[U-Boot] [PATCH v2 2/5] superio: Add SMSC SIO1007 driver
Bin Meng
bmeng.cn at gmail.com
Sat Feb 6 07:08:37 CET 2016
The SMSC SIO1007 superio chipset integrates two ns16550 compatible
serial ports for legacy applications, 16 GPIO pins and some other
functionalities like power management.
This adds a simple driver to enable serial port and handle GPIO.
Signed-off-by: Bin Meng <bmeng.cn at gmail.com>
---
Changes in v2: None
drivers/misc/Makefile | 1 +
drivers/misc/smsc_sio1007.c | 126 ++++++++++++++++++++++++++++++++++++++++++++
include/smsc_sio1007.h | 115 ++++++++++++++++++++++++++++++++++++++++
3 files changed, 242 insertions(+)
create mode 100644 drivers/misc/smsc_sio1007.c
create mode 100644 include/smsc_sio1007.h
diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
index e1e3c6b..f2b08ab 100644
--- a/drivers/misc/Makefile
+++ b/drivers/misc/Makefile
@@ -32,6 +32,7 @@ ifdef CONFIG_DM_I2C
obj-$(CONFIG_SANDBOX) += i2c_eeprom_emul.o
endif
obj-$(CONFIG_SMSC_LPC47M) += smsc_lpc47m.o
+obj-$(CONFIG_SMSC_SIO1007) += smsc_sio1007.o
obj-$(CONFIG_STATUS_LED) += status_led.o
obj-$(CONFIG_SANDBOX) += swap_case.o
obj-$(CONFIG_SANDBOX) += syscon_sandbox.o
diff --git a/drivers/misc/smsc_sio1007.c b/drivers/misc/smsc_sio1007.c
new file mode 100644
index 0000000..ec53533
--- /dev/null
+++ b/drivers/misc/smsc_sio1007.c
@@ -0,0 +1,126 @@
+/*
+ * Copyright (C) 2016, Bin Meng <bmeng.cn at gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <errno.h>
+#include <smsc_sio1007.h>
+
+static inline u8 sio1007_read(int port, int reg)
+{
+ outb(reg, port);
+
+ return inb(port + 1);
+}
+
+static inline void sio1007_write(int port, int reg, int val)
+{
+ outb(reg, port);
+ outb(val, port + 1);
+}
+
+static inline void sio1007_clrsetbits(int port, int reg, u8 clr, u8 set)
+{
+ sio1007_write(port, reg, (sio1007_read(port, reg) & ~clr) | set);
+}
+
+void sio1007_enable_serial(int port, int num, int iobase, int irq)
+{
+ if (num < 0 || num > SIO1007_UART_NUM)
+ return;
+
+ /* enter configuration state */
+ outb(0x55, port);
+
+ /* power on serial port and set up its i/o base & irq */
+ if (!num) {
+ sio1007_clrsetbits(port, DEV_POWER_CTRL, 0, UART1_POWER_ON);
+ sio1007_clrsetbits(port, UART1_IOBASE, 0xfe, iobase >> 2);
+ sio1007_clrsetbits(port, UART_IRQ, 0xf0, irq << 4);
+ } else {
+ sio1007_clrsetbits(port, DEV_POWER_CTRL, 0, UART2_POWER_ON);
+ sio1007_clrsetbits(port, UART2_IOBASE, 0xfe, iobase >> 2);
+ sio1007_clrsetbits(port, UART_IRQ, 0x0f, irq);
+ }
+
+ /* exit configuration state */
+ outb(0xaa, port);
+}
+
+void sio1007_enable_runtime(int port, int iobase)
+{
+ /* enter configuration state */
+ outb(0x55, port);
+
+ /* set i/o base for the runtime register block */
+ sio1007_clrsetbits(port, RTR_IOBASE_LOW, 0, iobase >> 4);
+ sio1007_clrsetbits(port, RTR_IOBASE_HIGH, 0, iobase >> 12);
+ /* turn on address decoding for this block */
+ sio1007_clrsetbits(port, DEV_ACTIVATE, 0, RTR_EN);
+
+ /* exit configuration state */
+ outb(0xaa, port);
+}
+
+void sio1007_gpio_config(int port, int gpio, int dir, int pol, int type)
+{
+ int reg = GPIO0_DIR;
+
+ if (gpio < 0 || gpio > SIO1007_GPIO_NUM)
+ return;
+ if (gpio >= GPIO_NUM_PER_GROUP) {
+ reg = GPIO1_DIR;
+ gpio -= GPIO_NUM_PER_GROUP;
+ }
+
+ /* enter configuration state */
+ outb(0x55, port);
+
+ /* set gpio pin direction, polority and type */
+ sio1007_clrsetbits(port, reg, 1 << gpio, dir << gpio);
+ sio1007_clrsetbits(port, reg + 1, 1 << gpio, pol << gpio);
+ sio1007_clrsetbits(port, reg + 2, 1 << gpio, type << gpio);
+
+ /* exit configuration state */
+ outb(0xaa, port);
+}
+
+int sio1007_gpio_get_value(int port, int gpio)
+{
+ int reg = GPIO0_DATA;
+ int val;
+
+ if (gpio < 0 || gpio > SIO1007_GPIO_NUM)
+ return -EINVAL;
+ if (gpio >= GPIO_NUM_PER_GROUP) {
+ reg = GPIO1_DATA;
+ gpio -= GPIO_NUM_PER_GROUP;
+ }
+
+ val = inb(port + reg);
+ if (val & (1 << gpio))
+ return 1;
+ else
+ return 0;
+}
+
+void sio1007_gpio_set_value(int port, int gpio, int val)
+{
+ int reg = GPIO0_DATA;
+ u8 data;
+
+ if (gpio < 0 || gpio > SIO1007_GPIO_NUM)
+ return;
+ if (gpio >= GPIO_NUM_PER_GROUP) {
+ reg = GPIO1_DATA;
+ gpio -= GPIO_NUM_PER_GROUP;
+ }
+
+ data = inb(port + reg);
+ data &= ~(1 << gpio);
+ data |= (val << gpio);
+ outb(data, port + reg);
+}
diff --git a/include/smsc_sio1007.h b/include/smsc_sio1007.h
new file mode 100644
index 0000000..805fa0e
--- /dev/null
+++ b/include/smsc_sio1007.h
@@ -0,0 +1,115 @@
+/*
+ * Copyright (C) 2016, Bin Meng <bmeng.cn at gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _SMSC_SIO1007_H_
+#define _SMSC_SIO1007_H_
+
+/*
+ * The I/O base address of SIO1007 at power-up is determined by the SYSOPT0
+ * and SYSOPT1 pins at the deasserting edge of PCIRST#. The combination of
+ * SYSOPT0 and SYSOPT1 determines one of the following addresses.
