_LOADKEY = 0xC5,
> +};
> +
> +/* hre errors */
> +enum {
> + HRE_E_OK = 0,
> + HRE_E_TPM_FAILURE,
> + HRE_E_INVALID_HREG,
> +};
> +
> +static uint64_t device_id;
> +static uint64_t device_cl;
> +static uint64_t device_type;
> +
> +static uint32_t platform_key_handle;
> +
> +static uint32_t hre_tpm_err;
> +static int hre_err = HRE_E_OK;
> +
> +#define IS_PCR_HREG(spec) ((spec) & 0x20)
> +#define IS_FIX_HREG(spec) (((spec) & 0x38) == 0x08)
> +#define IS_VAR_HREG(spec) (((spec) & 0x38) == 0x10)
> +#define HREG_IDX(spec) ((spec) & (IS_PCR_HREG(spec) ? 0x1f : 0x7))
> +
> +static const uint8_t vendor[] = "Guntermann & Drunck";
> +
> +/**
> + * @brief get the size of a given (TPM) NV area
> + * @param index NV index of the area to get size for
> + * @param size pointer to the size
> + * @return 0 on success, != 0 on error
> + */
> +static int get_tpm_nv_size(uint32_t index, uint32_t *size)
> +{
> + uint32_t err;
> + uint8_t info[72];
> + uint8_t *ptr;
> + uint16_t v16;
> +
> + err = tpm_get_capability(TPM_CAP_NV_INDEX, index,
> + info, sizeof(info));
> + if (err) {
> + printf("tpm_get_capability(CAP_NV_INDEX, %08x) failed: %u\n",
> + index, err);
> + return 1;
> + }
> +
> + /* skip tag and nvIndex */
> + ptr = info + 6;
> + /* skip 2 pcr info fields */
> + v16 = get_unaligned_be16(ptr);
> + ptr += 2 + v16 + 1 + 20;
> + v16 = get_unaligned_be16(ptr);
> + ptr += 2 + v16 + 1 + 20;
> + /* skip permission and flags */
> + ptr += 6 + 3;
> +
> + *size = get_unaligned_be32(ptr);
> + return 0;
> +}
> +
> +/**
> + * @brief search for a key by usage auth and pub key hash.
> + * @param auth usage auth of the key to search for
> + * @param pubkey_digest (SHA1) hash of the pub key structure of the key
> + * @param[out] handle the handle of the key iff found
> + * @return 0 if key was found in TPM; != 0 if not.
> + */
> +static int find_key(const uint8_t auth[20], const uint8_t pubkey_digest[20],
> + uint32_t *handle)
> +{
> + uint16_t key_count;
> + uint32_t key_handles[10];
> + uint8_t buf[288];
> + uint8_t *ptr;
> + uint32_t err;
> + uint8_t digest[20];
> + size_t buf_len;
> + unsigned int i;
> +
> + /* fetch list of already loaded keys in the TPM */
> + err = tpm_get_capability(TPM_CAP_HANDLE, TPM_RT_KEY, buf, sizeof(buf));
> + if (err)
> + return -1;
> + key_count = get_unaligned_be16(buf);
> + ptr = buf + 2;
> + for (i = 0; i < key_count; ++i, ptr += 4)
> + key_handles[i] = get_unaligned_be32(ptr);
> +
> + /* now search a(/ the) key which we can access with the given auth */
> + for (i = 0; i < key_count; ++i) {
> + buf_len = sizeof(buf);
> + err = tpm_get_pub_key_oiap(key_handles[i], auth, buf, &buf_len);
> + if (err && err != TPM_AUTHFAIL)
> + return -1;
> + if (err)
> + continue;
> + sha1_csum(buf, buf_len, digest);
> + if (!memcmp(digest, pubkey_digest, 20)) {
> + *handle = key_handles[i];
> + return 0;
> + }
> + }
> + return 1;
> +}
> +
> +/**
> + * @brief read CCDM common data from TPM NV
> + * @return 0 if CCDM common data was found and read, !=0 if something failed.
