[U-Boot] [PATCH 18/19] arm: imx: add i.MX6SLL EVK board support
Peng Fan
peng.fan at nxp.com
Thu Nov 24 07:48:00 CET 2016
Add i.MX6SLL EVK board support.
1. Add imx6sll-evk device tree.
2. Enable SDHC/I2C/UART.
3. Enable REGULATOR/PMIC/I2C/GPIO/SDHC/PINCTRL driver.
Boot Log:
U-Boot 2016.11-00127-gc635871-dirty (Nov 24 2016 - 13:28:19 +0800)
CPU: Freescale i.MX6SLL rev1.0 at 792MHz
CPU: Commercial temperature grade (0C to 95C)Reset cause: POR
Model: Freescale i.MX6SLL EVK Board
Board: MX6SLL EVK
DRAM: 2 GiB
i2c bus 0 at 35258368, no gpio pinctrl state.
PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <peng.fan at nxp.com>
Cc: Stefano Babic <sbabic at denx.de>
---
arch/arm/cpu/armv7/mx6/Kconfig | 7 +
arch/arm/dts/Makefile | 1 +
arch/arm/dts/imx6sll-evk.dts | 801 +++++++++++++++++++++++++++++++++
board/freescale/mx6sllevk/Kconfig | 12 +
board/freescale/mx6sllevk/Makefile | 6 +
board/freescale/mx6sllevk/imximage.cfg | 121 +++++
board/freescale/mx6sllevk/mx6sllevk.c | 131 ++++++
configs/mx6sllevk_defconfig | 36 ++
include/configs/mx6sllevk.h | 152 +++++++
9 files changed, 1267 insertions(+)
create mode 100644 arch/arm/dts/imx6sll-evk.dts
create mode 100644 board/freescale/mx6sllevk/Kconfig
create mode 100644 board/freescale/mx6sllevk/Makefile
create mode 100644 board/freescale/mx6sllevk/imximage.cfg
create mode 100644 board/freescale/mx6sllevk/mx6sllevk.c
create mode 100644 configs/mx6sllevk_defconfig
create mode 100644 include/configs/mx6sllevk.h
diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig
index 72bc083..c5674c5 100644
--- a/arch/arm/cpu/armv7/mx6/Kconfig
+++ b/arch/arm/cpu/armv7/mx6/Kconfig
@@ -124,6 +124,12 @@ config TARGET_MX6SLEVK
bool "mx6slevk"
select SUPPORT_SPL
+config TARGET_MX6SLLEVK
+ bool "mx6sll evk"
+ select MX6SLL
+ select DM
+ select DM_THERMAL
+
config TARGET_MX6SXSABRESD
bool "mx6sxsabresd"
select MX6SX
@@ -244,6 +250,7 @@ source "board/freescale/mx6qarm2/Kconfig"
source "board/freescale/mx6qsabreauto/Kconfig"
source "board/freescale/mx6sabresd/Kconfig"
source "board/freescale/mx6slevk/Kconfig"
+source "board/freescale/mx6sllevk/Kconfig"
source "board/freescale/mx6sxsabresd/Kconfig"
source "board/freescale/mx6sxsabreauto/Kconfig"
source "board/freescale/mx6ul_14x14_evk/Kconfig"
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 2c5b2f2..4b4356b 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -285,6 +285,7 @@ dtb-$(CONFIG_VF610) += vf500-colibri.dtb \
bk4r1.dtb
dtb-$(CONFIG_MX6) += imx6ull-14x14-evk.dtb \
+ imx6sll-evk.dtb \
imx6dl-icore.dtb \
imx6q-icore.dtb
diff --git a/arch/arm/dts/imx6sll-evk.dts b/arch/arm/dts/imx6sll-evk.dts
new file mode 100644
index 0000000..b4af007
--- /dev/null
+++ b/arch/arm/dts/imx6sll-evk.dts
@@ -0,0 +1,801 @@
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "imx6sll.dtsi"
+
+/ {
+ model = "Freescale i.MX6SLL EVK Board";
+ compatible = "fsl,imx6sll-evk", "fsl,imx6sll";
+
+ memory {
+ reg = <0x80000000 0x80000000>;
+ };
+
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ status = "okay";
+ };
+
+ battery: max8903 at 0 {
+ compatible = "fsl,max8903-charger";
+ pinctrl-names = "default";
+ dok_input = <&gpio4 13 1>;
+ uok_input = <&gpio4 13 1>;
+ chg_input = <&gpio4 15 1>;
+ flt_input = <&gpio4 14 1>;
+ fsl,dcm_always_high;
+ fsl,dc_valid;
+ fsl,adc_disable;
+ status = "okay";
+ };
+
+ pxp_v4l2_out {
+ compatible = "fsl,imx6sl-pxp-v4l2";
+ status = "okay";
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_usb_otg1_vbus: regulator at 0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usb_otg2_vbus: regulator at 1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "usb_otg2_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_aud3v: regulator at 2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "wm8962-supply-3v15";
+ regulator-min-microvolt = <3150000>;
+ regulator-max-microvolt = <3150000>;
+ regulator-boot-on;
+ };
+
+ reg_aud4v: regulator at 3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "wm8962-supply-4v2";