+ */
+#define SIO1007_IOPORT0 0x002e
+#define SIO1007_IOPORT1 0x004e
+#define SIO1007_IOPORT2 0x162e
+#define SIO1007_IOPORT3 0x164e
+
+/* SIO1007 registers */
+
+#define DEV_POWER_CTRL 0x02
+#define UART1_POWER_ON (1 << 3)
+#define UART2_POWER_ON (1 << 7)
+
+#define UART1_IOBASE 0x24
+#define UART2_IOBASE 0x25
+#define UART_IRQ 0x28
+
+#define RTR_IOBASE_HIGH 0x21
+#define RTR_IOBASE_LOW 0x30
+
+#define GPIO0_DIR 0x31
+#define GPIO1_DIR 0x35
+#define GPIO_DIR_INPUT 0
+#define GPIO_DIR_OUTPUT 1
+
+#define GPIO0_POL 0x32
+#define GPIO1_POL 0x36
+#define GPIO_POL_NO_INVERT 0
+#define GPIO_POL_INVERT 1
+
+#define GPIO0_TYPE 0x33
+#define GPIO1_TYPE 0x37
+#define GPIO_TYPE_PUSH_PULL 0
+#define GPIO_TYPE_OPEN_DRAIN 1
+
+#define DEV_ACTIVATE 0x3a
+#define RTR_EN (1 << 1)
+
+/* Runtime register offset */
+
+#define GPIO0_DATA 0xc
+#define GPIO1_DATA 0xe
+
+/* Number of serial ports supported */
+#define SIO1007_UART_NUM 2
+
+/* Number of gpio pins supported */
+#define GPIO_NUM_PER_GROUP 8
+#define GPIO_GROUP_NUM 2
+#define SIO1007_GPIO_NUM (GPIO_NUM_PER_GROUP * GPIO_GROUP_NUM)
+
+/**
+ * Configure the I/O port address of the specified serial device and
+ * enable the serial device.
+ *
+ * @port: SIO1007 I/O port address
+ * @num: serial device number (0 or 1)
+ * @iobase: processor I/O port address to assign to this serial device
+ * @irq: processor IRQ number to assign to this serial device
+ */
+void sio1007_enable_serial(int port, int num, int iobase, int irq);
+
+/**
+ * Configure the I/O port address of the runtime register block and
+ * enable the address decoding.
+ *
+ * @port: SIO1007 I/O port address
+ * @iobase: processor I/O port address to assign to the runtime registers
+ */
+void sio1007_enable_runtime(int port, int iobase);
+
+/**
+ * Configure the direction/polority/type of a specified GPIO pin
+ *
+ * @port: SIO1007 I/O port address
+ * @gpio: GPIO number (0-7 for GP10-GP17, 8-15 for GP30-GP37)
+ * @dir: GPIO_DIR_INPUT or GPIO_DIR_OUTPUT
+ * @pol: GPIO_POL_NO_INVERT or GPIO_POL_INVERT
+ * @type: GPIO_TYPE_PUSH_PULL or GPIO_TYPE_OPEN_DRAIN
+ */
+void sio1007_gpio_config(int port, int gpio, int dir, int pol, int type);
+
+/**
+ * Get a GPIO pin value.
+ * This will work whether the GPIO is an input or an output.
+ *
+ * @port: runtime register block I/O port address
+ * @gpio: GPIO number (0-7 for GP10-GP17, 8-15 for GP30-GP37)
+ * @return: 0 if low, 1 if high, -EINVAL if gpio number is invalid
+ */
+int sio1007_gpio_get_value(int port, int gpio);
+
+/**
+ * Set a GPIO pin value.
+ * This will only work when the GPIO is configured as an output.
+ *
+ * @port: runtime register block I/O port address
+ * @gpio: GPIO number (0-7 for GP10-GP17, 8-15 for GP30-GP37)
+ * @val: 0 if low, 1 if high
+ */
+void sio1007_gpio_set_value(int port, int gpio, int val);
+
+#endif /* _SMSC_SIO1007_H_ */
--
1.8.2.1
More information about the U-Boot
mailing list