[U-Boot] [PATCH v3] usb: dwc2: add support for external vbus supply

[Marek Vasut]

On 12/03/2016 05:29 AM, Simon Glass wrote:
> From: Kever Yang <kever.yang at rock-chips.com>
> 
> Some board do not use the dwc2 internal VBUS_DRV signal, but
> use a gpio pin to enable the 5.0V VBUS power, add interface to
> enable the power in dwc2 driver.
> 
> Signed-off-by: Kever Yang <kever.yang at rock-chips.com>
> Signed-off-by: Simon Glass <sjg at chromium.org>
> ---
> 
> Changes in v3:
> - Drop use of static variable
> 
>  drivers/usb/host/dwc2.c | 39 ++++++++++++++++++++++++++++++++++-----
>  1 file changed, 34 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/usb/host/dwc2.c b/drivers/usb/host/dwc2.c
> index d08879d..fa11364 100644
> --- a/drivers/usb/host/dwc2.c
> +++ b/drivers/usb/host/dwc2.c
> @@ -15,6 +15,7 @@
>  #include <usbroothubdes.h>
>  #include <wait_bit.h>
>  #include <asm/io.h>
> +#include <power/regulator.h>
>  
>  #include "dwc2.h"
>  
> @@ -159,6 +160,28 @@ static void dwc_otg_core_reset(struct dwc2_core_regs *regs)
>  	mdelay(100);
>  }
>  
> +static int dwc_vbus_supply_init(struct udevice *dev)
> +{
> +#if defined(CONFIG_DM_USB) && defined(CONFIG_DM_REGULATOR) && \
> +	!defined(CONFIG_SPL_BUILD)
> +	struct udevice *vbus_supply;
> +	int ret;
> +
> +	ret = device_get_supply_regulator(dev, "vbus-supply", &vbus_supply);
> +	if (ret) {
> +		debug("%s: No vbus supply\n", dev->name);
> +		return 0;
> +	}
> +
> +	ret = regulator_set_enable(vbus_supply, true);
> +	if (ret) {
> +		error("Error enabling vbus supply\n");
> +		return ret;
> +	}
> +#endif
> +	return 0;
> +}
> +
>  /*
>   * This function initializes the DWC_otg controller registers for
>   * host mode.
> @@ -167,10 +190,12 @@ static void dwc_otg_core_reset(struct dwc2_core_regs *regs)
>   * request queues. Host channels are reset to ensure that they are ready for
>   * performing transfers.
>   *
> + * @param dev USB Device (NULL if driver model is not being used)
>   * @param regs Programming view of DWC_otg controller
>   *
>   */
> -static void dwc_otg_core_host_init(struct dwc2_core_regs *regs)
> +static void dwc_otg_core_host_init(struct udevice *dev,
> +				   struct dwc2_core_regs *regs)
>  {
>  	uint32_t nptxfifosize = 0;
>  	uint32_t ptxfifosize = 0;
> @@ -248,6 +273,9 @@ static void dwc_otg_core_host_init(struct dwc2_core_regs *regs)
>  			writel(hprt0, &regs->hprt0);
>  		}
>  	}
> +
> +	if (dev)
> +		dwc_vbus_supply_init(dev);
>  }
>  
>  /*
> @@ -1048,7 +1076,7 @@ int _submit_int_msg(struct dwc2_priv *priv, struct usb_device *dev,
>  	}
>  }
>  
> -static int dwc2_init_common(struct dwc2_priv *priv)
> +static int dwc2_init_common(struct udevice *dev, struct dwc2_priv *priv)
>  {
>  	struct dwc2_core_regs *regs = priv->regs;
>  	uint32_t snpsid;
> @@ -1070,7 +1098,7 @@ static int dwc2_init_common(struct dwc2_priv *priv)
>  #endif
>  
>  	dwc_otg_core_init(priv);
> -	dwc_otg_core_host_init(regs);
> +	dwc_otg_core_host_init(dev, regs);
>  
>  	clrsetbits_le32(&regs->hprt0, DWC2_HPRT0_PRTENA |
>  			DWC2_HPRT0_PRTCONNDET | DWC2_HPRT0_PRTENCHNG |
> @@ -1143,7 +1171,7 @@ int usb_lowlevel_init(int index, enum usb_init_type init, void **controller)
>  	if (board_usb_init(index, USB_INIT_HOST))
>  		return -1;
>  
> -	return dwc2_init_common(priv);
> +	return dwc2_init_common(NULL, priv);
>  }
>  
>  int usb_lowlevel_stop(int index)
> @@ -1194,6 +1222,7 @@ static int dwc2_usb_ofdata_to_platdata(struct udevice *dev)
>  	const void *prop;
>  	fdt_addr_t addr;
>  
> +	g_dwc2_udev = dev;

Needed ? :-)

>  	addr = dev_get_addr(dev);
>  	if (addr == FDT_ADDR_T_NONE)
>  		return -EINVAL;
> @@ -1214,7 +1243,7 @@ static int dwc2_usb_probe(struct udevice *dev)
>  
>  	bus_priv->desc_before_addr = true;
>  
> -	return dwc2_init_common(priv);
> +	return dwc2_init_common(dev, priv);
>  }
>  
>  static int dwc2_usb_remove(struct udevice *dev)
> 


-- 
Best regards,
Marek Vasut