[U-Boot] [PATCH 03/11] net: e1000: Convert to use DM PCI API
Bin Meng
bmeng.cn at gmail.com
Tue Feb 2 14:58:01 CET 2016
Update this driver to use proper DM PCI APIs.
Signed-off-by: Bin Meng <bmeng.cn at gmail.com>
---
drivers/net/e1000.c | 75 ++++++++++++++++++++++++++++++++++++++++++++++++++++-
drivers/net/e1000.h | 4 +++
2 files changed, 78 insertions(+), 1 deletion(-)
diff --git a/drivers/net/e1000.c b/drivers/net/e1000.c
index 70fc02e..2f2185d 100644
--- a/drivers/net/e1000.c
+++ b/drivers/net/e1000.c
@@ -38,8 +38,13 @@ tested on both gig copper and gig fiber boards
#define TOUT_LOOP 100000
+#ifdef CONFIG_DM_ETH
+#define virt_to_bus(devno, v) dm_pci_virt_to_mem(devno, (void *) (v))
+#define bus_to_phys(devno, a) dm_pci_mem_to_phys(devno, a)
+#else
#define virt_to_bus(devno, v) pci_virt_to_mem(devno, (void *) (v))
#define bus_to_phys(devno, a) pci_mem_to_phys(devno, a)
+#endif
#define E1000_DEFAULT_PCI_PBA 0x00000030
#define E1000_DEFAULT_PCIE_PBA 0x000a0026
@@ -1395,8 +1400,13 @@ e1000_reset_hw(struct e1000_hw *hw)
/* For 82542 (rev 2.0), disable MWI before issuing a device reset */
if (hw->mac_type == e1000_82542_rev2_0) {
DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
+#ifdef CONFIG_DM_ETH
+ dm_pci_write_config16(hw->pdev, PCI_COMMAND,
+ hw->pci_cmd_word & ~PCI_COMMAND_INVALIDATE);
+#else
pci_write_config_word(hw->pdev, PCI_COMMAND,
hw->pci_cmd_word & ~PCI_COMMAND_INVALIDATE);
+#endif
}
/* Clear interrupt mask to stop board from generating interrupts */
@@ -1469,7 +1479,11 @@ e1000_reset_hw(struct e1000_hw *hw)
/* If MWI was previously enabled, reenable it. */
if (hw->mac_type == e1000_82542_rev2_0) {
+#ifdef CONFIG_DM_ETH
+ dm_pci_write_config16(hw->pdev, PCI_COMMAND, hw->pci_cmd_word);
+#else
pci_write_config_word(hw->pdev, PCI_COMMAND, hw->pci_cmd_word);
+#endif
}
if (hw->mac_type != e1000_igb)
E1000_WRITE_REG(hw, PBA, pba);
@@ -1655,9 +1669,15 @@ e1000_init_hw(struct e1000_hw *hw, unsigned char enetaddr[6])
/* For 82542 (rev 2.0), disable MWI and put the receiver into reset */
if (hw->mac_type == e1000_82542_rev2_0) {
DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
+#ifdef CONFIG_DM_ETH
+ dm_pci_write_config16(hw->pdev, PCI_COMMAND,
+ hw->
+ pci_cmd_word & ~PCI_COMMAND_INVALIDATE);
+#else
pci_write_config_word(hw->pdev, PCI_COMMAND,
hw->
pci_cmd_word & ~PCI_COMMAND_INVALIDATE);
+#endif
E1000_WRITE_REG(hw, RCTL, E1000_RCTL_RST);
E1000_WRITE_FLUSH(hw);
mdelay(5);
@@ -1673,7 +1693,11 @@ e1000_init_hw(struct e1000_hw *hw, unsigned char enetaddr[6])
E1000_WRITE_REG(hw, RCTL, 0);
E1000_WRITE_FLUSH(hw);
mdelay(1);
+#ifdef CONFIG_DM_ETH
+ dm_pci_write_config16(hw->pdev, PCI_COMMAND, hw->pci_cmd_word);
+#else
pci_write_config_word(hw->pdev, PCI_COMMAND, hw->pci_cmd_word);
+#endif
}
/* Zero out the Multicast HASH table */
@@ -1696,10 +1720,17 @@ e1000_init_hw(struct e1000_hw *hw, unsigned char enetaddr[6])
default:
/* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */
if (hw->bus_type == e1000_bus_type_pcix) {
+#ifdef CONFIG_DM_ETH
+ dm_pci_read_config16(hw->pdev, PCIX_COMMAND_REGISTER,
+ &pcix_cmd_word);
+ dm_pci_read_config16(hw->pdev, PCIX_STATUS_REGISTER_HI,
+ &pcix_stat_hi_word);
+#else
pci_read_config_word(hw->pdev, PCIX_COMMAND_REGISTER,
&pcix_cmd_word);
pci_read_config_word(hw->pdev, PCIX_STATUS_REGISTER_HI,
&pcix_stat_hi_word);
+#endif
cmd_mmrbc =
(pcix_cmd_word & PCIX_COMMAND_MMRBC_MASK) >>
PCIX_COMMAND_MMRBC_SHIFT;
@@ -1711,8 +1742,13 @@ e1000_init_hw(struct e1000_hw *hw, unsigned char enetaddr[6])
if (cmd_mmrbc > stat_mmrbc) {
pcix_cmd_word &= ~PCIX_COMMAND_MMRBC_MASK;