+ regulator-min-microvolt = <4325000>;
+ regulator-max-microvolt = <4325000>;
+ regulator-boot-on;
+ };
+
+ reg_lcd: regulator at 4 {
+ compatible = "regulator-fixed";
+ reg = <4>;
+ regulator-name = "lcd-pwr";
+ gpio = <&gpio4 8 0>;
+ enable-active-high;
+ };
+
+ reg_sd1_vmmc: sd1_vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "SD1_SPWR";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_sd2_vmmc: sd2_vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "eMMC-VCCQ";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
+
+ reg_sd3_vmmc: sd3_vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "SD3_WIFI";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ gpio = <&gpio4 4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ };
+
+ sound {
+ compatible = "fsl,imx6sl-evk-wm8962", "fsl,imx-audio-wm8962";
+ model = "wm8962-audio";
+ cpu-dai = <&ssi2>;
+ audio-codec = <&codec>;
+ audio-routing =
+ "Headphone Jack", "HPOUTL",
+ "Headphone Jack", "HPOUTR",
+ "Ext Spk", "SPKOUTL",
+ "Ext Spk", "SPKOUTR",
+ "AMIC", "MICBIAS",
+ "IN3R", "AMIC";
+ mux-int-port = <2>;
+ mux-ext-port = <3>;
+ codec-master;
+ hp-det-gpios = <&gpio4 24 1>;
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux3>;
+ status = "okay";
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6SLL_CLK_PLL4_AUDIO_DIV>;
+ assigned-clock-rates = <393216000>;
+};
+
+&cpu0 {
+ arm-supply = <&sw1a_reg>;
+ soc-supply = <&sw1c_reg>;
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ pmic: pfuze100 at 08 {
+ compatible = "fsl,pfuze100";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw1c_reg: sw1c {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3b_reg: sw3b {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ regulator-always-on;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+
+ max17135: max17135 at 48 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_max17135>;
+ compatible = "maxim,max17135";
+ reg = <0x48>;
+ status = "okay";
+
+ vneg_pwrup = <1>;
+ gvee_pwrup = <2>;
+ vpos_pwrup = <10>;
+ gvdd_pwrup = <12>;
+ gvdd_pwrdn = <1>;
+ vpos_pwrdn = <2>;
+ gvee_pwrdn = <8>;
+ vneg_pwrdn = <10>;
+ gpio_pmic_pwrgood = <&gpio2 13 0>;
+ gpio_pmic_vcom_ctrl = <&gpio2 3 0>;
+ gpio_pmic_wakeup = <&gpio2 14 0>;
+ gpio_pmic_v3p3 = <&gpio2 7 0>;
+ gpio_pmic_intr = <&gpio2 12 0>;
+
+ regulators {
+ DISPLAY_reg: DISPLAY {
+ regulator-name = "DISPLAY";
+ };
+
+ GVDD_reg: GVDD {
+ /* 20v */
+ regulator-name = "GVDD";
+ };
+
+ GVEE_reg: GVEE {
+ /* -22v */
+ regulator-name = "GVEE";
+ };
+
+ HVINN_reg: HVINN {
+ /* -22v */
+ regulator-name = "HVINN";
+ };
+
+ HVINP_reg: HVINP {
+ /* 20v */
+ regulator-name = "HVINP";
+ };
+
+ VCOM_reg: VCOM {
+ regulator-name = "VCOM";
+ /* 2's-compliment, -4325000 */
+ regulator-min-microvolt = <0xffbe0178>;
+ /* 2's-compliment, -500000 */
+ regulator-max-microvolt = <0xfff85ee0>;
+ };
+
+ VNEG_reg: VNEG {
+ /* -15v */
+ regulator-name = "VNEG";
+ };
+
+ VPOS_reg: VPOS {
+ /* 15v */
+ regulator-name = "VPOS";
+ };
+
+ V3P3_reg: V3P3 {
+ regulator-name = "V3P3";
+ };
+ };
+ };
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ codec: wm8962 at 1a {
+ compatible = "wlf,wm8962";
+ reg = <0x1a>;
+ clocks = <&clks IMX6SLL_CLK_EXTERN_AUDIO>;
+ DCVDD-supply = <&vgen3_reg>;
+ DBVDD-supply = <®_aud3v>;
+ AVDD-supply = <&vgen3_reg>;
+ CPVDD-supply = <&vgen3_reg>;
+ MICVDD-supply = <®_aud3v>;
+ PLLVDD-supply = <&vgen3_reg>;
+ SPKVDD1-supply = <®_aud4v>;
+ SPKVDD2-supply = <®_aud4v>;
+ amic-mono;
+ };
+};
+
+&gpc {
+ fsl,ldo-bypass = <1>;
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ imx6sll-evk {
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ MX6SLL_PAD_KEY_ROW7__GPIO4_IO07 0x17059
+ MX6SLL_PAD_GPIO4_IO22__GPIO4_IO22 0x17059
+ MX6SLL_PAD_KEY_COL3__GPIO3_IO30 0x17059
+ /*
+ * Must set the LVE of pad SD2_RESET, otherwise current
+ * leakage through eMMC chip will pull high the VCCQ to
+ * 2.6v, which will impact SD1 and SD3 SD3.0 voltage switch.
