[U-Boot] [PATCH 1/6] net: gem: Add support for reading MAC from I2C EEPROM

[Michal Simek]

Hi Joe,

2016-02-15 17:01 GMT+01:00 Joe Hershberger <joe.hershberger at gmail.com>:

> Hi Bin,
>
> On Sun, Feb 14, 2016 at 6:00 AM, Bin Meng <bmeng.cn at gmail.com> wrote:
> > Hi Michal,
> >
> > On Sun, Feb 14, 2016 at 6:03 PM, Michal Simek <monstr at monstr.eu> wrote:
> >> Hi Bin,
> >>
> >> 2016-02-14 3:25 GMT+01:00 Bin Meng <bmeng.cn at gmail.com>:
> >>>
> >>> Hi Michal,
> >>>
> >>> On Sat, Feb 13, 2016 at 6:39 PM, Michal Simek <monstr at monstr.eu>
> wrote:
> >>> > Add support for reading MAC address from I2C EEPROM.
> >>> >
> >>>
> >>> Is this a feature provided by the GEM MAC IP?
> >>>
> >>> > Signed-off-by: Michal Simek <monstr at monstr.eu>
> >>> > ---
> >>> >
> >>> >  drivers/net/zynq_gem.c | 16 ++++++++++++++++
> >>> >  1 file changed, 16 insertions(+)
> >>> >
> >>> > diff --git a/drivers/net/zynq_gem.c b/drivers/net/zynq_gem.c
> >>> > index b3821c31a91d..ace60c901cb5 100644
> >>> > --- a/drivers/net/zynq_gem.c
> >>> > +++ b/drivers/net/zynq_gem.c
> >>> > @@ -627,6 +627,21 @@ static int zynq_gem_remove(struct udevice *dev)
> >>> >         return 0;
> >>> >  }
> >>> >
> >>> > +static int zynq_gem_read_rom_hwaddr(struct udevice *dev)
> >>> > +{
> >>> > +#if defined(CONFIG_ZYNQ_GEM_EEPROM_ADDR) && \
> >>> > +    defined(CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET)
> >>> > +       struct eth_pdata *pdata = dev_get_platdata(dev);
> >>> > +
> >>> > +       if (eeprom_read(CONFIG_ZYNQ_GEM_EEPROM_ADDR,
> >>> > +                       CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET,
> >>> > +                       pdata->enetaddr,
> ARRAY_SIZE(pdata->enetaddr)))
> >>>
> >>> This call to eeprom_read() looks to me a board-specific feature, that
> >>> an on-board eeprom is used to store the MAC address for the GEM?
> >>>
> >>
> >> Right. it is board specific feature I can
> >> The question is if this should really go to board specific file
> >> or to be the part of DT binding. I didn't look at the kernel if someone
> has
> >> some sort of eeprom binding for this case
> >> but I expect local mac addresses via DT are used. Or passing via command
> >> line does it.
> >>
> >> Anyway there is mac_read_from_eeprom() but it is ancient one.
> >> Do you any preference for the name of function?
> >
> > I think the intention of the read_rom_hwaddr op is to read the MAC
> > address via the ethernet controller defined mechanism (eg: e1000 can
> > read its MAC address from either an EEPROM or an SPI flash), or via
> > SoC defined mechanism (eg: the ethernet IP is only seen on a specific
> > SoC, and reading the MAC address only makes sense on that specific
> > SoC). If this is a board-specific mechanism, I don't think we should
> > put the codes into driver's read_rom_hwaddr(). Again, if it is
> > board-specific, we may not come up with a standard DT binding for such
> > stuff, unless we can enumerate all possible ways for storing MAC
> > address on a board (EEPROM, SPI flash, eMMC, SD)?
>
> Did you see this: https://patchwork.ozlabs.org/patch/573373/
>
> This is the concept I had in mind for handling this sort of thing.
>

This also works for me. I have no problem with both ways. It means this one
or setting
up variable in board init file.
Also is there any hook that mac address will be updated in DTS file
(local-mac-address)
to be the same in u-boot and in Linux.

Thanks,
Michal

-- 
Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91
w: www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel - Microblaze cpu - http://www.monstr.eu/fdt/
Maintainer of Linux kernel - Xilinx Zynq ARM architecture
Microblaze U-BOOT custodian and responsible for u-boot arm zynq platform