[U-Boot] [PATCH v2 15/18] gpio: Add support for Qualcomm PM8916 gpios
Mateusz Kulikowski
mateusz.kulikowski at gmail.com
Sun Feb 7 21:57:35 CET 2016
This driver supports GPIOs present on PM8916 PMIC.
There are 2 device drivers inside:
- GPIO driver (4 "generic" GPIOs)
- Keypad driver that presents itself as GPIO with 2 inputs (power and reset)
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski at gmail.com>
Reviewed-by: Simon Glass <sjg at chromium.org>
Tested-by: Simon Glass <sjg at chromium.org>
---
Changes in v3: None
Changes in v2:
- Add Reviewed-by
Changes in v1:
- Add binding doc
- Fixed inlcude ordering
- Merged direction_input and direction_output functions
- gpio_get: use switch instead of stacked if
- use pmic_clrsetbits
- add possibility to change prwkey bank name
- Handle invalid bindings
- Sanity HW check (i.e. check type/subtype registers)
doc/device-tree-bindings/gpio/pm8916_gpio.txt | 48 ++++
drivers/gpio/Kconfig | 10 +
drivers/gpio/Makefile | 1 +
drivers/gpio/pm8916_gpio.c | 302 ++++++++++++++++++++++++++
4 files changed, 361 insertions(+)
create mode 100644 doc/device-tree-bindings/gpio/pm8916_gpio.txt
create mode 100644 drivers/gpio/pm8916_gpio.c
diff --git a/doc/device-tree-bindings/gpio/pm8916_gpio.txt b/doc/device-tree-bindings/gpio/pm8916_gpio.txt
new file mode 100644
index 0000000..58185b8
--- /dev/null
+++ b/doc/device-tree-bindings/gpio/pm8916_gpio.txt
@@ -0,0 +1,48 @@
+Driver for part of pm8916 PMIC - gpio and power/reset keys
+
+This device should be child of SPMI pmic.
+
+1) GPIO driver
+
+Required properties:
+- compatible: "qcom,pm8916-gpio"
+- reg: peripheral ID, size of register block
+- gpio-controller
+- gpio-count: number of GPIOs
+- #gpio-cells: 2
+
+Optional properties:
+- gpio-bank-name: name of bank (as default "pm8916" is used)
+
+Example:
+
+pmic_gpios: gpios at c000 {
+ compatible = "qcom,pm8916-gpio";
+ reg = <0xc000 0x400>;
+ gpio-controller;
+ gpio-count = <4>;
+ #gpio-cells = <2>;
+ gpio-bank-name="pmic";
+};
+
+
+2) Power/Reset key driver
+
+Required properties:
+- compatible: "qcom,pm8916-pwrkey"
+- reg: peripheral ID, size of register block
+- gpio-controller
+- #gpio-cells: 2
+
+Optional properties:
+- gpio-bank-name: name of bank (as default "pm8916_key" is used)
+
+
+Example:
+
+pmic_pon: pon at 800 {
+ compatible = "qcom,pm8916-pwrkey";
+ reg = <0x800 0x96>;
+ #gpio-cells = <2>;
+ gpio-controller;
+};
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index a5e8182..bbafc63 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -60,6 +60,16 @@ config MSM_GPIO
- APQ8016
- MSM8916
+config PM8916_GPIO
+ bool "Qualcomm PM8916 PMIC GPIO/keypad driver"
+ depends on DM_GPIO && PMIC_PM8916
+ help
+ Support for GPIO pins and power/reset buttons found on
+ Qualcomm PM8916 PMIC.
+ Default name for GPIO bank is "pm8916".
+ Power and reset buttons are placed in "pm8916_key" bank and
+ have gpio numbers 0 and 1 respectively.