> + */
> +static int read_common_data(void)
> +{
> + uint32_t size = 0;
> + uint32_t err;
> + uint8_t buf[256];
> + sha1_context ctx;
> +
> + if (get_tpm_nv_size(NV_COMMON_DATA_INDEX, &size) ||
> + size < NV_COMMON_DATA_MIN_SIZE)
> + return 1;
> + err = tpm_nv_read_value(NV_COMMON_DATA_INDEX,
> + buf, min(sizeof(buf), size));
> + if (err) {
> + printf("tpm_nv_read_value() failed: %u\n", err);
> + return 1;
> + }
> +
> + device_id = get_unaligned_be64(buf);
> + device_cl = get_unaligned_be64(buf + 8);
> + device_type = get_unaligned_be64(buf + 16);
> +
> + sha1_starts(&ctx);
> + sha1_update(&ctx, buf, 24);
> + sha1_finish(&ctx, fix_hregs[FIX_HREG_DEVICE_ID_HASH].digest);
> + fix_hregs[FIX_HREG_DEVICE_ID_HASH].valid = true;
> +
> + platform_key_handle = get_unaligned_be32(buf + 24);
> +
> + return 0;
> +}
> +
> +/**
> + * @brief get pointer to hash register by specification
> + * @param spec specification of a hash register
> + * @return pointer to hash register or NULL if @a spec does not qualify a
> + * valid hash register; NULL else.
> + */
> +static struct h_reg *get_hreg(uint8_t spec)
> +{
> + uint8_t idx;
> +
> + idx = HREG_IDX(spec);
> + if (IS_FIX_HREG(spec)) {
> + if (idx < ARRAY_SIZE(fix_hregs))
> + return fix_hregs + idx;
> + hre_err = HRE_E_INVALID_HREG;
> + } else if (IS_PCR_HREG(spec)) {
> + if (idx < ARRAY_SIZE(pcr_hregs))
> + return pcr_hregs + idx;
> + hre_err = HRE_E_INVALID_HREG;
> + } else if (IS_VAR_HREG(spec)) {
> + if (idx < ARRAY_SIZE(var_hregs))
> + return var_hregs + idx;
> + hre_err = HRE_E_INVALID_HREG;
> + }
> + return NULL;
> +}
> +
> +/**
> + * @brief get pointer of a hash register by specification and usage.
> + * @param spec specification of a hash register
> + * @param mode access mode (read or write or read/write)
> + * @return pointer to hash register if found and valid; NULL else.
> + *
> + * This func uses @a get_reg() to determine the hash register for a given spec.
> + * If a register is found it is validated according to the desired access mode.
> + * The value of automatic registers (PCR register and fixed registers) is
> + * loaded or computed on read access.
> + */
> +static struct h_reg *access_hreg(uint8_t spec, enum access_mode mode)
> +{
> + struct h_reg *result;
> +
> + result = get_hreg(spec);
> + if (!result)
> + return NULL;
> +
> + if (mode & HREG_WR) {
> + if (IS_FIX_HREG(spec)) {
> + hre_err = HRE_E_INVALID_HREG;
> + return NULL;
> + }
> + }
> + if (mode & HREG_RD) {
> + if (!result->valid) {
> + if (IS_PCR_HREG(spec)) {
> + hre_tpm_err = tpm_pcr_read(HREG_IDX(spec),
> + result->digest, 20);
> + result->valid = (hre_tpm_err == TPM_SUCCESS);
> + } else if (IS_FIX_HREG(spec)) {
> + switch (HREG_IDX(spec)) {
> + case FIX_HREG_DEVICE_ID_HASH:
> + read_common_data();
> + break;
> + case FIX_HREG_VENDOR:
> + memcpy(result->digest, vendor, 20);
> + result->valid = true;
> + break;
> + }
> + } else {
> + result->valid = true;
> + }
> + }
> + if (!result->valid) {
> + hre_err = HRE_E_INVALID_HREG;
> + return NULL;
> + }
> + }
> +
> + return result;
> +}
> +
> +static void *compute_and(void *_dst, const void *_src, size_t n)
> +{
> + uint8_t *dst = _dst;
> + const uint8_t *src = _src;
> + size_t i;
> +
> + for (i = n; i-- > 0; )
> + *dst++ &= *src++;
> +
> + return _dst;
> +}
> +
> +static void *compute_or(void *_dst, const void *_src, size_t n)
> +{
> + uint8_t *dst = _dst;
> + const uint8_t *src = _src;
> + size_t i;
> +
> + for (i = n; i-- > 0; )
> + *dst++ |= *src++;
> +
> + return _dst;
> +}
> +
> +static void *compute_xor(void *_dst, const void *_src, size_t n)
> +{
> + uint8_t *dst = _dst;
> + const uint8_t *src = _src;
> + size_t i;
> +
> + for (i = n; i-- > 0; )
> + *dst++ ^= *src++;
> +
> + return _dst;
> +}
> +
> +static void *compute_extend(void *_dst, const void *_src, size_t n)
> +{
> + uint8_t digest[20];
> + sha1_context ctx;
> +
> + sha1_starts(&ctx);
> + sha1_update(&ctx, _dst, n);
> + sha1_update(&ctx, _src, n);
> + sha1_finish(&ctx, digest);
> + memcpy(_dst, digest, min(n, sizeof(digest)));
> +
> + return _dst;
> +}
> +
> +static int hre_op_loadkey(struct h_reg *src_reg, struct h_reg *dst_reg,
> + const void *key, size_t key_size)
> +{
> + uint32_t parent_handle;
> + uint32_t key_handle;
> +
> + if (!src_reg || !dst_reg || !src_reg->valid || !dst_reg->valid)
> + return -1;
> + if (find_key(src_reg->digest, dst_reg->digest, &parent_handle))
> + return -1;
> + hre_tpm_err = tpm_load_key2_oiap(parent_handle, key, key_size,
> + src_reg->digest, &key_handle);
> + if (hre_tpm_err) {
> + hre_err = HRE_E_TPM_FAILURE;
> + return -1;
> + }
> + /* TODO remember key handle somehow? */
Is this comment still valid?
