[U-Boot] [PATCH] sunxi: Add defconfig and dts for Orange Pi 2 SBC
Hans de Goede
hdegoede at redhat.com
Wed Mar 23 11:13:44 CET 2016
The Orange Pi 2 is a SBC based on the Allwinner H3 SoC with a uSD slot,
4 USB ports connected via a USB-2 hub, a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, USB OTG, HDMI,
a TRRS headphone jack for stereo out and composite out, a microphone,
an IR receiver, a CSI connector, 2 LEDs, a 3 pin UART header
and a 40-pin GPIO header.
The added dts file is identical to the one submitted to the upstream
kernel.
Signed-off-by: Hans de Goede <hdegoede at redhat.com>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/sun8i-h3-orangepi-2.dts | 186 +++++++++++++++++++++++++++++++++++
board/sunxi/MAINTAINERS | 1 +
configs/orangepi_2_defconfig | 18 ++++
4 files changed, 206 insertions(+)
create mode 100644 arch/arm/dts/sun8i-h3-orangepi-2.dts
create mode 100644 configs/orangepi_2_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 6112f52..ae75c76 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -201,6 +201,7 @@ dtb-$(CONFIG_MACH_SUN8I_A83T) += \
sun8i-a83t-cubietruck-plus.dtb \
sun8i-a83t-sinovoip-bpi-m3.dtb
dtb-$(CONFIG_MACH_SUN8I_H3) += \
+ sun8i-h3-orangepi-2.dtb \
sun8i-h3-orangepi-pc.dtb \
sun8i-h3-orangepi-plus.dtb
dtb-$(CONFIG_MACH_SUN9I) += \
diff --git a/arch/arm/dts/sun8i-h3-orangepi-2.dts b/arch/arm/dts/sun8i-h3-orangepi-2.dts
new file mode 100644
index 0000000..f93f5d1
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-orangepi-2.dts
@@ -0,0 +1,186 @@
+/*
+ * Copyright (C) 2016 Hans de Goede <hdegoede at redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Xunlong Orange Pi 2";
+ compatible = "xunlong,orangepi-2", "allwinner,sun8i-h3";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
+
+ status_led {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>;
+ };
+
+ pwr_led {
+ label = "orangepi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ r_gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sw_r_opc>;
+
+ sw2 {
+ label = "sw2";
+ linux,code = <BTN_1>;
+ gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>;
+ };
+
+ sw4 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_pwrseq_pin_orangepi>;
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 WIFI_EN */
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&pio {
+ leds_opc: led_pins at 0 {
+ allwinner,pins = "PA15";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&r_pio {
+ leds_r_opc: led_pins at 0 {
+ allwinner,pins = "PL10";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ sw_r_opc: key_pins at 0 {
+ allwinner,pins = "PL3", "PL4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin at 0 {
+ allwinner,pins = "PL7";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usb1_vbus_pin_a {
+ allwinner,pins = "PG13";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
index 603cda7..5f2f4fe 100644
--- a/board/sunxi/MAINTAINERS
+++ b/board/sunxi/MAINTAINERS
@@ -54,6 +54,7 @@ F: configs/Wits_Pro_A20_DKT_defconfig
F: include/configs/sun8i.h
F: configs/ga10h_v1_1_defconfig
F: configs/gt90h_v4_defconfig
+F: configs/orangepi_2_defconfig
F: configs/orangepi_pc_defconfig
F: configs/orangepi_plus_defconfig
F: configs/polaroid_mid2809pxe04_defconfig
diff --git a/configs/orangepi_2_defconfig b/configs/orangepi_2_defconfig
new file mode 100644
index 0000000..ff9ac09
--- /dev/null
+++ b/configs/orangepi_2_defconfig
@@ -0,0 +1,18 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN8I_H3=y
+CONFIG_DRAM_CLK=672
+CONFIG_DRAM_ZQ=3881979
+CONFIG_DRAM_ODT_EN=y
+CONFIG_MMC0_CD_PIN="PF6"
+# CONFIG_VIDEO is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-orangepi-2"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_GPIO=y
+CONFIG_SY8106A_POWER=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB1_VBUS_PIN="PG13"
--
2.7.3
More information about the U-Boot
mailing list