[U-Boot] [PATCH v3 1/4] mmc: sdhci: Distinguish between base clock and maximum peripheral frequency
Jaehoon Chung
jh80.chung at samsung.com
Mon Dec 5 23:21:49 CET 2016
On 12/02/2016 10:24 PM, stefan.herbrechtsmeier at weidmueller.de wrote:
> From: Stefan Herbrechtsmeier <stefan.herbrechtsmeier at weidmueller.de>
>
> The sdhci controller assumes that the base clock frequency is fully supported by
> the peripheral and doesn't support hardware limitations. The Linux kernel
> distinguishes between base clock (max_clk) of the host controller and maximum
> frequency (f_max) of the card interface. Use the same differentiation and allow
> the platform to constrain the peripheral interface.
>
> Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier at weidmueller.de>
Even if this patch is delegated to Michal, i picked to this.
Applied on u-boot-mmc.
Best Regards,
Jaehoon Chung
>
> ---
>
> Changes in v3:
> - Rename arguments of sdhci_setup_cfg function from max_clk/min_clk to f_max/f_min
>
> Changes in v2: None
>
> drivers/mmc/atmel_sdhci.c | 7 +++++--
> drivers/mmc/bcm2835_sdhci.c | 3 ++-
> drivers/mmc/ftsdc021_sdhci.c | 3 ++-
> drivers/mmc/kona_sdhci.c | 3 ++-
> drivers/mmc/msm_sdhci.c | 2 ++
> drivers/mmc/mv_sdhci.c | 3 ++-
> drivers/mmc/pci_mmc.c | 1 +
> drivers/mmc/pic32_sdhci.c | 4 +++-
> drivers/mmc/rockchip_sdhci.c | 4 ++--
> drivers/mmc/s5p_sdhci.c | 5 +++--
> drivers/mmc/sdhci.c | 34 ++++++++++++++++++----------------
> drivers/mmc/spear_sdhci.c | 3 ++-
> drivers/mmc/zynq_sdhci.c | 4 +++-
> include/sdhci.h | 13 +++++++------
> 14 files changed, 54 insertions(+), 35 deletions(-)
>
> diff --git a/drivers/mmc/atmel_sdhci.c b/drivers/mmc/atmel_sdhci.c
> index 6654b54..62cb242 100644
> --- a/drivers/mmc/atmel_sdhci.c
> +++ b/drivers/mmc/atmel_sdhci.c
> @@ -35,8 +35,9 @@ int atmel_sdhci_init(void *regbase, u32 id)
> free(host);
> return -ENODEV;
> }
> + host->max_clk = max_clk;
>
> - add_sdhci(host, max_clk, min_clk);
> + add_sdhci(host, 0, min_clk);
>
> return 0;
> }
> @@ -95,7 +96,9 @@ static int atmel_sdhci_probe(struct udevice *dev)
> if (!max_clk)
> return -EINVAL;
>
> - ret = sdhci_setup_cfg(&plat->cfg, host, max_clk, ATMEL_SDHC_MIN_FREQ);
> + host->max_clk = max_clk;
> +
> + ret = sdhci_setup_cfg(&plat->cfg, host, 0, ATMEL_SDHC_MIN_FREQ);
> if (ret)
> return ret;
>
> diff --git a/drivers/mmc/bcm2835_sdhci.c b/drivers/mmc/bcm2835_sdhci.c
> index cb2bd40..29c2a85 100644
> --- a/drivers/mmc/bcm2835_sdhci.c
> +++ b/drivers/mmc/bcm2835_sdhci.c
> @@ -181,10 +181,11 @@ int bcm2835_sdhci_init(u32 regbase, u32 emmc_freq)
> host->ioaddr = (void *)(unsigned long)regbase;
> host->quirks = SDHCI_QUIRK_BROKEN_VOLTAGE | SDHCI_QUIRK_BROKEN_R1B |