> +
> + return 0;
> +}
> +
> +/**
> + * @brief executes the next opcode on the hash register engine.
> + * @param[in,out] ip pointer to the opcode (instruction pointer)
> + * @param[in,out] code_size (remaining) size of the code
> + * @return new instruction pointer on success, NULL on error.
> + */
> +static const uint8_t *hre_execute_op(const uint8_t **ip, size_t *code_size)
> +{
> + bool dst_modified = false;
> + uint32_t ins;
> + uint8_t opcode;
> + uint8_t src_spec;
> + uint8_t dst_spec;
> + uint16_t data_size;
> + struct h_reg *src_reg, *dst_reg;
> + uint8_t buf[20];
> + const uint8_t *src_buf, *data;
> + uint8_t *ptr;
> + int i;
> + void * (*bin_func)(void *, const void *, size_t);
> +
> + if (*code_size < 4)
> + return NULL;
> +
> + ins = get_unaligned_be32(*ip);
> + opcode = **ip;
> + data = *ip + 4;
> + src_spec = (ins >> 18) & 0x3f;
> + dst_spec = (ins >> 12) & 0x3f;
> + data_size = (ins & 0x7ff);
> +
> + debug("HRE: ins=%08x (op=%02x, s=%02x, d=%02x, L=%d)\n", ins,
> + opcode, src_spec, dst_spec, data_size);
> +
> + if ((opcode & 0x80) && (data_size + 4) > *code_size)
> + return NULL;
> +
> + src_reg = access_hreg(src_spec, HREG_RD);
> + if (hre_err || hre_tpm_err)
> + return NULL;
> + dst_reg = access_hreg(dst_spec, (opcode & 0x40) ? HREG_RDWR : HREG_WR);
> + if (hre_err || hre_tpm_err)
> + return NULL;
> +
> + switch (opcode) {
> + case HRE_NOP:
> + goto end;
> + case HRE_CHECK0:
> + if (src_reg) {
> + for (i = 0; i < 20; ++i) {
> + if (src_reg->digest[i])
> + return NULL;
> + }
> + }
> + break;
> + case HRE_LOAD:
> + bin_func = memcpy;
> + goto do_bin_func;
> + case HRE_XOR:
> + bin_func = compute_xor;
> + goto do_bin_func;
> + case HRE_AND:
> + bin_func = compute_and;
> + goto do_bin_func;
> + case HRE_OR:
> + bin_func = compute_or;
> + goto do_bin_func;
> + case HRE_EXTEND:
> + bin_func = compute_extend;
> +do_bin_func:
> + if (!dst_reg)
> + return NULL;
> + if (src_reg) {
> + src_buf = src_reg->digest;
> + } else {
> + if (!data_size) {
> + memset(buf, 0, 20);
> + src_buf = buf;
> + } else if (data_size == 1) {
> + memset(buf, *data, 20);
> + src_buf = buf;
> + } else if (data_size >= 20) {
> + src_buf = data;
> + } else {
> + src_buf = buf;
> + for (ptr = (uint8_t *)src_buf, i = 20; i > 0;
> + i -= data_size, ptr += data_size)
> + memcpy(ptr, data,
> + min_t(size_t, i, data_size));
> + }
> + }
> + bin_func(dst_reg->digest, src_buf, 20);
> + dst_reg->valid = true;
> + dst_modified = true;
> + break;
> + case HRE_LOADKEY:
> + if (hre_op_loadkey(src_reg, dst_reg, data, data_size))
> + return NULL;
> + break;
> + default:
> + return NULL;
> + }
> +
> + if (dst_reg && dst_modified && IS_PCR_HREG(dst_spec)) {
> + hre_tpm_err = tpm_extend(HREG_IDX(dst_spec), dst_reg->digest,
> + dst_reg->digest);
> + if (hre_tpm_err) {
> + hre_err = HRE_E_TPM_FAILURE;
> + return NULL;
> + }
> + }
> +end:
> + *ip += 4;
> + *code_size -= 4;
> + if (opcode & 0x80) {
> + *ip += data_size;
> + *code_size -= data_size;
> + }
> +
> + return *ip;
> +}
> +
> +/**
> + * @brief runs a program on the hash register engine.
