[U-Boot] [RFC PATCH v2 1/5] spl: dfu: add dfu support in SPL

[Ravi Babu]

Traditionally the DFU support is available only
as part 2nd stage boot loader(u-boot) and DFU
is not supported in SPL.

The SPL-DFU feature is useful for boards which
does not have MMC/SD, ethernet boot mechanism
to boot the board and only has USB inteface.

This patch add DFU support in SPL with RAM
memory device support to load and execute u-boot.
And then leverage full functionality DFU in
u-boot to flash boot inital binary images to
factory or bare-metal boards to memory devices
like SPI, eMMC, MMC/SD card using USB interface.

This SPL-DFU support can be enabled through
Menuconfig->Boot Images->Enable SPL-DFU support

Signed-off-by: Ravi Babu <ravibabu at ti.com>
---
 Kconfig              |   27 +++++++++++++++++++++++++++
 common/Makefile      |    1 +
 common/command.c     |    2 +-
 scripts/Makefile.spl |    4 ++++
 4 files changed, 33 insertions(+), 1 deletion(-)

diff --git a/Kconfig b/Kconfig
index ef12f9f..ed3e295 100644
--- a/Kconfig
+++ b/Kconfig
@@ -336,6 +336,33 @@ config SPL_FIT_IMAGE_POST_PROCESS
 	  injected into the FIT creation (i.e. the blobs would have been pre-
 	  processed before being added to the FIT image).
 
+config SPL_DFU_SUPPORT
+	bool "Enable SPL with DFU to load binaries to memory device"
+	depends on USB && TARGET_DRA7XX_EVM
+	help
+	  Currently the SPL does not have capability to load the
+	  binaries or boot images to boot devices like ram,eMMC,SPI,etc.
+	  This feature enables the DFU (Device Firmware Upgarde) in SPL with
+	  RAM memory device support. The ROM code will load and execute
+	  the SPL built with dfu. The user can load binaries (u-boot/kernel) to
+	  selected device partition from host-pc using dfu-utils.
+		This feature will be useful to flash the binaries to factory
+	  or bare-metal boards using USB interface.
+
+choice
+	bool "DFU device selection"
+	depends on SPL_DFU_SUPPORT
+
+config SPL_DFU_RAM
+	bool "RAM device"
+	depends on SPL_DFU_SUPPORT
+	help
+	 select RAM/DDR memory device for loading binary images
+	 (u-boot/kernel) to the selected device partition using
+	 DFU and execute the u-boot/kernel from RAM.
+
+endchoice
+
 config SYS_CLK_FREQ
 	depends on ARC || ARCH_SUNXI
 	int "CPU clock frequency"
diff --git a/common/Makefile b/common/Makefile
index e08cd3e..7a7a1b4 100644
--- a/common/Makefile
+++ b/common/Makefile
@@ -87,6 +87,7 @@ obj-$(CONFIG_USB_KEYBOARD) += usb_kbd.o
 endif # !CONFIG_SPL_BUILD
 
 ifdef CONFIG_SPL_BUILD
+obj-$(CONFIG_SPL_DFU_SUPPORT) += cli_hush.o
 obj-$(CONFIG_SPL_HASH_SUPPORT) += hash.o
 obj-$(CONFIG_ENV_IS_IN_FLASH) += env_flash.o
 obj-$(CONFIG_SPL_YMODEM_SUPPORT) += xyzModem.o
diff --git a/common/command.c b/common/command.c
index e5d9b9c..d1c049c 100644
--- a/common/command.c
+++ b/common/command.c
@@ -520,7 +520,7 @@ enum command_ret_t cmd_process(int flag, int argc, char * const argv[],
 	if (argc > cmdtp->maxargs)
 		rc = CMD_RET_USAGE;
 
-#if defined(CONFIG_CMD_BOOTD)
+#if defined(CONFIG_CMD_BOOTD) && !defined(CONFIG_SPL_BUILD)
 	/* avoid "bootd" recursion */
 	else if (cmdtp->cmd == do_bootd) {
 		if (flag & CMD_FLAG_BOOTD) {
diff --git a/scripts/Makefile.spl b/scripts/Makefile.spl
index 3ba9742..3b70c4d 100644
--- a/scripts/Makefile.spl
+++ b/scripts/Makefile.spl
@@ -57,6 +57,10 @@ libs-y += common/init/
 libs-$(CONFIG_SPL_LIBCOMMON_SUPPORT) += common/ cmd/
 libs-$(CONFIG_SPL_LIBDISK_SUPPORT) += disk/
 libs-y += drivers/
+libs-$(CONFIG_SPL_DFU_SUPPORT) += drivers/dfu/
+libs-$(CONFIG_SPL_DFU_SUPPORT) += drivers/usb/gadget/
+libs-$(CONFIG_SPL_DFU_SUPPORT) += drivers/usb/gadget/udc/
+libs-$(CONFIG_SPL_DFU_SUPPORT) += drivers/usb/dwc3/
 libs-y += dts/
 libs-y += fs/
 libs-$(CONFIG_SPL_LIBGENERIC_SUPPORT) += lib/
-- 
1.7.9.5