+
config ROCKCHIP_GPIO
bool "Rockchip GPIO driver"
depends on DM_GPIO
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 6083c4a..8e880bd 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -48,3 +48,4 @@ obj-$(CONFIG_VYBRID_GPIO) += vybrid_gpio.o
obj-$(CONFIG_HIKEY_GPIO) += hi6220_gpio.o
obj-$(CONFIG_PIC32_GPIO) += pic32_gpio.o
obj-$(CONFIG_MSM_GPIO) += msm_gpio.o
+obj-$(CONFIG_PM8916_GPIO) += pm8916_gpio.o
diff --git a/drivers/gpio/pm8916_gpio.c b/drivers/gpio/pm8916_gpio.c
new file mode 100644
index 0000000..1abab7f
--- /dev/null
+++ b/drivers/gpio/pm8916_gpio.c
@@ -0,0 +1,302 @@
+/*
+ * Qualcomm pm8916 pmic gpio driver - part of Qualcomm PM8916 PMIC
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski at gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <power/pmic.h>
+#include <spmi/spmi.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <linux/bitops.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* Register offset for each gpio */
+#define REG_OFFSET(x) ((x) * 0x100)
+
+/* Register maps */
+
+/* Type and subtype are shared for all pm8916 peripherals */
+#define REG_TYPE 0x4
+#define REG_SUBTYPE 0x5
+
+#define REG_STATUS 0x08
+#define REG_STATUS_VAL_MASK 0x1
+
+/* MODE_CTL */
+#define REG_CTL 0x40
+#define REG_CTL_MODE_MASK 0x70
+#define REG_CTL_MODE_INPUT 0x00
+#define REG_CTL_MODE_INOUT 0x20
+#define REG_CTL_MODE_OUTPUT 0x10
+#define REG_CTL_OUTPUT_MASK 0x0F
+
+#define REG_DIG_VIN_CTL 0x41
+#define REG_DIG_VIN_VIN0 0
+
+#define REG_DIG_PULL_CTL 0x42
+#define REG_DIG_PULL_NO_PU 0x5
+
+#define REG_DIG_OUT_CTL 0x45
+#define REG_DIG_OUT_CTL_CMOS (0x0 << 4)
+#define REG_DIG_OUT_CTL_DRIVE_L 0x1
+
+#define REG_EN_CTL 0x46
+#define REG_EN_CTL_ENABLE (1 << 7)
+
+struct pm8916_gpio_bank {
+ uint16_t pid; /* Peripheral ID on SPMI bus */
+};
+
+static int pm8916_gpio_set_direction(struct udevice *dev, unsigned offset,
+ bool input, int value)
+{
+ struct pm8916_gpio_bank *priv = dev_get_priv(dev);
+ uint32_t gpio_base = priv->pid + REG_OFFSET(offset);
+ int ret;
+
+ /* Disable the GPIO */
+ ret = pmic_clrsetbits(dev->parent, gpio_base + REG_EN_CTL,
+ REG_EN_CTL_ENABLE, 0);
+ if (ret < 0)
+ return ret;
+
+ /* Select the mode */
+ if (input)
+ ret = pmic_reg_write(dev->parent, gpio_base + REG_CTL,
+ REG_CTL_MODE_INPUT);
+ else
+ ret = pmic_reg_write(dev->parent, gpio_base + REG_CTL,
+ REG_CTL_MODE_INOUT | (value ? 1 : 0));
+ if (ret < 0)
+ return ret;
+
+ /* Set the right pull (no pull) */
+ ret = pmic_reg_write(dev->parent, gpio_base + REG_DIG_PULL_CTL,
+ REG_DIG_PULL_NO_PU);
+ if (ret < 0)
+ return ret;
+
+ /* Configure output pin drivers if needed */
+ if (!input) {
+ /* Select the VIN - VIN0, pin is input so it doesn't matter */
+ ret = pmic_reg_write(dev->parent, gpio_base + REG_DIG_VIN_CTL,