> + * @param code pointer to the (HRE) code.
> + * @param code_size size of the code (in bytes).
> + * @return 0 on success, != 0 on failure.
> + */
> +int hre_run_program(const uint8_t *code, size_t code_size)
> +{
> + size_t code_left;
> + const uint8_t *ip = code;
> +
> + code_left = code_size;
> + hre_tpm_err = 0;
> + hre_err = HRE_E_OK;
> + while (code_left > 0)
> + if (!hre_execute_op(&ip, &code_left))
> + return -1;
> +
> + return hre_err;
> +}
> +
> +int hre_verify_program(struct key_program *prg)
> +{
> + uint32_t crc;
> +
> + crc = crc32(0, prg->code, prg->code_size);
> +
> + if (crc != prg->code_crc) {
> + printf("HRC crc mismatch: %08x != %08x\n",
> + crc, prg->code_crc);
> + return 1;
> + }
> + return 0;
> +}
> diff --git a/board/gdsys/38x/hre.h b/board/gdsys/38x/hre.h
> new file mode 100644
> index 0000000..84ce279
> --- /dev/null
> +++ b/board/gdsys/38x/hre.h
> @@ -0,0 +1,38 @@
> +/*
> + * (C) Copyright 2013
> + * Reinhard Pfau, Guntermann & Drunck GmbH, reinhard.pfau at gdsys.cc
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __HRE_H
> +#define __HRE_H
> +
> +struct key_program {
> + uint32_t magic;
> + uint32_t code_crc;
> + uint32_t code_size;
> + uint8_t code[];
> +};
> +
> +struct h_reg {
> + bool valid;
> + uint8_t digest[20];
> +};
> +
> +/* CCDM specific contants */
> +enum {
> + /* NV indices */
> + NV_COMMON_DATA_INDEX = 0x40000001,
> + /* magics for key blob chains */
> + MAGIC_KEY_PROGRAM = 0x68726500,
> + MAGIC_HMAC = 0x68616300,
> + MAGIC_END_OF_CHAIN = 0x00000000,
> + /* sizes */
> + NV_COMMON_DATA_MIN_SIZE = 3 * sizeof(uint64_t) + 2 * sizeof(uint16_t),
> +};
> +
> +int hre_verify_program(struct key_program *prg);
> +int hre_run_program(const uint8_t *code, size_t code_size);
> +
> +#endif /* __HRE_H */
> diff --git a/board/gdsys/38x/keyprogram.c b/board/gdsys/38x/keyprogram.c
> new file mode 100644
> index 0000000..a4a6f1c
> --- /dev/null
> +++ b/board/gdsys/38x/keyprogram.c
> @@ -0,0 +1,158 @@
> +/*
> + * (C) Copyright 2016
> + * Mario Six, Guntermann & Drunck GmbH, mario.six at gdsys.cc
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <tpm.h>
> +#include <malloc.h>
> +#include <linux/ctype.h>
> +#include <asm/unaligned.h>
> +
> +#include "hre.h"
> +
> +int flush_keys(void)
> +{
> + u16 key_count;
> + u8 buf[288];
> + u8 *ptr;
> + u32 err;
> + uint i;
> +
> + /* fetch list of already loaded keys in the TPM */
> + err = tpm_get_capability(TPM_CAP_HANDLE, TPM_RT_KEY, buf, sizeof(buf));
> + if (err)
> + return -1;
> + key_count = get_unaligned_be16(buf);
> + ptr = buf + 2;
> + for (i = 0; i < key_count; ++i, ptr += 4) {
> + err = tpm_flush_specific(get_unaligned_be32(ptr), TPM_RT_KEY);
> + if (err && err != TPM_KEY_OWNER_CONTROL)
> + return err;
> + }
> +
> + return 0;
> +}
> +
> +int decode_hexstr(char *hexstr, u8 **result)
> +{
> + int len = strlen(hexstr);
> + int bytes = len / 2;
> + int i;
> + u8 acc = 0;
> +
> + if (len % 2 == 1)
> + return 1;
> +
> + *result = (u8 *)malloc(bytes);
> +
> + for (i = 0; i < len; i++) {
> + char cur = tolower(hexstr[i]);
> + u8 val;
> +
> + if ((cur >= 'a' && cur <= 'f') || (cur >= '0' && cur <= '9')) {
