[U-Boot] [PATCH 6/6 v2] i2c: designware_i2c: Add support for PCI(e) based I2C cores (x86)
Stefan Roese
sr at denx.de
Wed Mar 23 06:46:28 CET 2016
This patch adds support for the PCI(e) based I2C cores. Which can be
found for example on the Intel Bay Trail SoC. It has 7 I2C controllers
implemented as PCI devices.
This patch also adds the fixed values for the timing registers for
BayTrail which are taken from the Linux designware I2C driver.
Signed-off-by: Stefan Roese <sr at denx.de>
Cc: Simon Glass <sjg at chromium.org>
Cc: Bin Meng <bmeng.cn at gmail.com>
Cc: Marek Vasut <marex at denx.de>
Cc: Heiko Schocher <hs at denx.de>
---
v2:
- Use device_is_on_pci_bus(dev) in designware_i2c_probe()
drivers/i2c/designware_i2c.c | 131 +++++++++++++++++++++++++++++++++++++++----
1 file changed, 119 insertions(+), 12 deletions(-)
diff --git a/drivers/i2c/designware_i2c.c b/drivers/i2c/designware_i2c.c
index 886897c..23c5985 100644
--- a/drivers/i2c/designware_i2c.c
+++ b/drivers/i2c/designware_i2c.c
@@ -8,11 +8,32 @@
#include <common.h>
#include <dm.h>
#include <i2c.h>
+#include <pci.h>
#include <asm/io.h>
#include "designware_i2c.h"
+struct dw_scl_sda_cfg {
+ u32 ss_hcnt;
+ u32 fs_hcnt;
+ u32 ss_lcnt;
+ u32 fs_lcnt;
+ u32 sda_hold;
+};
+
+#ifdef CONFIG_X86
+/* BayTrail HCNT/LCNT/SDA hold time */
+static struct dw_scl_sda_cfg byt_config = {
+ .ss_hcnt = 0x200,
+ .fs_hcnt = 0x55,
+ .ss_lcnt = 0x200,
+ .fs_lcnt = 0x99,
+ .sda_hold = 0x6,
+};
+#endif
+
struct dw_i2c {
struct i2c_regs *regs;
+ struct dw_scl_sda_cfg *scl_sda_cfg;
};
static void dw_i2c_enable(struct i2c_regs *i2c_base, bool enable)
@@ -42,6 +63,7 @@ static void dw_i2c_enable(struct i2c_regs *i2c_base, bool enable)
* Set the i2c speed.
*/
static unsigned int __dw_i2c_set_bus_speed(struct i2c_regs *i2c_base,
+ struct dw_scl_sda_cfg *scl_sda_cfg,
unsigned int speed)
{
unsigned int cntl;
@@ -61,34 +83,55 @@ static unsigned int __dw_i2c_set_bus_speed(struct i2c_regs *i2c_base,
cntl = (readl(&i2c_base->ic_con) & (~IC_CON_SPD_MSK));
switch (i2c_spd) {
+#ifndef CONFIG_X86 /* No High-speed for BayTrail yet */
case IC_SPEED_MODE_MAX:
- cntl |= IC_CON_SPD_HS;
- hcnt = (IC_CLK * MIN_HS_SCL_HIGHTIME) / NANO_TO_MICRO;
+ cntl |= IC_CON_SPD_SS;
+ if (scl_sda_cfg) {
+ hcnt = scl_sda_cfg->fs_hcnt;
+ lcnt = scl_sda_cfg->fs_lcnt;
+ } else {
+ hcnt = (IC_CLK * MIN_HS_SCL_HIGHTIME) / NANO_TO_MICRO;
+ lcnt = (IC_CLK * MIN_HS_SCL_LOWTIME) / NANO_TO_MICRO;
+ }
writel(hcnt, &i2c_base->ic_hs_scl_hcnt);
- lcnt = (IC_CLK * MIN_HS_SCL_LOWTIME) / NANO_TO_MICRO;
writel(lcnt, &i2c_base->ic_hs_scl_lcnt);
break;
+#endif
case IC_SPEED_MODE_STANDARD:
cntl |= IC_CON_SPD_SS;
- hcnt = (IC_CLK * MIN_SS_SCL_HIGHTIME) / NANO_TO_MICRO;
+ if (scl_sda_cfg) {
+ hcnt = scl_sda_cfg->ss_hcnt;
+ lcnt = scl_sda_cfg->ss_lcnt;
+ } else {
+ hcnt = (IC_CLK * MIN_SS_SCL_HIGHTIME) / NANO_TO_MICRO;
+ lcnt = (IC_CLK * MIN_SS_SCL_LOWTIME) / NANO_TO_MICRO;
+ }
writel(hcnt, &i2c_base->ic_ss_scl_hcnt);
- lcnt = (IC_CLK * MIN_SS_SCL_LOWTIME) / NANO_TO_MICRO;
writel(lcnt, &i2c_base->ic_ss_scl_lcnt);
break;
case IC_SPEED_MODE_FAST:
default:
cntl |= IC_CON_SPD_FS;
- hcnt = (IC_CLK * MIN_FS_SCL_HIGHTIME) / NANO_TO_MICRO;
+ if (scl_sda_cfg) {
+ hcnt = scl_sda_cfg->fs_hcnt;
+ lcnt = scl_sda_cfg->fs_lcnt;
+ } else {
+ hcnt = (IC_CLK * MIN_FS_SCL_HIGHTIME) / NANO_TO_MICRO;
+ lcnt = (IC_CLK * MIN_FS_SCL_LOWTIME) / NANO_TO_MICRO;
+ }
writel(hcnt, &i2c_base->ic_fs_scl_hcnt);
- lcnt = (IC_CLK * MIN_FS_SCL_LOWTIME) / NANO_TO_MICRO;
writel(lcnt, &i2c_base->ic_fs_scl_lcnt);
break;
}
writel(cntl, &i2c_base->ic_con);
+ /* Configure SDA Hold Time if required */
+ if (scl_sda_cfg)
+ writel(scl_sda_cfg->sda_hold, &i2c_base->ic_sda_hold);
+
/* Enable back i2c now speed set */
