[U-Boot] [PATCH 2/7 v3] armv8: ls2080a: update stream ID partitioning info
Stuart Yoder
stuart.yoder at nxp.com
Fri Feb 26 17:31:57 CET 2016
From: Stuart Yoder <stuart.yoder at nxp.com>
-update comments around how stream IDs are partitioned
-stream IDs allocated to PCI are no longer divided up by
controller, but are instead a contiguous range
Signed-off-by: Stuart Yoder <stuart.yoder at nxp.com>
---
-v3
-no changes
.../asm/arch-fsl-layerscape/ls2080a_stream_id.h | 55 ++++++++++++--------
1 file changed, 34 insertions(+), 21 deletions(-)
diff --git a/arch/arm/include/asm/arch-fsl-layerscape/ls2080a_stream_id.h b/arch/arm/include/asm/arch-fsl-layerscape/ls2080a_stream_id.h
index 954104b..ee28323 100644
--- a/arch/arm/include/asm/arch-fsl-layerscape/ls2080a_stream_id.h
+++ b/arch/arm/include/asm/arch-fsl-layerscape/ls2080a_stream_id.h
@@ -7,28 +7,48 @@
#ifndef __FSL_STREAM_ID_H
#define __FSL_STREAM_ID_H
-/* Stream IDs on ls2080a devices are not hardwired and are
+/*
+ * Stream IDs on ls2080a devices are not hardwired and are
* programmed by sw. There are a limited number of stream IDs
* available, and the partitioning of them is scenario dependent.
* This header defines the partitioning between legacy, PCI,
* and DPAA2 devices.
*
- * This partitiong can be customized in this file depending
- * on the specific hardware config-- e.g. perhaps not all
- * PEX controllers are in use.
+ * This partitioning can be customized in this file depending
+ * on the specific hardware config:
+ *
+ * -non-PCI legacy, platform devices (USB, SD/MMC, SATA, DMA)
+ * -all legacy devices get a unique stream ID assigned and programmed in
+ * their AMQR registers by u-boot
+ *
+ * -PCIe
+ * -there is a range of stream IDs set aside for PCI in this
+ * file. U-boot will scan the PCI bus and for each device discovered:
+ * -allocate a streamID
+ * -set a PEXn LUT table entry mapping 'requester ID' to 'stream ID'
+ * -set a msi-map entry in the PEXn controller node in the
+ * device tree (see Documentation/devicetree/bindings/pci/pci-msi.txt
+ * for more info on the msi-map definition)
*
- * On LS2080 stream IDs are programmed in AMQ registers (32-bits) for
+ * -DPAA2
+ * -u-boot will allocate a range of stream IDs to be used by the Management
+ * Complex for containers and will set these values in the MC DPC image.
+ * -the MC is responsible for allocating and setting up 'isolation context
+ * IDs (ICIDs) based on the allocated stream IDs for all DPAA2 devices.
+ *
+ * On ls2080a SoCs stream IDs are programmed in AMQ registers (32-bits) for
* each of the different bus masters. The relationship between
* the AMQ registers and stream IDs is defined in the table below:
* AMQ bit streamID bit
* ---------------------------
- * PL[18] 9
- * BMT[17] 8
- * VA[16] 7
- * [15] -
- * ICID[14:7] -
- * ICID[6:0] 6-0
+ * PL[18] 9 // privilege bit
+ * BMT[17] 8 // bypass translation
+ * VA[16] 7 // reserved
+ * [15] - // unused
+ * ICID[14:7] - // unused
+ * ICID[6:0] 6-0 // isolation context id
* ----------------------------
+ *
*/
#define AMQ_PL_MASK (0x1 << 18) /* priviledge bit */
@@ -46,16 +66,9 @@
#define FSL_SATA2_STREAM_ID 5
#define FSL_DMA_STREAM_ID 6
-/* PCI - programmed in PEXn_LUT by OS */
-/* 4 IDs per controller */
-#define FSL_PEX1_STREAM_ID_START 7
-#define FSL_PEX1_STREAM_ID_END 10
-#define FSL_PEX2_STREAM_ID_START 11
-#define FSL_PEX2_STREAM_ID_END 14
-#define FSL_PEX3_STREAM_ID_START 15
-#define FSL_PEX3_STREAM_ID_END 18
-#define FSL_PEX4_STREAM_ID_START 19
-#define FSL_PEX4_STREAM_ID_END 22
+/* PCI - programmed in PEXn_LUT */
+#define FSL_PEX_STREAM_ID_START 7
+#define FSL_PEX_STREAM_ID_END 22
/* DPAA2 - set in MC DPC and alloced by MC */
#define FSL_DPAA2_STREAM_ID_START 23
--
1.7.9.5
More information about the U-Boot
mailing list