> + val = cur - (cur > '9' ? 87 : 48);
> +
> + if (i % 2 == 0)
> + acc = 16 * val;
> + else
> + (*result)[i / 2] = acc + val;
> + } else {
> + free(*result);
> + return 1;
> + }
> + }
> +
> + return 0;
> +}
> +
> +int extract_subprogram(u8 **progdata, u32 expected_magic,
> + struct key_program **result)
> +{
> + struct key_program *prog = *result;
> + u32 magic, code_crc, code_size;
> +
> + magic = get_unaligned_be32(*progdata);
> + code_crc = get_unaligned_be32(*progdata + 4);
> + code_size = get_unaligned_be32(*progdata + 8);
> +
> + *progdata += 12;
> +
> + if (magic != expected_magic)
> + return -1;
> +
> + *result = malloc(sizeof(struct key_program) + code_size);
> +
> + if (!*result)
> + return -1;
> +
> + prog->magic = magic;
> + prog->code_crc = code_crc;
> + prog->code_size = code_size;
> + memcpy(prog->code, *progdata, code_size);
> +
> + *progdata += code_size;
> +
> + if (hre_verify_program(prog)) {
> + free(prog);
> + return -1;
> + }
> +
> + return 0;
> +}
> +
> +struct key_program *parse_and_check_keyprog(u8 *progdata)
> +{
> + struct key_program *result = NULL, *hmac = NULL;
> +
> + /* Part 1: Load key program */
> +
> + if (extract_subprogram(&progdata, MAGIC_KEY_PROGRAM, &result))
> + return NULL;
> +
> + /* Part 2: Load hmac program */
> +
> + if (extract_subprogram(&progdata, MAGIC_HMAC, &hmac))
> + return NULL;
> +
> + free(hmac);
> +
> + return result;
> +}
> +
> +int load_and_run_keyprog(void)
> +{
> + char *cmd = NULL;
> + u8 *binprog = NULL;
> + char *hexprog;
> + struct key_program *prog;
> +
> + cmd = getenv("loadkeyprogram");
> +
> + if (!cmd || run_command(cmd, 0))
> + return 1;
> +
> + hexprog = getenv("keyprogram");
> +
> + if (decode_hexstr(hexprog, &binprog))
> + return 1;
> +
> + prog = parse_and_check_keyprog(binprog);
> + free(binprog);
> +
> + if (!prog)
> + return 1;
> +
> + if (hre_run_program(prog->code, prog->code_size)) {
> + free(prog);
> + return 1;
> + }
> +
> + printf("\nSD code ran successfully\n");
> +
> + free(prog);
> +
> + return 0;
> +}
> diff --git a/board/gdsys/38x/keyprogram.h b/board/gdsys/38x/keyprogram.h
> new file mode 100644
> index 0000000..a5ea7d3
> --- /dev/null
> +++ b/board/gdsys/38x/keyprogram.h
> @@ -0,0 +1,14 @@
> +/*
> + * (C) Copyright 2016
> + * Mario Six, Guntermann & Drunck GmbH, mario.six at gdsys.cc
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __KEYPROGRAM_H
> +#define __KEYPROGRAM_H
> +
> +int load_and_run_keyprog(void);
> +int flush_keys(void);
> +
> +#endif /* __KEYPROGRAM_H */
> diff --git a/board/gdsys/38x/kwbimage.cfg.in b/board/gdsys/38x/kwbimage.cfg.in
> new file mode 100644
> index 0000000..72e67d7
> --- /dev/null
> +++ b/board/gdsys/38x/kwbimage.cfg.in
> @@ -0,0 +1,12 @@
> +#
> +# Copyright (C) 2014 Stefan Roese <sr at denx.de>
> +#
> +
> +# Armada 38x uses version 1 image format
> +VERSION 1
> +
> +# Boot Media configurations
> +#@BOOT_FROM
> +
> +# Binary Header (bin_hdr) with DDR3 training code
> +BINARY spl/u-boot-spl.bin 0000005b 00000068
> diff --git a/board/gdsys/38x/spl.c b/board/gdsys/38x/spl.c
> new file mode 100644
> index 0000000..2d05a9c
> --- /dev/null