> SDHCI_QUIRK_WAIT_SEND_CMD | SDHCI_QUIRK_NO_HISPD_BIT;
> + host->max_clk = emmc_freq;
> host->voltages = MMC_VDD_32_33 | MMC_VDD_33_34 | MMC_VDD_165_195;
> host->ops = &bcm2835_ops;
>
> - add_sdhci(host, emmc_freq, MIN_FREQ);
> + add_sdhci(host, 0, MIN_FREQ);
>
> return 0;
> }
> diff --git a/drivers/mmc/ftsdc021_sdhci.c b/drivers/mmc/ftsdc021_sdhci.c
> index 6e9fefa..4940ccb 100644
> --- a/drivers/mmc/ftsdc021_sdhci.c
> +++ b/drivers/mmc/ftsdc021_sdhci.c
> @@ -27,7 +27,8 @@ int ftsdc021_sdhci_init(u32 regbase)
> host->name = "FTSDC021";
> host->ioaddr = (void __iomem *)regbase;
> host->quirks = 0;
> - add_sdhci(host, freq, 0);
> + host->max_clk = freq;
> + add_sdhci(host, 0, 0);
>
> return 0;
> }
> diff --git a/drivers/mmc/kona_sdhci.c b/drivers/mmc/kona_sdhci.c
> index 549f6bc..ddd821b 100644
> --- a/drivers/mmc/kona_sdhci.c
> +++ b/drivers/mmc/kona_sdhci.c
> @@ -121,12 +121,13 @@ int kona_sdhci_init(int dev_index, u32 min_clk, u32 quirks)
> host->name = "kona-sdhci";
> host->ioaddr = reg_base;
> host->quirks = quirks;
> + host->max_clk = max_clk;
>
> if (init_kona_mmc_core(host)) {
> free(host);
> return -EINVAL;
> }
>
> - add_sdhci(host, max_clk, min_clk);
> + add_sdhci(host, 0, min_clk);
> return ret;
> }
> diff --git a/drivers/mmc/msm_sdhci.c b/drivers/mmc/msm_sdhci.c
> index f33714b..1db683d 100644
> --- a/drivers/mmc/msm_sdhci.c
> +++ b/drivers/mmc/msm_sdhci.c
> @@ -96,6 +96,8 @@ static int msm_sdc_probe(struct udevice *dev)
>
> host->quirks = SDHCI_QUIRK_WAIT_SEND_CMD | SDHCI_QUIRK_BROKEN_R1B;
>
> + host->max_clk = 0;
> +
> /* Init clocks */
> ret = msm_sdc_clk_init(dev);
> if (ret)
> diff --git a/drivers/mmc/mv_sdhci.c b/drivers/mmc/mv_sdhci.c
> index e388ad1..69aa87b 100644
> --- a/drivers/mmc/mv_sdhci.c
> +++ b/drivers/mmc/mv_sdhci.c
> @@ -77,6 +77,7 @@ int mv_sdh_init(unsigned long regbase, u32 max_clk, u32 min_clk, u32 quirks)
> host->name = MVSDH_NAME;
> host->ioaddr = (void *)regbase;
> host->quirks = quirks;
> + host->max_clk = max_clk;
> #ifdef CONFIG_MMC_SDHCI_IO_ACCESSORS
> memset(&mv_ops, 0, sizeof(struct sdhci_ops));
> mv_ops.write_b = mv_sdhci_writeb;
> @@ -88,5 +89,5 @@ int mv_sdh_init(unsigned long regbase, u32 max_clk, u32 min_clk, u32 quirks)
> sdhci_mvebu_mbus_config((void __iomem *)regbase);
> }
>
> - return add_sdhci(host, max_clk, min_clk);
> + return add_sdhci(host, 0, min_clk);
> }
> diff --git a/drivers/mmc/pci_mmc.c b/drivers/mmc/pci_mmc.c
> index 3d587cc..e39b476 100644
> --- a/drivers/mmc/pci_mmc.c
> +++ b/drivers/mmc/pci_mmc.c
> @@ -32,6 +32,7 @@ int pci_mmc_init(const char *name, struct pci_device_id *mmc_supported)
