[U-Boot] [PATCH 09/14] net: Add ability to set MAC address via EEPROM

Olliver Schinagl oliver at schinagl.nl
Fri Dec 2 11:12:36 CET 2016


Hey Joe,


On 30-11-16 21:00, Joe Hershberger wrote:
> On Fri, Nov 25, 2016 at 9:30 AM, Olliver Schinagl <oliver at schinagl.nl> wrote:
>> This patch allows Kconfig to enable and set parameters to make it
>> possible to read the MAC address from an EEPROM. The net core layer then
>> uses this information to read MAC addresses from this EEPROM.
>>
>> Besides the various tuneables as to how to access the eeprom (bus,
>> address, addressing mode/length, 2 configurable that are EEPROM generic
>> (e.g. SPI or some other form of access) which are:
>>
>> NET_ETHADDR_EEPROM_OFFSET, indicating where in the EEPROM the start of
>> the MAC address is. The default is 8 allowing for 8 bytes before the MAC
>> for other purposes (header MAGIC for example).
>>
>> NET_ETHADDR_EEPROM_CRC8, indicating the MAC is appended with a CRC8-CCIT
>> checksum that should be verified.
>>
>> Currently only I2C eeproms have been tested and thus only those options
>> are available, but shouldn't be a limit. NET_ETHADDR_EEPROM_SPI can be
>> just as created and added.
>>
>> The code currently first checks if there is a non-zero MAC address in
>> the eeprom. If that fails to be the case, the read_rom_hwaddr can be
>> used by a board to supply the MAC in other ways.
>>
>> If both these fails, the other code is still in place to query the
>> environent, which then can be used to override the hardware supplied
>> data.
>>
>> Signed-off-by: Olliver Schinagl <oliver at schinagl.nl>
>> ---
>>   doc/README.enetaddr | 99 +++++++++++++++++++++++++++++++++++++++++++++++++++++
>>   include/net.h       | 14 ++++++++
>>   net/Kconfig         | 59 +++++++++++++++++++++++++++++++
>>   net/eth-uclass.c    |  9 +++--
>>   net/eth_common.c    | 34 ++++++++++++++++++
>>   net/eth_legacy.c    |  2 ++
>>   6 files changed, 214 insertions(+), 3 deletions(-)
>>
>> diff --git a/doc/README.enetaddr b/doc/README.enetaddr
>> index 50e4899..89c1f7d 100644
>> --- a/doc/README.enetaddr
>> +++ b/doc/README.enetaddr
>> @@ -47,6 +47,105 @@ Correct flow of setting up the MAC address (summarized):
>>   Previous behavior had the MAC address always being programmed into hardware
>>   in the device's init() function.
>>
>> +--------
>> + EEPROM
>> +--------
>> +
>> +Boards may come with an EEPROM specifically to store configuration bits, such
>> +as a MAC address. Using CONFIG_NET_ETHADDR_EEPROM enables this feature.
>> +Depending on the board, the EEPROM may be connected on various methods, but
>> +currently, only the I2C bus can be used via CONFIG_NET_ETHADDR_EEPROM_I2C.
>> +
>> +The following config options are available,
>> +CONFIG_NET_ETHADDR_EEPROM_I2C_BUS is the I2C bus on which the eeprom is present.
>> +CONFIG_NET_ETHADDR_EEPROM_I2C_ADDR sets the address of the EEPROM, which
>> +defaults to the very common 0x50. Small size EEPROM's generally use single byte
>> +addressing but larger EEPROM's may use double byte addressing, which can be
>> +configured using CONFIG_NET_ETHADDR_EEPROM_ADDRLEN.
>> +
>> +Within the EEPROM, the MAC address can be stored on any arbitrary offset,
>> +CONFIG_NET_ETHADDR_EEPROM_OFFSET sets this to 8 as a default however, allowing
>> +the first 8 bytes to be used for an optional data, for example a configuration
>> +struct where the mac address is part of.
>> +
>> +Appending the 6 (ARP_HLEN) bytes is a CRC8 byte over the previous ARP_HLEN
>> +bytes. Whether to check this CRC8 or not is dependent on
>> +CONFIG_NET_ETHADDR_EEPROM_CRC8.
>> +
>> +To keep things nicely aligned, a final 'reserved' byte is added to the mac
>> +address + crc8 combo.
>> +