+ */
+ MX6SLL_PAD_SD2_RESET__GPIO4_IO27 0x417059
+ MX6SLL_PAD_KEY_COL4__GPIO4_IO00 0x17059
+ MX6SLL_PAD_REF_CLK_32K__GPIO3_IO22 0x17059 /* SD3 CD */
+ MX6SLL_PAD_KEY_COL6__GPIO4_IO04 0x17059 /*SD3 RESET */
+ MX6SLL_PAD_KEY_COL5__GPIO4_IO02 0x17059
+ MX6SLL_PAD_GPIO4_IO24__GPIO4_IO24 0x17059 /* HP DETECT */
+ /* CHG_FLT, CHG_UOK/DOK, CHG_STATUS */
+ MX6SLL_PAD_ECSPI2_MISO__GPIO4_IO14 0x17000
+ MX6SLL_PAD_ECSPI2_MOSI__GPIO4_IO13 0x17000
+ MX6SLL_PAD_ECSPI2_SS0__GPIO4_IO15 0x17000
+ >;
+ };
+
+ pinctrl_audmux3: audmux3grp {
+ fsl,pins = <
+ MX6SLL_PAD_AUD_TXC__AUD3_TXC 0x4130b0
+ MX6SLL_PAD_AUD_TXFS__AUD3_TXFS 0x4130b0
+ MX6SLL_PAD_AUD_TXD__AUD3_TXD 0x4110b0
+ MX6SLL_PAD_AUD_RXD__AUD3_RXD 0x4130b0
+ MX6SLL_PAD_AUD_MCLK__AUDIO_CLK_OUT 0x4130b0
+ >;
+ };
+
+ pinctrl_csi1: csi1grp {
+ fsl,pins = <
+ MX6SLL_PAD_EPDC_GDRL__CSI_MCLK 0x1b088
+ MX6SLL_PAD_EPDC_GDCLK__CSI_PIXCLK 0x1b088
+ MX6SLL_PAD_EPDC_GDSP__CSI_VSYNC 0x1b088
+ MX6SLL_PAD_EPDC_GDOE__CSI_HSYNC 0x1b088
+ MX6SLL_PAD_EPDC_DATA02__CSI_DATA02 0x1b088
+ MX6SLL_PAD_EPDC_DATA03__CSI_DATA03 0x1b088
+ MX6SLL_PAD_EPDC_DATA04__CSI_DATA04 0x1b088
+ MX6SLL_PAD_EPDC_DATA05__CSI_DATA05 0x1b088
+ MX6SLL_PAD_EPDC_DATA06__CSI_DATA06 0x1b088
+ MX6SLL_PAD_EPDC_DATA07__CSI_DATA07 0x1b088
+ MX6SLL_PAD_EPDC_SDCLK__CSI_DATA08 0x1b088
+ MX6SLL_PAD_EPDC_SDLE__CSI_DATA09 0x1b088
+ MX6SLL_PAD_EPDC_SDSHR__GPIO1_IO26 0x80000000
+ MX6SLL_PAD_EPDC_SDOE__GPIO1_IO25 0x80000000
+ >;
+ };
+
+ pinctrl_epdc0: epdcgrp0 {
+ fsl,pins = <
+ MX6SLL_PAD_EPDC_DATA00__EPDC_DATA00 0x100b1
+ MX6SLL_PAD_EPDC_DATA01__EPDC_DATA01 0x100b1
+ MX6SLL_PAD_EPDC_DATA02__EPDC_DATA02 0x100b1
+ MX6SLL_PAD_EPDC_DATA03__EPDC_DATA03 0x100b1
+ MX6SLL_PAD_EPDC_DATA04__EPDC_DATA04 0x100b1
+ MX6SLL_PAD_EPDC_DATA05__EPDC_DATA05 0x100b1
+ MX6SLL_PAD_EPDC_DATA06__EPDC_DATA06 0x100b1
+ MX6SLL_PAD_EPDC_DATA07__EPDC_DATA07 0x100b1
+ MX6SLL_PAD_EPDC_DATA08__EPDC_DATA08 0x100b1
+ MX6SLL_PAD_EPDC_DATA09__EPDC_DATA09 0x100b1
+ MX6SLL_PAD_EPDC_DATA10__EPDC_DATA10 0x100b1
+ MX6SLL_PAD_EPDC_DATA11__EPDC_DATA11 0x100b1
+ MX6SLL_PAD_EPDC_DATA12__EPDC_DATA12 0x100b1
+ MX6SLL_PAD_EPDC_DATA13__EPDC_DATA13 0x100b1
+ MX6SLL_PAD_EPDC_DATA14__EPDC_DATA14 0x100b1
+ MX6SLL_PAD_EPDC_DATA15__EPDC_DATA15 0x100b1
+ MX6SLL_PAD_EPDC_SDCLK__EPDC_SDCLK_P 0x100b1
+ MX6SLL_PAD_EPDC_SDLE__EPDC_SDLE 0x100b1
+ MX6SLL_PAD_EPDC_SDOE__EPDC_SDOE 0x100b1
+ MX6SLL_PAD_EPDC_SDSHR__EPDC_SDSHR 0x100b1
+ MX6SLL_PAD_EPDC_SDCE0__EPDC_SDCE0 0x100b1
+ MX6SLL_PAD_EPDC_GDCLK__EPDC_GDCLK 0x100b1
+ MX6SLL_PAD_EPDC_GDOE__EPDC_GDOE 0x100b1
+ MX6SLL_PAD_EPDC_GDRL__EPDC_GDRL 0x100b1
+ MX6SLL_PAD_EPDC_GDSP__EPDC_GDSP 0x100b1
+ >;
+ };
+
+ pinctrl_lcdif_dat: lcdifdatgrp {
+ fsl,pins = <
+ MX6SLL_PAD_LCD_DATA00__LCD_DATA00 0x79
+ MX6SLL_PAD_LCD_DATA01__LCD_DATA01 0x79
+ MX6SLL_PAD_LCD_DATA02__LCD_DATA02 0x79
+ MX6SLL_PAD_LCD_DATA03__LCD_DATA03 0x79
+ MX6SLL_PAD_LCD_DATA04__LCD_DATA04 0x79
+ MX6SLL_PAD_LCD_DATA05__LCD_DATA05 0x79
+ MX6SLL_PAD_LCD_DATA06__LCD_DATA06 0x79
+ MX6SLL_PAD_LCD_DATA07__LCD_DATA07 0x79
+ MX6SLL_PAD_LCD_DATA08__LCD_DATA08 0x79
+ MX6SLL_PAD_LCD_DATA09__LCD_DATA09 0x79
+ MX6SLL_PAD_LCD_DATA10__LCD_DATA10 0x79
+ MX6SLL_PAD_LCD_DATA11__LCD_DATA11 0x79
+ MX6SLL_PAD_LCD_DATA12__LCD_DATA12 0x79
+ MX6SLL_PAD_LCD_DATA13__LCD_DATA13 0x79
+ MX6SLL_PAD_LCD_DATA14__LCD_DATA14 0x79
+ MX6SLL_PAD_LCD_DATA15__LCD_DATA15 0x79
+ MX6SLL_PAD_LCD_DATA16__LCD_DATA16 0x79