> +++ b/board/gdsys/38x/spl.c
> @@ -0,0 +1,21 @@
> +/*
> + * (C) Copyright 2016
> + * Mario Six, Guntermann & Drunck GmbH, mario.six at gdsys.cc
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <config.h>
> +#include <asm/arch/cpu.h>
> +
> +void spl_board_init(void)
> +{
> +#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH
> + u32 *bootrom_save = (u32 *)CONFIG_SPL_BOOTROM_SAVE;
> + u32 *regs = (u32 *)(*bootrom_save);
> +
> + printf("Returning to BootROM (return address %08x)...\n", regs[13]);
> + return_to_bootrom();
> +#endif
> +}
> diff --git a/configs/controlcenterdc_defconfig b/configs/controlcenterdc_defconfig
> new file mode 100644
> index 0000000..ee06c84
> --- /dev/null
> +++ b/configs/controlcenterdc_defconfig
> @@ -0,0 +1,54 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_MVEBU=y
> +CONFIG_SPL_GPIO_SUPPORT=y
> +CONFIG_SYS_MALLOC_F_LEN=0x2000
> +CONFIG_TARGET_CONTROLCENTERDC=y
> +CONFIG_SPL_SPI_FLASH_SUPPORT=y
> +CONFIG_SPL_SPI_SUPPORT=y
> +CONFIG_DEFAULT_DEVICE_TREE="controlcenterdc"
> +CONFIG_FIT=y
> +CONFIG_FIT_VERBOSE=y
> +CONFIG_FIT_SIGNATURE=y
> +CONFIG_SYS_CONSOLE_INFO_QUIET=y
> +CONFIG_SPL=y
> +CONFIG_SPL_SYS_MALLOC_SIMPLE=y
> +CONFIG_HUSH_PARSER=y
> +# CONFIG_CMD_ELF is not set
> +# CONFIG_CMD_GO is not set
> +# CONFIG_CMD_IMLS is not set
> +# CONFIG_CMD_FLASH is not set
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_SF=y
> +CONFIG_CMD_USB=y
> +CONFIG_CMD_GPIO=y
> +# CONFIG_CMD_SETEXPR is not set
> +CONFIG_CMD_DHCP=y
> +CONFIG_CMD_PING=y
> +CONFIG_CMD_CACHE=y
> +CONFIG_CMD_TIME=y
> +CONFIG_CMD_TPM=y
> +CONFIG_CMD_EXT2=y
> +CONFIG_CMD_EXT4=y
> +CONFIG_OF_BOARD_FIXUP=y
> +CONFIG_SPL_OF_TRANSLATE=y
> +CONFIG_DM_GPIO=y
> +CONFIG_DM_PCA953X=y
> +CONFIG_DM_I2C=y
> +CONFIG_SYS_I2C_MVTWSI=y
> +CONFIG_LED=y
> +CONFIG_LED_GPIO=y
> +CONFIG_SPI_FLASH=y
> +CONFIG_SPI_FLASH_STMICRO=y
> +CONFIG_DEBUG_UART=y
> +CONFIG_DEBUG_UART_BASE=0xd0012000
> +CONFIG_DEBUG_UART_CLOCK=250000000
> +CONFIG_DEBUG_UART_SHIFT=2
> +CONFIG_SYS_NS16550=y
> +CONFIG_TPM_ATMEL_TWI=y
> +CONFIG_TPM_AUTH_SESSIONS=y
> +CONFIG_USB=y
> +CONFIG_DM_USB=y
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_STORAGE=y
> +CONFIG_TPM=y
> +# CONFIG_EFI_LOADER is not set
> diff --git a/include/configs/controlcenterdc.h b/include/configs/controlcenterdc.h
> new file mode 100644
> index 0000000..9097dce
> --- /dev/null
> +++ b/include/configs/controlcenterdc.h
> @@ -0,0 +1,244 @@
> +/*
> + * Copyright (C) 2014 Stefan Roese <sr at denx.de>
> + * Copyright (C) 2016 Mario Six <mario.six at gdsys.cc>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef _CONFIG_CONTROLCENTERDC_H
> +#define _CONFIG_CONTROLCENTERDC_H
> +
> +/*
> + * High Level Configuration Options (easy to change)
> + */
> +#define CONFIG_CUSTOMER_BOARD_SUPPORT
> +
> +#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
> +#define CONFIG_DISPLAY_BOARDINFO_LATE
> +#define CONFIG_BOARD_LATE_INIT
> +#define CONFIG_LAST_STAGE_INIT
> +#define CONFIG_SPL_BOARD_INIT
> +
> +/*
> + * TEXT_BASE needs to be below 16MiB, since this area is scrubbed
> + * for DDR ECC byte filling in the SPL before loading the main
> + * U-Boot into it.