> dm_pci_read_config32(dev, PCI_BASE_ADDRESS_0, &iobase);
> mmc_host->ioaddr = (void *)(ulong)iobase;
> mmc_host->quirks = 0;
> + mmc_host->max_clk = 0;
> ret = add_sdhci(mmc_host, 0, 0);
> if (ret)
> return ret;
> diff --git a/drivers/mmc/pic32_sdhci.c b/drivers/mmc/pic32_sdhci.c
> index 2abf943..c562aec 100644
> --- a/drivers/mmc/pic32_sdhci.c
> +++ b/drivers/mmc/pic32_sdhci.c
> @@ -41,7 +41,9 @@ static int pic32_sdhci_probe(struct udevice *dev)
> return ret;
> }
>
> - ret = add_sdhci(host, f_min_max[1], f_min_max[0]);
> + host->max_clk = f_min_max[1];
> +
> + ret = add_sdhci(host, 0, f_min_max[0]);
> if (ret)
> return ret;
> host->mmc->dev = dev;
> diff --git a/drivers/mmc/rockchip_sdhci.c b/drivers/mmc/rockchip_sdhci.c
> index c56e1a3..4456a02 100644
> --- a/drivers/mmc/rockchip_sdhci.c
> +++ b/drivers/mmc/rockchip_sdhci.c
> @@ -35,9 +35,9 @@ static int arasan_sdhci_probe(struct udevice *dev)
> int ret;
>
> host->quirks = SDHCI_QUIRK_WAIT_SEND_CMD;
> + host->max_clk = CONFIG_ROCKCHIP_SDHCI_MAX_FREQ;
>
> - ret = sdhci_setup_cfg(&plat->cfg, host, CONFIG_ROCKCHIP_SDHCI_MAX_FREQ,
> - EMMC_MIN_FREQ);
> + ret = sdhci_setup_cfg(&plat->cfg, host, 0, EMMC_MIN_FREQ);
>
> host->mmc = &plat->mmc;
> if (ret)
> diff --git a/drivers/mmc/s5p_sdhci.c b/drivers/mmc/s5p_sdhci.c
> index ac737e0..bf0c485 100644
> --- a/drivers/mmc/s5p_sdhci.c
> +++ b/drivers/mmc/s5p_sdhci.c
> @@ -80,6 +80,7 @@ static int s5p_sdhci_core_init(struct sdhci_host *host)
> host->quirks = SDHCI_QUIRK_NO_HISPD_BIT | SDHCI_QUIRK_BROKEN_VOLTAGE |
> SDHCI_QUIRK_32BIT_DMA_ADDR |
> SDHCI_QUIRK_WAIT_SEND_CMD | SDHCI_QUIRK_USE_WIDE8;
> + host->max_clk = 52000000;
> host->voltages = MMC_VDD_32_33 | MMC_VDD_33_34 | MMC_VDD_165_195;
>
> host->set_control_reg = &s5p_sdhci_set_control_reg;
> @@ -89,7 +90,7 @@ static int s5p_sdhci_core_init(struct sdhci_host *host)
> host->host_caps |= MMC_MODE_8BIT;
>
> #ifndef CONFIG_BLK
> - return add_sdhci(host, 52000000, 400000);
> + return add_sdhci(host, 0, 400000);
> #else
> return 0;
> #endif
> @@ -245,7 +246,7 @@ static int s5p_sdhci_probe(struct udevice *dev)
> if (ret)
> return ret;
>
> - ret = sdhci_setup_cfg(&plat->cfg, host, 52000000, 400000);
> + ret = sdhci_setup_cfg(&plat->cfg, host, 0, 400000);
> if (ret)
> return ret;
>
> diff --git a/drivers/mmc/sdhci.c b/drivers/mmc/sdhci.c
> index 766e9ee..0e59dbc 100644
> --- a/drivers/mmc/sdhci.c
> +++ b/drivers/mmc/sdhci.c
> @@ -325,7 +325,7 @@ static int sdhci_set_clock(struct mmc *mmc, unsigned int clock)
> */
> if (host->clk_mul) {
> for (div = 1; div <= 1024; div++) {
> - if ((mmc->cfg->f_max * host->clk_mul / div)
> + if ((host->max_clk * host->clk_mul / div)
> <= clock)
> break;
> }