+ MX6SLL_PAD_LCD_DATA17__LCD_DATA17 0x79
+ MX6SLL_PAD_LCD_DATA18__LCD_DATA18 0x79
+ MX6SLL_PAD_LCD_DATA19__LCD_DATA19 0x79
+ MX6SLL_PAD_LCD_DATA20__LCD_DATA20 0x79
+ MX6SLL_PAD_LCD_DATA21__LCD_DATA21 0x79
+ MX6SLL_PAD_LCD_DATA22__LCD_DATA22 0x79
+ MX6SLL_PAD_LCD_DATA23__LCD_DATA23 0x79
+ >;
+ };
+
+ pinctrl_lcdif_ctrl: lcdifctrlgrp {
+ fsl,pins = <
+ MX6SLL_PAD_LCD_CLK__LCD_CLK 0x79
+ MX6SLL_PAD_LCD_ENABLE__LCD_ENABLE 0x79
+ MX6SLL_PAD_LCD_HSYNC__LCD_HSYNC 0x79
+ MX6SLL_PAD_LCD_VSYNC__LCD_VSYNC 0x79
+ MX6SLL_PAD_LCD_RESET__LCD_RESET 0x79
+ MX6SLL_PAD_ECSPI1_SCLK__GPIO4_IO08 0x79
+ >;
+ };
+
+ pinctrl_max17135: max17135grp-1 {
+ fsl,pins = <
+ MX6SLL_PAD_EPDC_PWR_STAT__GPIO2_IO13 0x80000000 /* pwrgood */
+ MX6SLL_PAD_EPDC_VCOM0__GPIO2_IO03 0x80000000 /* vcom_ctrl */
+ MX6SLL_PAD_EPDC_PWR_WAKE__GPIO2_IO14 0x80000000 /* wakeup */
+ MX6SLL_PAD_EPDC_PWR_CTRL0__GPIO2_IO07 0x80000000 /* v3p3 */
+ MX6SLL_PAD_EPDC_PWR_IRQ__GPIO2_IO12 0x80000000 /* pwr int */
+ >;
+ };
+
+ pinctrl_spdif: spdifgrp {
+ fsl,pins = <
+ MX6SLL_PAD_SD2_DATA4__SPDIF_OUT 0x4130b0
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6SLL_PAD_UART1_TXD__UART1_DCE_TX 0x1b0b1
+ MX6SLL_PAD_UART1_RXD__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6SLL_PAD_KEY_ROW1__GPIO3_IO27 0x1b0b1 /* bt reg on */
+ MX6SLL_PAD_ECSPI1_MOSI__UART5_DCE_TX 0x1b0b1
+ MX6SLL_PAD_ECSPI1_SCLK__UART5_DCE_RX 0x1b0b1
+ MX6SLL_PAD_ECSPI1_SS0__UART5_DCE_CTS 0x1b0b1
+ MX6SLL_PAD_ECSPI1_MISO__UART5_DCE_RTS 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5dte: uart5dtegrp {
+ fsl,pins = <
+ MX6SLL_PAD_ECSPI1_MOSI__UART5_DTE_RX 0x1b0b1
+ MX6SLL_PAD_ECSPI1_SCLK__UART5_DTE_TX 0x1b0b1
+ MX6SLL_PAD_ECSPI1_SS0__UART5_DTE_RTS 0x1b0b1
+ MX6SLL_PAD_ECSPI1_MISO__UART5_DTE_CTS 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6SLL_PAD_SD1_CMD__SD1_CMD 0x17059
+ MX6SLL_PAD_SD1_CLK__SD1_CLK 0x13059
+ MX6SLL_PAD_SD1_DATA0__SD1_DATA0 0x17059
+ MX6SLL_PAD_SD1_DATA1__SD1_DATA1 0x17059
+ MX6SLL_PAD_SD1_DATA2__SD1_DATA2 0x17059
+ MX6SLL_PAD_SD1_DATA3__SD1_DATA3 0x17059
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
+ fsl,pins = <
+ MX6SLL_PAD_SD1_CMD__SD1_CMD 0x170b9
+ MX6SLL_PAD_SD1_CLK__SD1_CLK 0x130b9
+ MX6SLL_PAD_SD1_DATA0__SD1_DATA0 0x170b9
+ MX6SLL_PAD_SD1_DATA1__SD1_DATA1 0x170b9
+ MX6SLL_PAD_SD1_DATA2__SD1_DATA2 0x170b9
+ MX6SLL_PAD_SD1_DATA3__SD1_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
+ fsl,pins = <
+ MX6SLL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6SLL_PAD_SD1_CLK__SD1_CLK 0x130f9
+ MX6SLL_PAD_SD1_DATA0__SD1_DATA0 0x170f9
+ MX6SLL_PAD_SD1_DATA1__SD1_DATA1 0x170f9
+ MX6SLL_PAD_SD1_DATA2__SD1_DATA2 0x170f9
+ MX6SLL_PAD_SD1_DATA3__SD1_DATA3 0x170f9
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6SLL_PAD_SD2_CMD__SD2_CMD 0x17059
+ MX6SLL_PAD_SD2_CLK__SD2_CLK 0x13059
+ MX6SLL_PAD_SD2_DATA0__SD2_DATA0 0x17059
+ MX6SLL_PAD_SD2_DATA1__SD2_DATA1 0x17059
+ MX6SLL_PAD_SD2_DATA2__SD2_DATA2 0x17059
+ MX6SLL_PAD_SD2_DATA3__SD2_DATA3 0x17059
+ MX6SLL_PAD_SD2_DATA4__SD2_DATA4 0x17059
+ MX6SLL_PAD_SD2_DATA5__SD2_DATA5 0x17059
+ MX6SLL_PAD_SD2_DATA6__SD2_DATA6 0x17059
+ MX6SLL_PAD_SD2_DATA7__SD2_DATA7 0x17059
+ MX6SLL_PAD_GPIO4_IO21__SD2_STROBE 0x413059
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp_100mhz {
+ fsl,pins = <
+ MX6SLL_PAD_SD2_CMD__SD2_CMD 0x170b9
+ MX6SLL_PAD_SD2_CLK__SD2_CLK 0x130b9
+ MX6SLL_PAD_SD2_DATA0__SD2_DATA0 0x170b9
+ MX6SLL_PAD_SD2_DATA1__SD2_DATA1 0x170b9