> + */
> +#define CONFIG_SYS_TEXT_BASE 0x00800000
> +
> +#define CONFIG_SYS_TCLK 250000000 /* 250MHz */
> +
> +#define CONFIG_LOADADDR 1000000
> +
> +#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
> +
> +/*
> + * Commands configuration
> + */
> +#define CONFIG_CMD_ENV
> +#define CONFIG_CMD_I2C
> +#define CONFIG_CMD_PCI
> +#define CONFIG_CMD_SCSI
> +#define CONFIG_CMD_SPI
> +
> +/* SPI NOR flash default params, used by sf commands */
> +#define CONFIG_SF_DEFAULT_BUS 1
> +#define CONFIG_SF_DEFAULT_SPEED 1000000
> +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3
> +
> +/*
> + * SDIO/MMC Card Configuration
> + */
> +#define CONFIG_MMC
> +#define CONFIG_GENERIC_MMC
> +#define CONFIG_SDHCI
> +#define CONFIG_MV_SDHCI
> +#define CONFIG_SYS_MMC_BASE MVEBU_SDIO_BASE
> +
> +/*
> + * SATA/SCSI/AHCI configuration
> + */
> +#define CONFIG_LIBATA
> +#define CONFIG_SCSI
> +#define CONFIG_SCSI_AHCI
> +#define CONFIG_SCSI_AHCI_PLAT
> +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 2
> +#define CONFIG_SYS_SCSI_MAX_LUN 1
> +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
> + CONFIG_SYS_SCSI_MAX_LUN)
> +
> +/* Partition support */
> +#define CONFIG_DOS_PARTITION
> +#define CONFIG_EFI_PARTITION
> +
> +/* Additional FS support/configuration */
> +#define CONFIG_SUPPORT_VFAT
> +
> +/* USB/EHCI configuration */
> +#define CONFIG_EHCI_IS_TDI
> +
> +/* Environment in SPI NOR flash */
> +#define CONFIG_ENV_IS_IN_SPI_FLASH
> +#define CONFIG_ENV_SPI_BUS 1
> +#define CONFIG_ENV_OFFSET (1 << 20) /* 1MiB in */
> +#define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */
> +#define CONFIG_ENV_SECT_SIZE (256 << 10) /* 256KiB sectors */
> +
> +#define CONFIG_PHY_MARVELL /* there is a marvell phy */
> +#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */
> +
> +/* PCIe support */
> +#ifndef CONFIG_SPL_BUILD
> +#define CONFIG_PCI
> +#define CONFIG_PCI_MVEBU
> +#define CONFIG_PCI_PNP
> +#define CONFIG_PCI_SCAN_SHOW
> +#endif
> +
> +#define CONFIG_SYS_ALT_MEMTEST
> +
> +/*
> + * Software (bit-bang) MII driver configuration
> + */
> +#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
> +#define CONFIG_BITBANGMII_MULTI
> +
> +/*
> + * GPIO
> + */
> +#define CONFIG_KIRKWOOD_GPIO
> +
> +/* SPL */
> +/*
> + * Select the boot device here
> + *
> + * Currently supported are:
> + * SPL_BOOT_SPI_NOR_FLASH - Booting via SPI NOR flash
> + * SPL_BOOT_SDIO_MMC_CARD - Booting via SDIO/MMC card (partition 1)
> + */
> +#define SPL_BOOT_SPI_NOR_FLASH 1
> +#define SPL_BOOT_SDIO_MMC_CARD 2
> +#define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SPI_NOR_FLASH
> +
> +/* Defines for SPL */
> +#define CONFIG_SPL_FRAMEWORK
> +#define CONFIG_SPL_SIZE (160 << 10)
> +
> +#if defined(CONFIG_SECURED_MODE_IMAGE)
> +#define CONFIG_SPL_TEXT_BASE 0x40002614
> +#define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x2614)
> +#else
> +#define CONFIG_SPL_TEXT_BASE 0x40000030
> +#define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x30)
> +#endif
> +
> +#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE)
> +#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10)
> +
> +#ifdef CONFIG_SPL_BUILD
> +#define CONFIG_SYS_MALLOC_SIMPLE
> +#endif
> +
> +#define CONFIG_SPL_STACK (0x40000000 + ((212 - 16) << 10))
> +#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
> +
> +#define CONFIG_SPL_LIBCOMMON_SUPPORT
> +#define CONFIG_SPL_LIBGENERIC_SUPPORT
> +#define CONFIG_SPL_SERIAL_SUPPORT
> +#define CONFIG_SPL_I2C_SUPPORT