dw_i2c_enable(i2c_base, true);
@@ -315,7 +358,7 @@ static void __dw_i2c_init(struct i2c_regs *i2c_base, int speed, int slaveaddr)
writel(IC_TX_TL, &i2c_base->ic_tx_tl);
writel(IC_STOP_DET, &i2c_base->ic_intr_mask);
#ifndef CONFIG_DM_I2C
- __dw_i2c_set_bus_speed(i2c_base, speed);
+ __dw_i2c_set_bus_speed(i2c_base, NULL, speed);
writel(slaveaddr, &i2c_base->ic_sar);
#endif
@@ -356,7 +399,7 @@ static unsigned int dw_i2c_set_bus_speed(struct i2c_adapter *adap,
unsigned int speed)
{
adap->speed = speed;
- return __dw_i2c_set_bus_speed(i2c_get_base(adap), speed);
+ return __dw_i2c_set_bus_speed(i2c_get_base(adap), NULL, speed);
}
static void dw_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr)
@@ -447,7 +490,7 @@ static int designware_i2c_set_bus_speed(struct udevice *bus, unsigned int speed)
{
struct dw_i2c *i2c = dev_get_priv(bus);
- return __dw_i2c_set_bus_speed(i2c->regs, speed);
+ return __dw_i2c_set_bus_speed(i2c->regs, i2c->scl_sda_cfg, speed);
}
static int designware_i2c_probe_chip(struct udevice *bus, uint chip_addr,
@@ -470,14 +513,61 @@ static int designware_i2c_probe(struct udevice *bus)
{
struct dw_i2c *priv = dev_get_priv(bus);
- /* Save base address from device-tree */
- priv->regs = (struct i2c_regs *)dev_get_addr(bus);
+ if (device_is_on_pci_bus(bus)) {
+#ifdef CONFIG_DM_PCI
+ /* Save base address from PCI BAR */
+ priv->regs = (struct i2c_regs *)
+ dm_pci_map_bar(bus, PCI_BASE_ADDRESS_0, PCI_REGION_MEM);
+#ifdef CONFIG_X86
+ /* Use BayTrail specific timing values */
+ priv->scl_sda_cfg = &byt_config;
+#endif
+#endif
+ } else {
+ /* Save base address from device-tree */
+
+ /*
+ * On x86, "fdt_addr_t" is 64bit but "void *" only 32bit.
+ * So assigning the register base directly in dev_get_addr()
+ * results in this compilation warning:
+ * warning: cast to pointer from integer of different size
+ *
+ * Using this macro __UINTPTR_TYPE__, allows us to cast the
+ * result of dev_get_addr() into a 32bit value before casting
+ * it to the pointer (struct i2c_regs *).
+ */
+ priv->regs =
+ (struct i2c_regs *)(__UINTPTR_TYPE__)dev_get_addr(bus);
+ }
__dw_i2c_init(priv->regs, 0, 0);
return 0;
}
+static int designware_i2c_bind(struct udevice *dev)
+{
+ static int num_cards;
+ char name[20];
+
+ /* Create a unique device name for PCI type devices */
+ if (device_is_on_pci_bus(dev)) {
+ /*
+ * ToDo:
+ * Setting req_seq in the driver is probably not recommended.
+ * But without a DT alias the number is not configured. And
+ * using this driver is impossible for PCIe I2C devices.
+ * This can be removed, once a better (correct) way for this
+ * is found and implemented.
+ */
+ dev->req_seq = num_cards;
+ sprintf(name, "i2c_designware#%u", num_cards++);
+ device_set_name(dev, name);
+ }
+
+ return 0;
+}
+
static const struct dm_i2c_ops designware_i2c_ops = {
.xfer = designware_i2c_xfer,
.probe_chip = designware_i2c_probe_chip,
@@ -493,9 +583,26 @@ U_BOOT_DRIVER(i2c_designware) = {
.name = "i2c_designware",
.id = UCLASS_I2C,
.of_match = designware_i2c_ids,
+ .bind = designware_i2c_bind,
.probe = designware_i2c_probe,
.priv_auto_alloc_size = sizeof(struct dw_i2c),
.ops = &designware_i2c_ops,
};
+#ifdef CONFIG_X86
+static struct pci_device_id designware_pci_supported[] = {
+ /* Intel BayTrail has 7 I2C controller located on the PCI bus */
+ { PCI_VDEVICE(INTEL, 0x0f41) },
+ { PCI_VDEVICE(INTEL, 0x0f42) },
+ { PCI_VDEVICE(INTEL, 0x0f43) },
+ { PCI_VDEVICE(INTEL, 0x0f44) },
+ { PCI_VDEVICE(INTEL, 0x0f45) },
+ { PCI_VDEVICE(INTEL, 0x0f46) },
+ { PCI_VDEVICE(INTEL, 0x0f47) },
+ {},
+};
+
+U_BOOT_PCI_DEVICE(i2c_designware, designware_pci_supported);
+#endif
+
#endif /* CONFIG_DM_I2C */
--
2.7.4
More information about the U-Boot
mailing list