+ MX6SLL_PAD_SD2_DATA2__SD2_DATA2 0x170b9
+ MX6SLL_PAD_SD2_DATA3__SD2_DATA3 0x170b9
+ MX6SLL_PAD_SD2_DATA4__SD2_DATA4 0x170b9
+ MX6SLL_PAD_SD2_DATA5__SD2_DATA5 0x170b9
+ MX6SLL_PAD_SD2_DATA6__SD2_DATA6 0x170b9
+ MX6SLL_PAD_SD2_DATA7__SD2_DATA7 0x170b9
+ MX6SLL_PAD_GPIO4_IO21__SD2_STROBE 0x4130b9
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp_200mhz {
+ fsl,pins = <
+ MX6SLL_PAD_SD2_CMD__SD2_CMD 0x170f9
+ MX6SLL_PAD_SD2_CLK__SD2_CLK 0x130f9
+ MX6SLL_PAD_SD2_DATA0__SD2_DATA0 0x170f9
+ MX6SLL_PAD_SD2_DATA1__SD2_DATA1 0x170f9
+ MX6SLL_PAD_SD2_DATA2__SD2_DATA2 0x170f9
+ MX6SLL_PAD_SD2_DATA3__SD2_DATA3 0x170f9
+ MX6SLL_PAD_SD2_DATA4__SD2_DATA4 0x170f9
+ MX6SLL_PAD_SD2_DATA5__SD2_DATA5 0x170f9
+ MX6SLL_PAD_SD2_DATA6__SD2_DATA6 0x170f9
+ MX6SLL_PAD_SD2_DATA7__SD2_DATA7 0x170f9
+ MX6SLL_PAD_GPIO4_IO21__SD2_STROBE 0x4130f9
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6SLL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6SLL_PAD_SD3_CLK__SD3_CLK 0x13059
+ MX6SLL_PAD_SD3_DATA0__SD3_DATA0 0x17059
+ MX6SLL_PAD_SD3_DATA1__SD3_DATA1 0x17059
+ MX6SLL_PAD_SD3_DATA2__SD3_DATA2 0x17059
+ MX6SLL_PAD_SD3_DATA3__SD3_DATA3 0x17059
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3grp_100mhz {
+ fsl,pins = <
+ MX6SLL_PAD_SD3_CMD__SD3_CMD 0x170b9
+ MX6SLL_PAD_SD3_CLK__SD3_CLK 0x130b9
+ MX6SLL_PAD_SD3_DATA0__SD3_DATA0 0x170b9
+ MX6SLL_PAD_SD3_DATA1__SD3_DATA1 0x170b9
+ MX6SLL_PAD_SD3_DATA2__SD3_DATA2 0x170b9
+ MX6SLL_PAD_SD3_DATA3__SD3_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3grp_200mhz {
+ fsl,pins = <
+ MX6SLL_PAD_SD3_CMD__SD3_CMD 0x170f9
+ MX6SLL_PAD_SD3_CLK__SD3_CLK 0x130f9
+ MX6SLL_PAD_SD3_DATA0__SD3_DATA0 0x170f9
+ MX6SLL_PAD_SD3_DATA1__SD3_DATA1 0x170f9
+ MX6SLL_PAD_SD3_DATA2__SD3_DATA2 0x170f9
+ MX6SLL_PAD_SD3_DATA3__SD3_DATA3 0x170f9
+ >;
+ };
+
+ pinctrl_usbotg1: usbotg1grp {
+ fsl,pins = <
+ MX6SLL_PAD_EPDC_PWR_COM__USB_OTG1_ID 0x17059
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6SLL_PAD_I2C1_SCL__I2C1_SCL 0x4001b8b1
+ MX6SLL_PAD_I2C1_SDA__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6SLL_PAD_AUD_RXFS__I2C3_SCL 0x4041b8b1
+ MX6SLL_PAD_AUD_RXC__I2C3_SDA 0x4041b8b1
+ >;
+ };
+
+ pinctrl_pwm1: pmw1grp {
+ fsl,pins = <
+ MX6SLL_PAD_PWM1__PWM1_OUT 0x110b0
+ >;
+ };
+ };
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcdif_dat
+ &pinctrl_lcdif_ctrl>;
+ lcd-supply = <®_lcd>;
+ display = <&display>;
+ status = "okay";
+
+ display: display {
+ bits-per-pixel = <16>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <33500000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <89>;
+ hfront-porch = <164>;
+ vback-porch = <23>;
+ vfront-porch = <10>;
+ hsync-len = <10>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&pxp {
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ fsl,uart-has-rtscts;
+ /* for DTE mode, add below change */
+ /* fsl,dte-mode; */
+ /* pinctrl-0 = <&pinctrl_uart5dte>; */
+ status = "disabled";
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ cd-gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+ keep-power-in-suspend;
+ enable-sdio-wakeup;
+ vmmc-supply = <®_sd1_vmmc>;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+ vqmmc-supply = <®_sd2_vmmc>;
+ bus-width = <8>;
+ no-removable;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
+ keep-power-in-suspend;
+ enable-sdio-wakeup;
+ vmmc-supply = <®_sd3_vmmc>;
+ status = "okay";