pcix_cmd_word |= stat_mmrbc << PCIX_COMMAND_MMRBC_SHIFT;
+#ifdef CONFIG_DM_ETH
+ dm_pci_write_config16(hw->pdev, PCIX_COMMAND_REGISTER,
+ pcix_cmd_word);
+#else
pci_write_config_word(hw->pdev, PCIX_COMMAND_REGISTER,
pcix_cmd_word);
+#endif
}
}
break;
@@ -4809,6 +4845,16 @@ e1000_sw_init(struct e1000_hw *hw)
int result;
/* PCI config space info */
+#ifdef CONFIG_DM_ETH
+ dm_pci_read_config16(hw->pdev, PCI_VENDOR_ID, &hw->vendor_id);
+ dm_pci_read_config16(hw->pdev, PCI_DEVICE_ID, &hw->device_id);
+ dm_pci_read_config16(hw->pdev, PCI_SUBSYSTEM_VENDOR_ID,
+ &hw->subsystem_vendor_id);
+ dm_pci_read_config16(hw->pdev, PCI_SUBSYSTEM_ID, &hw->subsystem_id);
+
+ dm_pci_read_config8(hw->pdev, PCI_REVISION_ID, &hw->revision_id);
+ dm_pci_read_config16(hw->pdev, PCI_COMMAND, &hw->pci_cmd_word);
+#else
pci_read_config_word(hw->pdev, PCI_VENDOR_ID, &hw->vendor_id);
pci_read_config_word(hw->pdev, PCI_DEVICE_ID, &hw->device_id);
pci_read_config_word(hw->pdev, PCI_SUBSYSTEM_VENDOR_ID,
@@ -4817,6 +4863,7 @@ e1000_sw_init(struct e1000_hw *hw)
pci_read_config_byte(hw->pdev, PCI_REVISION_ID, &hw->revision_id);
pci_read_config_word(hw->pdev, PCI_COMMAND, &hw->pci_cmd_word);
+#endif
/* identify the MAC */
result = e1000_set_mac_type(hw);
@@ -5232,25 +5279,46 @@ void e1000_get_bus_type(struct e1000_hw *hw)
static LIST_HEAD(e1000_hw_list);
#endif
+#ifdef CONFIG_DM_ETH
+static int e1000_init_one(struct e1000_hw *hw, int cardnum,
+ struct udevice *devno, unsigned char enetaddr[6])
+#else
static int e1000_init_one(struct e1000_hw *hw, int cardnum, pci_dev_t devno,
unsigned char enetaddr[6])
+#endif
{
u32 val;
/* Assign the passed-in values */
+#ifdef CONFIG_DM_ETH
hw->pdev = devno;
+#else
+ hw->pdev = devno;
+#endif
hw->cardnum = cardnum;
/* Print a debug message with the IO base address */
+#ifdef CONFIG_DM_ETH
+ dm_pci_read_config32(devno, PCI_BASE_ADDRESS_0, &val);
+#else
pci_read_config_dword(devno, PCI_BASE_ADDRESS_0, &val);
+#endif
E1000_DBG(hw, "iobase 0x%08x\n", val & 0xfffffff0);
/* Try to enable I/O accesses and bus-mastering */
val = PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER;
+#ifdef CONFIG_DM_ETH
+ dm_pci_write_config32(devno, PCI_COMMAND, val);
+#else
pci_write_config_dword(devno, PCI_COMMAND, val);
+#endif
/* Make sure it worked */
+#ifdef CONFIG_DM_ETH
+ dm_pci_read_config32(devno, PCI_COMMAND, &val);
+#else
pci_read_config_dword(devno, PCI_COMMAND, &val);
+#endif
if (!(val & PCI_COMMAND_MEMORY)) {
E1000_ERR(hw, "Can't enable I/O memory\n");
return -ENOSPC;
@@ -5269,8 +5337,13 @@ static int e1000_init_one(struct e1000_hw *hw, int cardnum, pci_dev_t devno,
#ifndef CONFIG_E1000_NO_NVM
hw->eeprom_semaphore_present = true;
#endif
+#ifdef CONFIG_DM_ETH
+ hw->hw_addr = dm_pci_map_bar(devno, PCI_BASE_ADDRESS_0,
+ PCI_REGION_MEM);
+#else
hw->hw_addr = pci_map_bar(devno, PCI_BASE_ADDRESS_0,
PCI_REGION_MEM);
+#endif
hw->mac_type = e1000_undefined;
/* MAC and Phy settings */
@@ -5554,7 +5627,7 @@ static int e1000_eth_probe(struct udevice *dev)
hw->name = dev->name;
ret = e1000_init_one(hw, trailing_strtol(dev->name),
- dm_pci_get_bdf(dev), plat->enetaddr);
+ dev, plat->enetaddr);
if (ret < 0) {
printf(pr_fmt("failed to initialize card: %d\n"), ret);
return ret;
diff --git a/drivers/net/e1000.h b/drivers/net/e1000.h
index e46edcd..fcb7df0 100644
--- a/drivers/net/e1000.h
+++ b/drivers/net/e1000.h
@@ -1084,7 +1084,11 @@ struct e1000_hw {
#endif
unsigned int cardnum;
+#ifdef CONFIG_DM_ETH
+ struct udevice *pdev;
+#else
pci_dev_t pdev;
+#endif
uint8_t *hw_addr;
e1000_mac_type mac_type;
e1000_phy_type phy_type;
--
1.8.2.1
More information about the U-Boot
mailing list