[U-Boot] [PATCH][v3] armv8/ls2080ardb: Enable VID support

[Rai Harninder]

This patch enable VID support for ls2080ardb platform.
It uses the common VID driver

Signed-off-by: Rai Harninder <harninder.rai at nxp.com>
---
Changes in v3:
- Call adjust_vdd() so that the voltage gets adjusted
during u-boot boot up itself

Changes in v2
- Use CONFIG_FSL_LSCH3 instead of CONFIG_LAYERSCAPE
  since the latter is defined for other platforms
  as well
- Modify patch description

 .../include/asm/arch-fsl-layerscape/immap_lsch3.h  |    4 ++++
 board/freescale/common/vid.c                       |   15 ++++++++++++++-
 board/freescale/ls2080ardb/ls2080ardb.c            |    8 ++++++++
 include/configs/ls2080ardb.h                       |   16 ++++++++++++++++
 4 files changed, 42 insertions(+), 1 deletions(-)

diff --git a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
index 91f3ce8..4fd58ee 100644
--- a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
+++ b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
@@ -146,6 +146,10 @@ struct ccsr_gur {
 	u8	res_008[0x20-0x8];
 	u32	gpporcr1;	/* General-purpose POR configuration */
 	u32	gpporcr2;	/* General-purpose POR configuration 2 */
+#define FSL_CHASSIS3_DCFG_FUSESR_VID_SHIFT	25
+#define FSL_CHASSIS3_DCFG_FUSESR_VID_MASK	0x1F
+#define FSL_CHASSIS3_DCFG_FUSESR_ALTVID_SHIFT	20
+#define FSL_CHASSIS3_DCFG_FUSESR_ALTVID_MASK	0x1F
 	u32	dcfg_fusesr;	/* Fuse status register */
 	u32	gpporcr3;
 	u32	gpporcr4;
diff --git a/board/freescale/common/vid.c b/board/freescale/common/vid.c
index 1bd65a8..b037643 100644
--- a/board/freescale/common/vid.c
+++ b/board/freescale/common/vid.c
@@ -10,6 +10,8 @@
 #include <asm/io.h>
 #ifdef CONFIG_LS1043A
 #include <asm/arch/immap_lsch2.h>
+#elif defined(CONFIG_FSL_LSCH3)
+#include <asm/arch/immap_lsch3.h>
 #else
 #include <asm/immap_85xx.h>
 #endif
@@ -285,7 +287,7 @@ static int set_voltage(int i2caddress, int vdd)
 int adjust_vdd(ulong vdd_override)
 {
 	int re_enable = disable_interrupts();
-#ifdef CONFIG_LS1043A
+#if defined(CONFIG_LS1043A) || defined(CONFIG_FSL_LSCH3)
 	struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
 #else
 	ccsr_gur_t __iomem *gur =
@@ -362,7 +364,11 @@ int adjust_vdd(ulong vdd_override)
 	}
 
 	/* get the voltage ID from fuse status register */
+#ifdef CONFIG_FSL_LSCH3
+	fusesr = in_le32(&gur->dcfg_fusesr);
+#else
 	fusesr = in_be32(&gur->dcfg_fusesr);
+#endif
 	/*
 	 * VID is used according to the table below
 	 *                ---------------------------------------
@@ -387,6 +393,13 @@ int adjust_vdd(ulong vdd_override)
 		vid = (fusesr >> FSL_CHASSIS2_DCFG_FUSESR_VID_SHIFT) &
 			FSL_CHASSIS2_DCFG_FUSESR_VID_MASK;
 	}
+#elif defined(CONFIG_FSL_LSCH3)
+	vid = (fusesr >> FSL_CHASSIS3_DCFG_FUSESR_ALTVID_SHIFT) &
+		FSL_CHASSIS3_DCFG_FUSESR_ALTVID_MASK;
+	if ((vid == 0) || (vid == FSL_CHASSIS3_DCFG_FUSESR_ALTVID_MASK)) {
+		vid = (fusesr >> FSL_CHASSIS3_DCFG_FUSESR_VID_SHIFT) &
+			FSL_CHASSIS3_DCFG_FUSESR_VID_MASK;
+	}
 #else
 	vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_ALTVID_SHIFT) &
 		FSL_CORENET_DCFG_FUSESR_ALTVID_MASK;
diff --git a/board/freescale/ls2080ardb/ls2080ardb.c b/board/freescale/ls2080ardb/ls2080ardb.c
index c63b639..952b8e5 100644
--- a/board/freescale/ls2080ardb/ls2080ardb.c
+++ b/board/freescale/ls2080ardb/ls2080ardb.c
@@ -122,6 +122,11 @@ int select_i2c_ch_pca9547(u8 ch)
 	return 0;
 }
 
+int i2c_multiplexer_select_vid_channel(u8 channel)
+{
+	return select_i2c_ch_pca9547(channel);
+}
+
 int config_board_mux(int ctrl_type)
 {
 	u8 reg5;
@@ -184,6 +189,9 @@ int misc_init_r(void)
 	if (hwconfig("sdhc"))
 		config_board_mux(MUX_TYPE_SDHC);
 
+	if (adjust_vdd(0))
+		printf("Warning: Adjusting core voltage failed.\n");
+
 	return 0;
 }
 
diff --git a/include/configs/ls2080ardb.h b/include/configs/ls2080ardb.h
index 116dbcd..9a95f31 100644
--- a/include/configs/ls2080ardb.h
+++ b/include/configs/ls2080ardb.h
@@ -14,6 +14,22 @@
 
 #define CONFIG_DISPLAY_BOARDINFO
 
+#define I2C_MUX_CH_VOL_MONITOR		0xa
+#define I2C_VOL_MONITOR_ADDR		0x38
+#define CONFIG_VOL_MONITOR_IR36021_READ
+#define CONFIG_VOL_MONITOR_IR36021_SET
+
+#define CONFIG_VID_FLS_ENV		"ls2080ardb_vdd_mv"
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_VID
+#endif
+/* step the IR regulator in 5mV increments */
+#define IR_VDD_STEP_DOWN		5
+#define IR_VDD_STEP_UP			5
+/* The lowest and highest voltage allowed for LS2080ARDB */
+#define VDD_MV_MIN			819
+#define VDD_MV_MAX			1212
+
 #ifndef __ASSEMBLY__
 unsigned long get_board_sys_clk(void);
 #endif
-- 
1.7.6.GIT