+};
+
+&usbotg1 {
+ vbus-supply = <®_usb_otg1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg1>;
+ disable-over-current;
+ srp-disable;
+ hnp-disable;
+ adp-disable;
+ status = "okay";
+};
+
+&usbotg2 {
+ vbus-supply = <®_usb_otg2_vbus>;
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&epdc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_epdc0>;
+ V3P3-supply = <&V3P3_reg>;
+ VCOM-supply = <&VCOM_reg>;
+ DISPLAY-supply = <&DISPLAY_reg>;
+ status = "okay";
+};
+
+&ssi2 {
+ status = "okay";
+};
diff --git a/board/freescale/mx6sllevk/Kconfig b/board/freescale/mx6sllevk/Kconfig
new file mode 100644
index 0000000..4ba9bbf
--- /dev/null
+++ b/board/freescale/mx6sllevk/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_MX6SLLEVK
+
+config SYS_BOARD
+ default "mx6sllevk"
+
+config SYS_VENDOR
+ default "freescale"
+
+config SYS_CONFIG_NAME
+ default "mx6sllevk"
+
+endif
diff --git a/board/freescale/mx6sllevk/Makefile b/board/freescale/mx6sllevk/Makefile
new file mode 100644
index 0000000..667fcb0
--- /dev/null
+++ b/board/freescale/mx6sllevk/Makefile
@@ -0,0 +1,6 @@
+# (C) Copyright 2016 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := mx6sllevk.o
diff --git a/board/freescale/mx6sllevk/imximage.cfg b/board/freescale/mx6sllevk/imximage.cfg
new file mode 100644
index 0000000..53fb74f
--- /dev/null
+++ b/board/freescale/mx6sllevk/imximage.cfg
@@ -0,0 +1,121 @@
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi, sd (the board has no nand neither onenand)
+ */
+
+BOOT_FROM sd
+
+#ifdef CONFIG_SECURE_BOOT
+CSF CONFIG_CSF_SIZE
+#endif
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type Address Value
+ *
+ * where:
+ * Addr-type register length (1,2 or 4 bytes)
+ * Address absolute address of the register
+ * value value to be stored in the register
+ */
+
+/* Enable all clocks */
+DATA 4 0x020c4068 0xffffffff
+DATA 4 0x020c406c 0xffffffff
+DATA 4 0x020c4070 0xffffffff
+DATA 4 0x020c4074 0xffffffff
+DATA 4 0x020c4078 0xffffffff
+DATA 4 0x020c407c 0xffffffff
+DATA 4 0x020c4080 0xffffffff
+
+DATA 4 0x020E0550 0x00080000
+DATA 4 0x020E0534 0x00000000
+DATA 4 0x020E02AC 0x00000030
+DATA 4 0x020E0548 0x00000030
+DATA 4 0x020E052C 0x00000030
+DATA 4 0x020E0530 0x00020000
+DATA 4 0x020E02B0 0x00003030
+DATA 4 0x020E02B4 0x00003030
+DATA 4 0x020E02B8 0x00003030
+DATA 4 0x020E02BC 0x00003030
+DATA 4 0x020E0540 0x00020000
+DATA 4 0x020E0544 0x00000030
+DATA 4 0x020E054C 0x00000030
+DATA 4 0x020E0554 0x00000030
+DATA 4 0x020E0558 0x00000030
+DATA 4 0x020E0294 0x00000030
+DATA 4 0x020E0298 0x00000030
+DATA 4 0x020E029C 0x00000030
+DATA 4 0x020E02A0 0x00000030
+DATA 4 0x020E02C0 0x00082030
+
+DATA 4 0x021B001C 0x00008000
+
+DATA 4 0x021B0800 0xA1390003
+DATA 4 0x021B085c 0x084700C7
+DATA 4 0x021B0890 0x00400000
+DATA 4 0x021B0848 0x3F393B3C
+DATA 4 0x021B0850 0x262C3826
+DATA 4 0x021B081C 0x33333333
+DATA 4 0x021B0820 0x33333333
+DATA 4 0x021B0824 0x33333333
+DATA 4 0x021B0828 0x33333333
+
+DATA 4 0x021B082C 0xf3333333
+DATA 4 0x021B0830 0xf3333333
+DATA 4 0x021B0834 0xf3333333
+DATA 4 0x021B0838 0xf3333333
+DATA 4 0x021B08C0 0x24922492
+DATA 4 0x021B08b8 0x00000800
+
+DATA 4 0x021B0004 0x00020052
+DATA 4 0x021B000C 0x53574333
+DATA 4 0x021B0010 0x00100B22
+DATA 4 0x021B0038 0x00170778
+DATA 4 0x021B0014 0x00C700DB
+DATA 4 0x021B0018 0x00201718
+DATA 4 0x021B002C 0x0F9F26D2
+DATA 4 0x021B0030 0x009F0E10