>> +A board may want to store more information in its eeprom, using the following
>> +example layout, this can be achieved.
>> +
>> +struct mac_addr {
>> +       uint8_t mac[ARP_HLEN];
>> +       uint8_t crc8;
>> +       uint8_t reserved;
>> +};
>> +
>> +struct config_eeprom {
>> +       uint32_t magic;
>> +       uint8_t version;
>> +       uint8_t reserved[2];
>> +       uint8_t mac_cnt;
>> +       struct mac_addr[mac_cnt];
>> +};
>> +
>> +Filling this in:
>> +struct config_eeprom eeprom = {
>> +       .magic = { 'M', 'g', 'i', 'c' },
>> +       .reserved = { 0x00, 0x00 },
>> +       .mac_cnt = 2,
>> +       .mac_addr = {
>> +               {
>> +                       .mac = {
>> +                               0x01, 0x23, 0x45,
>> +                               0x67, 0x89, 0xab,
>> +                       },
>> +                       .crc8 = 0xbe,
>> +                       .reserved = 0x00,
>> +               }, {
>> +                       .mac = {
>> +                               0xba, 0x98, 0x76,
>> +                               0x54, 0x32, 0x10,
>> +                       },
>> +                       .crc8 = 0x82,
>> +                       .reserved = 0x00,
>> +               },
>> +       },
>> +};
>> +
>> +The eeprom content would look like this.
>> +
>> +00000000  4d 67 69 63 01 00 00 02  01 23 45 67 89 ab be 00 |Mgic.....#Eg....|
>> +00000010  ba 98 76 54 32 10 82 00                          |..vT2...|
>> +
>> +This can be done from linux using the i2c-tools:
>> +
>> +i2cset I2CBUS 0x50 0x08 0x01
>> +i2cset I2CBUS 0x50 0x09 0x23
>> +i2cset I2CBUS 0x50 0x0a 0x45
>> +i2cset I2CBUS 0x50 0x0b 0x67
>> +i2cset I2CBUS 0x50 0x0c 0x89
>> +i2cset I2CBUS 0x50 0x0d 0xab
>> +i2cset I2CBUS 0x50 0x0e 0xbe
>> +
>> +Alternativly this can be done from the u-boot console as:
>> +
>> +u-boot> mm.b 0
>> +00000000: 00 ? 01
>> +00000001: 23 ? 23
>> +00000002: 45 ? 45
>> +00000003: 67 ? 67
>> +00000004: 89 ? 89
>> +00000005: ab ? ab
>> +00000006: be ? be
>> +00000007: 00 ? q
>> +i2c dev I2CBUS
>> +i2c write 0 50 8 7
>> +i2c md 50 8
>> +
>>   -------
>>    Usage
>>   -------
>> diff --git a/include/net.h b/include/net.h
>> index 08f8af8..e50ab5d 100644
>> --- a/include/net.h
>> +++ b/include/net.h
>> @@ -248,6 +248,20 @@ int eth_getenv_enetaddr(const char *name, uchar *enetaddr);
>>   int eth_setenv_enetaddr(const char *name, const uchar *enetaddr);
>>
>>   /**
>> + * eeprom_read_enetaddr() - Read the hardware address from an eeprom
>> + *
>> + * This function tries to read the MAC address from an eeprom as can be read
>> + * in docs/README.enetaddr.
>> + *
>> + * @index:     index of the interface to get the hwaddr for
>> + * @enetaddr:  pointer for the found hwaddr. Needs to be atleast ARP_HLEN
>> + * @return:    0 on success, non-zero is error status. Additionally hwaddr
>> + *             is set to 00:00:00:00:00. This is also the case if
>> + *             CONFIG_NET_ETHADDR_EEPROM is not set.
>> + */
>> +int eeprom_read_enetaddr(const int index, unsigned char *enetaddr);
>> +
>> +/**
>>    * eth_setenv_enetaddr_by_index() - set the MAC address environment variable
>>    *
>>    * This sets up an environment variable with the given MAC address (@enetaddr).
>> diff --git a/net/Kconfig b/net/Kconfig
>> index 414c549..f699e1c 100644
>> --- a/net/Kconfig
>> +++ b/net/Kconfig
>> @@ -7,6 +7,65 @@ menuconfig NET
>>
>>   if NET
>>
>> +config NET_ETHADDR_EEPROM
>> +       bool "Get ethaddr from eeprom"
>> +       help
>> +         Selecting this will try to get the Ethernet address from an onboard
>> +         EEPROM and set into the environment if and only if the environment
>> +         does currently not already hold a MAC address. For more information
>> +         see doc/README.enetaddr.
>> +
