[U-Boot] Newbie SPL question for socfpga_sockit

[Marek Vasut]

On 03/02/2016 11:54 PM, Dinh Nguyen wrote:
> CC: Marek Vasut
> 
> On 03/01/2016 08:40 PM, George Broz wrote:
>> On 17 February 2016 at 18:45, Phil Reid <preid at electromag.com.au> wrote:
>>> G'day George
>>>
>>>
>>> On 18/02/2016 5:54 AM, George Broz wrote:
>>>>
>>>> Hello,
>>>>
>>>> Sorry for the newbie question...
>>>>
>>>> I have an Altera/Terasic board (socfpga_sockit) that has issues
>>>> recognizing
>>>> USB storage devices (roughly 60% good / 40% bad):
>>>>
>>
>>>> If I try a later release (e.g. v2016.01 which seems to support the Terasic
>>>> board explicitly) the boot process stops just after loading the SPL.
>>>>
>>>> At this point I have only been changing the u-boot.img component, not the
>>>> SPL (in the a2 partition of the MMC).
>>>>
>>>> The documentation from Altera about generating the SPL seems to require
>>>> using Qsys/Quartus tools which I'd really like to avoid.
>>>>
>>>> I can produce u-boot-spl.bin / u-boot.img from
>>>> make socfpga_sockit_defconfig; make all.
>>>>
>>>> My newbie question ... should be I able to use directly the u-boot-spl.bin
>>>> generated by the build to replace the SPL on the board?
>>>>
>>>
>>> I've just gone thru the process (this week) of getting uboot 2016.01 to boot
>>> on our custom socfpga board.
>>> There where a few issues in getting things going.
>>> If your using the sd card to boot then the current memory layout is not per
>>> the altera documentation.
>>> I had to make the changes below to config to match the altera docs.
>>> Otherwise it hangs just after the SPL.
>>> You also need to use the -dtb image versions with 2016.01 for things to
>>> work.
>>> Again you may need to make sure the uboot device trees match your hardware.
>>> Not all uboot drivers appear to be using the DT as yet.
>>>
>>> Note the SPL is tightly coupled to the board design and potentially the FPGA
>>> image.
>>> If you using bridges or routing HPS resources (eg i2c etc) to the fpga the
>>> SPL configures the muxes.
>>>
>>> There's a script in uboot src at arch\arm\mach-socfpga\qts-filter.sh
>>> That will generate the qts files for you arch.
>>>
>>> I haven't tried the USB stuff as yet.
>>> There are some issues witht eh altera USB port trigger an Over Current event
>>> on device insertation.
>>> They've modified the linux kenerl driver to use external OV current
>>> detection to get around the problem.
>>> My intial workaround was to insert USB device prior to power on.
>>> I haven't looked at the uboot USB driver yet to see what's in there.
>>>
>>>
>>> --
>>> Regards
>>> Phil Reid
>>>
>>>
>>> diff --git a/include/configs/socfpga_common.h
>>> b/include/configs/socfpga_common.h
>>> index a09e906..3a1b59b 100644 (file)
>>> --- a/include/configs/socfpga_common.h
>>> +++ b/include/configs/socfpga_common.h
>>> @@ -357,13 +357,13 @@ unsigned int cm_get_qspi_controller_clk_hz(void);
>>>
>>> /* SPL SDMMC boot support */
>>> #ifdef CONFIG_SPL_MMC_SUPPORT
>>> +#define CONFIG_SPL_LIBDISK_SUPPORT
>>> #if defined(CONFIG_SPL_FAT_SUPPORT) || defined(CONFIG_SPL_EXT_SUPPORT)
>>> #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 2
>>> #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot-dtb.img"
>>> -#define CONFIG_SPL_LIBDISK_SUPPORT
>>> #else
>>> -#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 3
>>> -#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0xa00 /* offset 2560 sect
>>> (1M+256k) */
>>> +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION 3
>>> +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
>>> #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 800 /* 400 KB */
>>> #endif
>>> #endif
>>>
>>>
>>
>> Thanks, Phil!
>>
>> Sorry for the delayed response - got called away, but am back to this
>> now. I patched
>> socfpga_common.h and re-built the project. I picked up
>> spl/u-boot-spl-dtb.sfp and
>> u-boot-dtb.img and transferred them to the SD card with:
>>
>> dd if=u-boot-spl-dtb.sfp of=/dev/sdf3 bs=64k seek=0
>> dd if=u-boot-dtb.img of=/dev/sdf3 bs=64k seek=4
>>
> 
> You can just do a 'make u-boot-with-spl.sfp' and burn the
> u-boot-with-spl.sfp file straight to the a2 partition, or sdf3.
> 
>> Tried this with both the original DT set (socfpga.dtsi, socfpga_cyclone.dtsi,
>> socfpga_cyclone5_sockit.dts) that came with the u-boot v2016.01 download and
>> also an Altera-patched DT set that I've used to boot into Linux numerous times.
>>
>> When I start up the board I get:
>>
>> U-Boot SPL 2016.01 (Mar 01 2016 - 17:28:14)
>> drivers/ddr/altera/sequencer.c: Preparing to start memory calibration
>> drivers/ddr/altera/sequencer.c: CALIBRATION FAILED
>> drivers/ddr/altera/sequencer.c: Calibration complete
>> SDRAM calibration failed.
>> ### ERROR ### Please RESET the board ###
>>
>> I'm not a Quartus user, so I haven't done anything with the
>> qts-filter.sh script you
>> mentioned. Do I need to? I don't have any custom FPGA logic - it's
>> just the Terasic
>> board out of the box.
>>
> 
> I just tested U-Boot(v2016.03-rc3) and USB is not working on the devkit
> or sockit. It's failing to detect my mass storage device.
> 
> Debugging...

Try dcache off ... does it work ?

-- 
Best regards,
Marek Vasut