+ REG_DIG_VIN_VIN0);
+ if (ret < 0)
+ return ret;
+
+ /* Set the right dig out control */
+ ret = pmic_reg_write(dev->parent, gpio_base + REG_DIG_OUT_CTL,
+ REG_DIG_OUT_CTL_CMOS |
+ REG_DIG_OUT_CTL_DRIVE_L);
+ if (ret < 0)
+ return ret;
+ }
+
+ /* Enable the GPIO */
+ return pmic_clrsetbits(dev->parent, gpio_base + REG_EN_CTL, 0,
+ REG_EN_CTL_ENABLE);
+}
+
+static int pm8916_gpio_direction_input(struct udevice *dev, unsigned offset)
+{
+ return pm8916_gpio_set_direction(dev, offset, true, 0);
+}
+
+static int pm8916_gpio_direction_output(struct udevice *dev, unsigned offset,
+ int value)
+{
+ return pm8916_gpio_set_direction(dev, offset, false, value);
+}
+
+static int pm8916_gpio_get_function(struct udevice *dev, unsigned offset)
+{
+ struct pm8916_gpio_bank *priv = dev_get_priv(dev);
+ uint32_t gpio_base = priv->pid + REG_OFFSET(offset);
+ int reg;
+
+ /* Set the output value of the gpio */
+ reg = pmic_reg_read(dev->parent, gpio_base + REG_CTL);
+ if (reg < 0)
+ return reg;
+
+ switch (reg & REG_CTL_MODE_MASK) {
+ case REG_CTL_MODE_INPUT:
+ return GPIOF_INPUT;
+ case REG_CTL_MODE_INOUT: /* Fallthrough */
+ case REG_CTL_MODE_OUTPUT:
+ return GPIOF_OUTPUT;
+ default:
+ return GPIOF_UNKNOWN;
+ }
+}
+
+static int pm8916_gpio_get_value(struct udevice *dev, unsigned offset)
+{
+ struct pm8916_gpio_bank *priv = dev_get_priv(dev);
+ uint32_t gpio_base = priv->pid + REG_OFFSET(offset);
+ int reg;
+
+ reg = pmic_reg_read(dev->parent, gpio_base + REG_STATUS);
+ if (reg < 0)
+ return reg;
+
+ return !!(reg & REG_STATUS_VAL_MASK);
+}
+
+static int pm8916_gpio_set_value(struct udevice *dev, unsigned offset,
+ int value)
+{
+ struct pm8916_gpio_bank *priv = dev_get_priv(dev);
+ uint32_t gpio_base = priv->pid + REG_OFFSET(offset);
+
+ /* Set the output value of the gpio */
+ return pmic_clrsetbits(dev->parent, gpio_base + REG_CTL,
+ REG_CTL_OUTPUT_MASK, !!value);
+}
+
+static const struct dm_gpio_ops pm8916_gpio_ops = {
+ .direction_input = pm8916_gpio_direction_input,
+ .direction_output = pm8916_gpio_direction_output,
+ .get_value = pm8916_gpio_get_value,
+ .set_value = pm8916_gpio_set_value,
+ .get_function = pm8916_gpio_get_function,
+};
+
+static int pm8916_gpio_probe(struct udevice *dev)
+{
+ struct pm8916_gpio_bank *priv = dev_get_priv(dev);
+ int reg;
+
+ priv->pid = dev_get_addr(dev);
+ if (priv->pid == FDT_ADDR_T_NONE)
+ return -EINVAL;
+
+ /* Do a sanity check */
+ reg = pmic_reg_read(dev->parent, priv->pid + REG_TYPE);
+ if (reg != 0x10)
+ return -ENODEV;
+
+ reg = pmic_reg_read(dev->parent, priv->pid + REG_SUBTYPE);
+ if (reg != 0x5)
+ return -ENODEV;
+
+ return 0;
+}
+
+static int pm8916_gpio_ofdata_to_platdata(struct udevice *dev)
+{
+ struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev);
+
+ uc_priv->gpio_count = fdtdec_get_int(gd->fdt_blob, dev->of_offset,
+ "gpio-count", 0);
+ uc_priv->bank_name = fdt_getprop(gd->fdt_blob, dev->of_offset,
+ "gpio-bank-name", NULL);
+ if (uc_priv->bank_name == NULL)
+ uc_priv->bank_name = "pm8916";
+
+ return 0;
+}
+
+static const struct udevice_id pm8916_gpio_ids[] = {
+ { .compatible = "qcom,pm8916-gpio" },
+ { }
+};
+
+U_BOOT_DRIVER(gpio_pm8916) = {
+ .name = "gpio_pm8916",
+ .id = UCLASS_GPIO,
+ .of_match = pm8916_gpio_ids,
+ .ofdata_to_platdata = pm8916_gpio_ofdata_to_platdata,
+ .probe = pm8916_gpio_probe,
+ .ops = &pm8916_gpio_ops,
+ .priv_auto_alloc_size = sizeof(struct pm8916_gpio_bank),
+};
+
+
+/* Add pmic buttons as GPIO as well - there is no generic way for now */
+#define PON_INT_RT_STS 0x10
+#define KPDPWR_ON_INT_BIT 0
+#define RESIN_ON_INT_BIT 1
+
+static int pm8941_pwrkey_get_function(struct udevice *dev, unsigned offset)
+{
+ return GPIOF_INPUT;
+}
+
+static int pm8941_pwrkey_get_value(struct udevice *dev, unsigned offset)
+{
+ struct pm8916_gpio_bank *priv = dev_get_priv(dev);
+
+ int reg = pmic_reg_read(dev->parent, priv->pid + PON_INT_RT_STS);
+
+ if (reg < 0)
+ return 0;
+
+ switch (offset) {
+ case 0: /* Power button */
+ return (reg & BIT(KPDPWR_ON_INT_BIT)) != 0;
+ break;
+ case 1: /* Reset button */
+ default:
+ return (reg & BIT(RESIN_ON_INT_BIT)) != 0;
+ break;
+ }
+}
+
+static const struct dm_gpio_ops pm8941_pwrkey_ops = {
+ .get_value = pm8941_pwrkey_get_value,
+ .get_function = pm8941_pwrkey_get_function,
+};
+
+static int pm8941_pwrkey_probe(struct udevice *dev)
+{
+ struct pm8916_gpio_bank *priv = dev_get_priv(dev);
+ int reg;
+
+ priv->pid = dev_get_addr(dev);
+ if (priv->pid == FDT_ADDR_T_NONE)
+ return -EINVAL;
+
+ /* Do a sanity check */
+ reg = pmic_reg_read(dev->parent, priv->pid + REG_TYPE);
+ if (reg != 0x1)
+ return -ENODEV;
+
+ reg = pmic_reg_read(dev->parent, priv->pid + REG_SUBTYPE);
+ if (reg != 0x1)
+ return -ENODEV;
+
+ return 0;
+}
+
+static int pm8941_pwrkey_ofdata_to_platdata(struct udevice *dev)
+{
+ struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev);
+
+ uc_priv->gpio_count = 2;
+ if (uc_priv->bank_name == NULL)
+ uc_priv->bank_name = "pm8916_key";
+
+ return 0;
+}
+
+static const struct udevice_id pm8941_pwrkey_ids[] = {
+ { .compatible = "qcom,pm8916-pwrkey" },
+ { }
+};
+
+U_BOOT_DRIVER(pwrkey_pm8941) = {
+ .name = "pwrkey_pm8916",
+ .id = UCLASS_GPIO,
+ .of_match = pm8941_pwrkey_ids,
+ .ofdata_to_platdata = pm8941_pwrkey_ofdata_to_platdata,
+ .probe = pm8941_pwrkey_probe,
+ .ops = &pm8941_pwrkey_ops,
+ .priv_auto_alloc_size = sizeof(struct pm8916_gpio_bank),
+};
--
2.5.0
More information about the U-Boot
mailing list