> @@ -338,13 +338,13 @@ static int sdhci_set_clock(struct mmc *mmc, unsigned int clock)
> div--;
> } else {
> /* Version 3.00 divisors must be a multiple of 2. */
> - if (mmc->cfg->f_max <= clock) {
> + if (host->max_clk <= clock) {
> div = 1;
> } else {
> for (div = 2;
> div < SDHCI_MAX_DIV_SPEC_300;
> div += 2) {
> - if ((mmc->cfg->f_max / div) <= clock)
> + if ((host->max_clk / div) <= clock)
> break;
> }
> }
> @@ -353,7 +353,7 @@ static int sdhci_set_clock(struct mmc *mmc, unsigned int clock)
> } else {
> /* Version 2.00 divisors must be a power of 2. */
> for (div = 1; div < SDHCI_MAX_DIV_SPEC_200; div *= 2) {
> - if ((mmc->cfg->f_max / div) <= clock)
> + if ((host->max_clk / div) <= clock)
> break;
> }
> div >>= 1;
> @@ -534,7 +534,7 @@ static const struct mmc_ops sdhci_ops = {
> #endif
>
> int sdhci_setup_cfg(struct mmc_config *cfg, struct sdhci_host *host,
> - u32 max_clk, u32 min_clk)
> + u32 f_max, u32 f_min)
> {
> u32 caps, caps_1;
>
> @@ -557,24 +557,26 @@ int sdhci_setup_cfg(struct mmc_config *cfg, struct sdhci_host *host,
> #ifndef CONFIG_DM_MMC_OPS
> cfg->ops = &sdhci_ops;
> #endif
> - if (max_clk)
> - cfg->f_max = max_clk;
> - else {
> + if (host->max_clk == 0) {
> if (SDHCI_GET_VERSION(host) >= SDHCI_SPEC_300)
> - cfg->f_max = (caps & SDHCI_CLOCK_V3_BASE_MASK) >>
> + host->max_clk = (caps & SDHCI_CLOCK_V3_BASE_MASK) >>
> SDHCI_CLOCK_BASE_SHIFT;
> else
> - cfg->f_max = (caps & SDHCI_CLOCK_BASE_MASK) >>
> + host->max_clk = (caps & SDHCI_CLOCK_BASE_MASK) >>
> SDHCI_CLOCK_BASE_SHIFT;
> - cfg->f_max *= 1000000;
> + host->max_clk *= 1000000;
> }
> - if (cfg->f_max == 0) {
> + if (host->max_clk == 0) {
> printf("%s: Hardware doesn't specify base clock frequency\n",
> __func__);
> return -EINVAL;
> }
> - if (min_clk)
> - cfg->f_min = min_clk;
> + if (f_max && (f_max < host->max_clk))
> + cfg->f_max = f_max;
> + else
> + cfg->f_max = host->max_clk;
> + if (f_min)
> + cfg->f_min = f_min;
> else {
> if (SDHCI_GET_VERSION(host) >= SDHCI_SPEC_300)
> cfg->f_min = cfg->f_max / SDHCI_MAX_DIV_SPEC_300;
> @@ -623,11 +625,11 @@ int sdhci_bind(struct udevice *dev, struct mmc *mmc, struct mmc_config *cfg)
> return mmc_bind(dev, mmc, cfg);
> }
> #else
> -int add_sdhci(struct sdhci_host *host, u32 max_clk, u32 min_clk)
> +int add_sdhci(struct sdhci_host *host, u32 f_max, u32 f_min)
> {
> int ret;
>
> - ret = sdhci_setup_cfg(&host->cfg, host, max_clk, min_clk);
> + ret = sdhci_setup_cfg(&host->cfg, host, f_max, f_min);
> if (ret)
> return ret;
>
> diff --git a/drivers/mmc/spear_sdhci.c b/drivers/mmc/spear_sdhci.c
> index 06179cd..d3f8669 100644
> --- a/drivers/mmc/spear_sdhci.c
> +++ b/drivers/mmc/spear_sdhci.c