> +
> +#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH
> +/* SPL related SPI defines */
> +#define CONFIG_SPL_SPI_LOAD
> +#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x30000
> +#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS
> +#endif
> +
> +#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD
> +/* SPL related MMC defines */
> +#define CONFIG_SPL_MMC_SUPPORT
> +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION 1
> +#define CONFIG_SYS_MMC_U_BOOT_OFFS (168 << 10)
> +#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_MMC_U_BOOT_OFFS
> +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR (CONFIG_SYS_U_BOOT_OFFS / 512)
> +#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS ((512 << 10) / 512) /* 512KiB */
> +#ifdef CONFIG_SPL_BUILD
> +#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER 0x00180000 /* in SDRAM */
> +#endif
> +#endif
> +
> +/*
> + * Environment Configuration
> + */
> +#define CONFIG_ENV_OVERWRITE
> +
> +#define CONFIG_BAUDRATE 115200
> +
> +#define CONFIG_HOSTNAME ccdc
> +#define CONFIG_ROOTPATH "/opt/nfsroot"
> +#define CONFIG_BOOTFILE "ccdc.img"
> +
> +#define CONFIG_PREBOOT /* enable preboot variable */
> +
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> + "netdev=eth1\0" \
> + "consoledev=ttyS1\0" \
> + "u-boot=u-boot.bin\0" \
> + "bootfile_addr=1000000\0" \
> + "keyprogram_addr=3000000\0" \
> + "keyprogram_file=keyprogram.img\0" \
> + "fdtfile=controlcenterdc.dtb\0" \
> + "load=tftpboot ${loadaddr} ${u-boot}\0" \
> + "mmcdev=0:2\0" \
> + "update=sf probe 1:0;" \
> + " sf erase 0 +${filesize};" \
> + " sf write ${fileaddr} 0 ${filesize}\0" \
> + "upd=run load update\0" \
> + "fdt_high=0x10000000\0" \
> + "initrd_high=0x10000000\0" \
> + "loadkeyprogram=tpm flush_keys;" \
> + " mmc rescan;" \
> + " ext4load mmc ${mmcdev} ${keyprogram_addr} ${keyprogram_file};"\
> + " source ${keyprogram_addr}:script at 1\0" \
> + "gpio1=gpio at 22_25\0" \
> + "gpio2=A29\0" \
> + "blinkseq='0 0 0 0 2 0 2 2 3 1 3 1 0 0 2 2 3 1 3 3 2 0 2 2 3 1 1 1 " \
> + "2 0 2 2 3 1 3 1 0 0 2 0 3 3 3 1 2 0 0 0 3 1 1 1 0 0 0 0'\0" \
> + "bootfail=for i in ${blinkseq}; do" \
> + " if test $i -eq 0; then" \
> + " gpio clear ${gpio1}; gpio set ${gpio2};" \
> + " elif test $i -eq 1; then" \
> + " gpio clear ${gpio1}; gpio clear ${gpio2};" \
> + " elif test $i -eq 2; then" \
> + " gpio set ${gpio1}; gpio set ${gpio2};" \
> + " else;" \
> + " gpio clear ${gpio1}; gpio set ${gpio2};" \
> + " fi; sleep 0.12; done\0"
> +
> +#define CONFIG_NFSBOOTCOMMAND \
> + "setenv bootargs root=/dev/nfs rw " \
> + "nfsroot=${serverip}:${rootpath} " \
> + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off " \
> + "console=${consoledev},${baudrate} ${othbootargs}; " \
> + "tftpboot ${bootfile_addr} ${bootfile}; " \
> + "bootm ${bootfile_addr}"
> +
> +#define CONFIG_MMCBOOTCOMMAND \
> + "setenv bootargs root=/dev/mmcblk0p3 rw rootwait " \
> + "console=${consoledev},${baudrate} ${othbootargs}; " \
> + "ext2load mmc 0:2 ${bootfile_addr} ${bootfile}; " \
> + "bootm ${bootfile_addr}"
> +
> +#define CONFIG_BOOTCOMMAND \
> + "if env exists keyprogram; then;" \
> + " setenv keyprogram; run nfsboot;" \
> + " fi;" \
> + " run dobootfail"
> +
> +/*
> + * mv-common.h should be defined after CMD configs since it used them
> + * to enable certain macros
> + */
> +#include "mv-common.h"
> +
> +#endif /* _CONFIG_CONTROLCENTERDC_H */
>
Thanks,
Stefan
More information about the U-Boot
mailing list