+DATA 4 0x021B0040 0x0000005F
+DATA 4 0x021B0000 0xC4190000
+
+DATA 4 0x021B083C 0x20000000
+
+DATA 4 0x021B001C 0x00008050
+DATA 4 0x021B001C 0x00008058
+DATA 4 0x021B001C 0x003F8030
+DATA 4 0x021B001C 0x003F8038
+DATA 4 0x021B001C 0xFF0A8030
+DATA 4 0x021B001C 0xFF0A8038
+DATA 4 0x021B001C 0x04028030
+DATA 4 0x021B001C 0x04028038
+DATA 4 0x021B001C 0x83018030
+DATA 4 0x021B001C 0x83018038
+DATA 4 0x021B001C 0x01038030
+DATA 4 0x021B001C 0x01038038
+
+DATA 4 0x021B0020 0x00001800
+DATA 4 0x021B0800 0xA1390003
+DATA 4 0x021B0004 0x00020052
+DATA 4 0x021B0404 0x00011006
+DATA 4 0x021B001C 0x00000000
diff --git a/board/freescale/mx6sllevk/mx6sllevk.c b/board/freescale/mx6sllevk/mx6sllevk.c
new file mode 100644
index 0000000..7630957
--- /dev/null
+++ b/board/freescale/mx6sllevk/mx6sllevk.c
@@ -0,0 +1,131 @@
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/io.h>
+#include <common.h>
+#include <linux/sizes.h>
+#include <mmc.h>
+#include <power/pmic.h>
+#include <power/pfuze100_pmic.h>
+#include "../common/pfuze.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+int dram_init(void)
+{
+ gd->ram_size = PHYS_SDRAM_SIZE;
+
+ return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+ MX6_PAD_UART1_TXD__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_UART1_RXD__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const wdog_pads[] = {
+ MX6_PAD_WDOG_B__WDOG1_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+ imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+#ifdef CONFIG_DM_PMIC_PFUZE100
+int power_init_board(void)
+{
+ struct udevice *dev;
+ int ret;
+ u32 dev_id, rev_id, i;
+ u32 switch_num = 6;
+ u32 offset = PFUZE100_SW1CMODE;
+
+ ret = pmic_get("pfuze100", &dev);
+ if (ret == -ENODEV)
+ return 0;
+
+ if (ret != 0)
+ return ret;
+
+ dev_id = pmic_reg_read(dev, PFUZE100_DEVICEID);
+ rev_id = pmic_reg_read(dev, PFUZE100_REVID);
+ printf("PMIC: PFUZE100! DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id);
+
+
+ /* Init mode to APS_PFM */
+ pmic_reg_write(dev, PFUZE100_SW1ABMODE, APS_PFM);
+
+ for (i = 0; i < switch_num - 1; i++)
+ pmic_reg_write(dev, offset + i * SWITCH_SIZE, APS_PFM);
+
+ /* set SW1AB staby volatage 0.975V */
+ pmic_clrsetbits(dev, PFUZE100_SW1ABSTBY, 0x3f, 0x1b);
+
+ /* set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
+ pmic_clrsetbits(dev, PFUZE100_SW1ABCONF, 0xc0, 0x40);
+
+ /* set SW1C staby volatage 0.975V */
+ pmic_clrsetbits(dev, PFUZE100_SW1CSTBY, 0x3f, 0x1b);
+
+ /* set SW1C/VDDSOC step ramp up time to from 16us to 4us/25mV */
+ pmic_clrsetbits(dev, PFUZE100_SW1CCONF, 0xc0, 0x40);
+
+ return 0;
+}
+#endif
+
+int board_early_init_f(void)
+{
+ setup_iomux_uart();
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* Address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+ return 0;
+}
+
+int board_late_init(void)
+{
+ imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: MX6SLL EVK\n");
+
+ return 0;
+}
+
+int board_mmc_get_env_dev(int devno)
+{
+ return devno;
+}
+
+int mmc_map_to_kernel_blk(int devno)
+{
+ return devno;
+}
diff --git a/configs/mx6sllevk_defconfig b/configs/mx6sllevk_defconfig
new file mode 100644
index 0000000..8ae049e
--- /dev/null
+++ b/configs/mx6sllevk_defconfig
@@ -0,0 +1,36 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_TARGET_MX6SLLEVK=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6sll-evk"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6sllevk/imximage.cfg"