> @@ -21,7 +21,8 @@ int spear_sdhci_init(u32 regbase, u32 max_clk, u32 min_clk, u32 quirks)
> host->name = "sdhci";
> host->ioaddr = (void *)regbase;
> host->quirks = quirks;
> + host->max_clk = max_clk;
>
> - add_sdhci(host, max_clk, min_clk);
> + add_sdhci(host, 0, min_clk);
> return 0;
> }
> diff --git a/drivers/mmc/zynq_sdhci.c b/drivers/mmc/zynq_sdhci.c
> index 3da1385..69efa38 100644
> --- a/drivers/mmc/zynq_sdhci.c
> +++ b/drivers/mmc/zynq_sdhci.c
> @@ -36,7 +36,9 @@ static int arasan_sdhci_probe(struct udevice *dev)
> host->quirks |= SDHCI_QUIRK_NO_HISPD_BIT;
> #endif
>
> - ret = sdhci_setup_cfg(&plat->cfg, host, CONFIG_ZYNQ_SDHCI_MAX_FREQ,
> + host->max_clk = CONFIG_ZYNQ_SDHCI_MAX_FREQ;
> +
> + ret = sdhci_setup_cfg(&plat->cfg, host, 0,
> CONFIG_ZYNQ_SDHCI_MIN_FREQ);
> host->mmc = &plat->mmc;
> if (ret)
> diff --git a/include/sdhci.h b/include/sdhci.h
> index 144570f..6c9f7a7 100644
> --- a/include/sdhci.h
> +++ b/include/sdhci.h
> @@ -243,6 +243,7 @@ struct sdhci_host {
> unsigned int quirks;
> unsigned int host_caps;
> unsigned int version;
> + unsigned int max_clk; /* Maximum Base Clock frequency */
> unsigned int clk_mul; /* Clock Multiplier value */
> unsigned int clock;
> struct mmc *mmc;
> @@ -372,11 +373,11 @@ static inline u8 sdhci_readb(struct sdhci_host *host, int reg)
> *
> * @cfg: Configuration structure to fill in (generally &plat->mmc)
> * @host: SDHCI host structure
> - * @max_clk: Maximum supported clock speed in HZ (0 for default)
> - * @min_clk: Minimum supported clock speed in HZ (0 for default)
> + * @f_max: Maximum supported clock frequency in HZ (0 for default)
> + * @f_min: Minimum supported clock frequency in HZ (0 for default)
> */
> int sdhci_setup_cfg(struct mmc_config *cfg, struct sdhci_host *host,
> - u32 max_clk, u32 min_clk);
> + u32 f_max, u32 f_min);
>
> /**
> * sdhci_bind() - Set up a new MMC block device
> @@ -402,11 +403,11 @@ int sdhci_bind(struct udevice *dev, struct mmc *mmc, struct mmc_config *cfg);
> * This is used when you are not using CONFIG_BLK. Convert your driver over!
> *
> * @host: SDHCI host structure
> - * @max_clk: Maximum supported clock speed in HZ (0 for default)
> - * @min_clk: Minimum supported clock speed in HZ (0 for default)
> + * @f_max: Maximum supported clock frequency in HZ (0 for default)
> + * @f_min: Minimum supported clock frequency in HZ (0 for default)
> * @return 0 if OK, -ve on error
> */
> -int add_sdhci(struct sdhci_host *host, u32 max_clk, u32 min_clk);
> +int add_sdhci(struct sdhci_host *host, u32 f_max, u32 f_min);
> #endif /* !CONFIG_BLK */
>
> #ifdef CONFIG_DM_MMC_OPS
>
More information about the U-Boot
mailing list