>> +config NET_ETHADDR_EEPROM_I2C
>> +       depends on NET_ETHADDR_EEPROM
>> +       bool "EEPROM on I2C bus"
>> +       help
>> +         This switch enables checks for an EEPROM on the I2C bus. Naturally
>> +         this will only work if there is an actual EEPROM connected on the
>> +         I2C bus and the bus and device are properly configured via the
>> +         options below.
>> +
>> +config NET_ETHADDR_EEPROM_I2C_BUS
>> +       depends on NET_ETHADDR_EEPROM_I2C
>> +       int "I2C bus"
>> +       default 0
>> +       help
>> +         Select the bus on which the EEPROM is present, defaults to bus 0.
>> +         Remember to also make the selected bus available via I2Cn_ENABLE.
>> +
>> +config NET_ETHADDR_EEPROM_I2C_ADDR
>> +       depends on NET_ETHADDR_EEPROM_I2C
>> +       hex "EEPROM address"
>> +       default 0x50
>> +       help
>> +         Select the address of the EEPROM, defaults to address 0x50.
>> +
>> +config NET_ETHADDR_EEPROM_I2C_ADDRLEN
>> +       depends on NET_ETHADDR_EEPROM_I2C
>> +       int "EEPROM address length"
>> +       default 1
>> +       help
>> +         Number of bytes to be used for the I2C address length. Typically 1,
>> +         2 for large memories, 0 for register type devices with only one
>> +         register.
>> +
>> +config NET_ETHADDR_EEPROM_OFFSET
>> +       depends on NET_ETHADDR_EEPROM
>> +       int "EEPROM offset"
>> +       default 8
>> +       help
>> +         Select the byte offset of the MAC address within the page,
>> +         defaults to byte 8.
>> +
>> +config NET_ETHADDR_EEPROM_CRC8
>> +       depends on NET_ETHADDR_EEPROM
>> +       bool "Check CRC8 of MAC"
>> +       default y
>> +       help
>> +         Optionally, it is possible to run a CRC-8-CCITT check on the MAC
>> +         address. To do so, the MAC address is stored with a CRC8 byte append.
>> +         This option enables the CRC check of the MAC address against the CRC
>> +         byte.
>> +
>>   config NET_RANDOM_ETHADDR
>>          bool "Random ethaddr if unset"
>>          select LIB_RAND
>> diff --git a/net/eth-uclass.c b/net/eth-uclass.c
>> index 5c888b8..a154a7e 100644
>> --- a/net/eth-uclass.c
>> +++ b/net/eth-uclass.c
>> @@ -491,9 +491,12 @@ static int eth_post_probe(struct udevice *dev)
>>
>>          priv->state = ETH_STATE_INIT;
>>
>> -       /* Check if the device has a MAC address in ROM */
>> -       if (eth_get_ops(dev)->read_rom_hwaddr)
>> -               eth_get_ops(dev)->read_rom_hwaddr(dev);
>> +       /* Check if the device has a MAC address in EEPROM */
>> +       eeprom_read_enetaddr(dev->seq, pdata->enetaddr);
>> +       if (is_zero_ethaddr(pdata->enetaddr))
>> +               /* Check if the device has a MAC address in ROM */
>> +               if (eth_get_ops(dev)->read_rom_hwaddr)
>> +                       eth_get_ops(dev)->read_rom_hwaddr(dev);
>>
>>          eth_getenv_enetaddr_by_index("eth", dev->seq, env_enetaddr);
>>          if (!is_zero_ethaddr(env_enetaddr)) {
>> diff --git a/net/eth_common.c b/net/eth_common.c
>> index 079be89..e0d8b62 100644
>> --- a/net/eth_common.c
>> +++ b/net/eth_common.c
>> @@ -8,10 +8,44 @@
>>
>>   #include <common.h>
>>   #include <dm.h>
>> +#include <i2c.h>
>>   #include <miiphy.h>
>>   #include <net.h>
>>   #include "eth_internal.h"
>>
>> +int eeprom_read_enetaddr(const int index, unsigned char *enetaddr)
>> +{
>> +       uint8_t eeprom[ARP_HLEN + 1] = { 0x00 };
>> +#if defined(CONFIG_NET_ETHADDR_EEPROM) && defined(CONFIG_NET_ETHADDR_EEPROM_I2C)
> Since it is easily reasonable that SPI PROM is a likely useful
> support, why not keep the layout stuff separate from the I2C stuff so
> that it is trivial to plug in a different bus later? It will also make
> the code clearer by untangling these.