+CONFIG_BOOTDELAY=3
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_OF_CONTROL=y
+# CONFIG_BLK is not set
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+# CONFIG_DM_MMC_OPS is not set
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
diff --git a/include/configs/mx6sllevk.h b/include/configs/mx6sllevk.h
new file mode 100644
index 0000000..b9f25cf
--- /dev/null
+++ b/include/configs/mx6sllevk.h
@@ -0,0 +1,152 @@
+/*
+ * Copyright 2013-2016 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the Freescale i.MX6SL EVK board.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include "mx6_common.h"
+
+#ifdef CONFIG_SECURE_BOOT
+#ifndef CONFIG_CSF_SIZE
+#define CONFIG_CSF_SIZE 0x4000
+#endif
+#endif
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (16 * SZ_1M)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART1_BASE
+
+/* I2C Configs */
+#ifdef CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
+#define CONFIG_SYS_I2C_SPEED 100000
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "epdc_waveform=epdc_splash.bin\0" \
+ "script=boot.scr\0" \
+ "image=zImage\0" \
+ "console=ttymxc0\0" \
+ "fdt_high=0xffffffff\0" \
+ "initrd_high=0xffffffff\0" \
+ "fdt_file=imx6sll-evk.dtb\0" \
+ "fdt_addr=0x83000000\0" \
+ "boot_fdt=try\0" \
+ "ip_dyn=yes\0" \
+ "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
+ "mmcpart=1\0" \
+ "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+ "mmcautodetect=yes\0" \
+ "mmcargs=setenv bootargs console=${console},${baudrate} " \
+ "root=${mmcroot}\0" \
+ "loadbootscript=" \
+ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if run loadfdt; then " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootz; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "bootz; " \
+ "fi;\0" \
+ "netargs=setenv bootargs console=${console},${baudrate} " \
+ "root=/dev/nfs " \
+ "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+ "netboot=echo Booting from net ...; " \
+ "usb start; " \
+ "run netargs; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${image}; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootz; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "bootz; " \
+ "fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+ "mmc dev ${mmcdev};" \
+ "mmc dev ${mmcdev}; if mmc rescan; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loadimage; then " \
+ "run mmcboot; " \
+ "else run netboot; " \
+ "fi; " \
+ "fi; " \
+ "else run netboot; fi"
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_MEMTEST_START 0x80000000
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + SZ_128M)
+
+#define CONFIG_STACKSIZE SZ_128K
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+#define PHYS_SDRAM_SIZE SZ_2G
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* Environment organization */
+#define CONFIG_ENV_SIZE SZ_8K
+#define CONFIG_SYS_MMC_ENV_PART 0 /* user partition */
+#define CONFIG_MMCROOT "/dev/mmcblk0p2" /* USDHC1 */
+
+#define CONFIG_ENV_OFFSET (12 * SZ_64K)
+#define CONFIG_ENV_IS_IN_MMC
+
+/* MMC Configs */
+#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC1_BASE_ADDR
+#define CONFIG_SYS_FSL_USDHC_NUM 3
+#define CONFIG_SYS_MMC_ENV_DEV 0 /* USDHC1 */
+
+#define CONFIG_IMX_THERMAL
+
+#define CONFIG_IOMUX_LPSR
+
+#endif /* __CONFIG_H */
--
2.6.2
More information about the U-Boot
mailing list