I strongly agree, but I recommend a follow up patch series (and thus 
merge this as is for now) to use Maxime's EEPROM framework patches. So 
then this gets replaced by simple read from eeprom.

So yes, I have contemplated in splitting it up now and have a simply 
read_from_i2c() kind of function, I figured this gets solved elsewhere 
anyway.

Additionally, the layout stuff would ideally be replaced by Igor (i 
think it was) eeprom layout framework (if those two combine) which 
solves both problems in one go.

Or you want to see it split now as the other is a bad plan (tm)?

Olliver
>
>> +       int old_i2c_bus;
>> +
>> +       old_i2c_bus = i2c_get_bus_num();
>> +       if (old_i2c_bus != CONFIG_NET_ETHADDR_EEPROM_I2C_BUS)
>> +               i2c_set_bus_num(CONFIG_NET_ETHADDR_EEPROM_I2C_BUS);
>> +       /* Skip in blocks of 8 (ARP + CRC8 + pad), but read 7 from the eeprom */
>> +       if (i2c_read(CONFIG_NET_ETHADDR_EEPROM_I2C_ADDR,
>> +                    CONFIG_NET_ETHADDR_EEPROM_OFFSET + (index * (ARP_HLEN + 2)),
>> +                    CONFIG_NET_ETHADDR_EEPROM_I2C_ADDRLEN,
>> +                    eeprom, ARP_HLEN + 1)) {
>> +               i2c_set_bus_num(old_i2c_bus);
>> +               puts("Could not read the EEPROM or EEPROM missing on device: ");
>> +               return -ENOSYS;
>> +       }
>> +       i2c_set_bus_num(old_i2c_bus);
>> +
>> +#ifdef CONFIG_NET_ETHADDR_EEPROM_CRC8
>> +       if (crc8(0, eeprom, ARP_HLEN) != eeprom[ARP_HLEN]) {
>> +               puts("CRC error on MAC address from EEPROM on device: ");
>> +               return -EINVAL;
>> +       }
>> +#endif
>> +#endif
>> +
>> +       memcpy(enetaddr, eeprom, ARP_HLEN);
>> +
>> +       return 0;
>> +}
>> +
>>   void eth_parse_enetaddr(const char *addr, uchar *enetaddr)
>>   {
>>          char *end;
>> diff --git a/net/eth_legacy.c b/net/eth_legacy.c
>> index bf4de37..8fb5844 100644
>> --- a/net/eth_legacy.c
>> +++ b/net/eth_legacy.c
>> @@ -136,6 +136,8 @@ int eth_write_hwaddr(struct eth_device *dev, const char *base_name,
>>          unsigned char env_enetaddr[ARP_HLEN];
>>          int ret = 0;
>>
>> +       eeprom_read_enetaddr(eth_number, dev->enetaddr);
>> +
>>          eth_getenv_enetaddr_by_index(base_name, eth_number, env_enetaddr);
>>
>>          if (!is_zero_ethaddr(env_enetaddr)) {
>> --
>> 2.10.2
>>
>> _______________________________________________
>> U-Boot mailing list
>> U-Boot at lists.denx.de
>> http://lists.denx.de/mailman/listinfo/u-boot



More information about the U-Boot mailing list