[U-Boot] [PATCH v3 9/9] ARM: SPI: stm32: add stm32f746 qspi driver
Michael Kurz
michi.kurz at gmail.com
Thu Nov 24 20:10:47 CET 2016
This patch adds support for the QSPI IP found in stm32f7 devices.
Signed-off-by: Michael Kurz <michi.kurz at gmail.com>
---
This currently hard disables any multi i/o in the device tree, as it is
impossible to get this working without interpreting the commands of the
spi-flash framework in the xfer function and setting the used i/o lines
accordingly.
As i understand a spi-nor framework is currently in the making which
addresses these problems. Should i base this driver on the new
framework or is it ok in the current form and should later be ported to
the new one?
Changes in v3:
- Moved qspi rcc bits into rcc header
- Drop 'add missing flag to micron/stm N25Q128 flash chips' patch
Changes in v2:
- Replaced bit shifts and masks with BIT() and GENMASK() macro
arch/arm/dts/stm32f746-disco.dts | 4 +-
arch/arm/include/asm/arch-stm32f7/rcc.h | 1 +
arch/arm/include/asm/arch-stm32f7/stm32_periph.h | 6 +-
arch/arm/mach-stm32/stm32f7/clock.c | 3 +
board/st/stm32f746-disco/stm32f746-disco.c | 60 +++
configs/stm32f746-disco_defconfig | 7 +
drivers/spi/Kconfig | 8 +
drivers/spi/Makefile | 1 +
drivers/spi/stm32_qspi.c | 628 +++++++++++++++++++++++
9 files changed, 714 insertions(+), 4 deletions(-)
create mode 100644 drivers/spi/stm32_qspi.c
diff --git a/arch/arm/dts/stm32f746-disco.dts b/arch/arm/dts/stm32f746-disco.dts
index 7b652f0..b58889a 100644
--- a/arch/arm/dts/stm32f746-disco.dts
+++ b/arch/arm/dts/stm32f746-disco.dts
@@ -146,8 +146,8 @@
#size-cells = <1>;
compatible = "micron,n25q128a13", "spi-flash";
spi-max-frequency = <108000000>;
- spi-tx-bus-width = <4>;
- spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <1>;
memory-map = <0x90000000 0x1000000>;
reg = <0>;
};
diff --git a/arch/arm/include/asm/arch-stm32f7/rcc.h b/arch/arm/include/asm/arch-stm32f7/rcc.h
index 23eec5e..0f8d50b 100644
--- a/arch/arm/include/asm/arch-stm32f7/rcc.h
+++ b/arch/arm/include/asm/arch-stm32f7/rcc.h
@@ -31,6 +31,7 @@
* RCC AHB3ENR specific definitions
*/
#define RCC_AHB3ENR_FMC_EN BIT(0)
+#define RCC_AHB3ENR_QSPI_EN BIT(1)
/*
* RCC APB1ENR specific definitions
diff --git a/arch/arm/include/asm/arch-stm32f7/stm32_periph.h b/arch/arm/include/asm/arch-stm32f7/stm32_periph.h
index 508b5f2..3c5604a 100644
--- a/arch/arm/include/asm/arch-stm32f7/stm32_periph.h
+++ b/arch/arm/include/asm/arch-stm32f7/stm32_periph.h
@@ -15,8 +15,9 @@
*
*/
enum periph_id {
- UART1_GPIOA_9_10 = 0,
- UART2_GPIOD_5_6,
+ PERIPH_ID_USART1 = 37,
+
+ PERIPH_ID_QUADSPI = 92,
};
enum periph_clock {
@@ -37,6 +38,7 @@ enum periph_clock {
TIMER2_CLOCK_CFG,
FMC_CLOCK_CFG,
STMMAC_CLOCK_CFG,
+ QSPI_CLOCK_CFG,
};
#endif /* __ASM_ARM_ARCH_PERIPH_H */
diff --git a/arch/arm/mach-stm32/stm32f7/clock.c b/arch/arm/mach-stm32/stm32f7/clock.c
index 8b3d3fd..e1ee173 100644
--- a/arch/arm/mach-stm32/stm32f7/clock.c
+++ b/arch/arm/mach-stm32/stm32f7/clock.c
@@ -266,6 +266,9 @@ void clock_setup(int peripheral)
setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_ETHMAC_RX_EN);
setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_ETHMAC_TX_EN);
break;
+ case QSPI_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb3enr, RCC_AHB3ENR_QSPI_EN);
+ break;
default:
break;
}
diff --git a/board/st/stm32f746-disco/stm32f746-disco.c b/board/st/stm32f746-disco/stm32f746-disco.c
index 6c16138..7ed7bf7 100644
--- a/board/st/stm32f746-disco/stm32f746-disco.c
+++ b/board/st/stm32f746-disco/stm32f746-disco.c
@@ -326,6 +326,60 @@ static int stmmac_setup(void)
}
#endif
+#ifdef CONFIG_STM32_QSPI
+const struct stm32_gpio_ctl gpio_ctl_qspi_9 = {
+ .mode = STM32_GPIO_MODE_AF,
+ .otype = STM32_GPIO_OTYPE_PP,
+ .speed = STM32_GPIO_SPEED_100M,
+ .pupd = STM32_GPIO_PUPD_NO,
+ .af = STM32_GPIO_AF9
+};
+
+const struct stm32_gpio_ctl gpio_ctl_qspi_10 = {
+ .mode = STM32_GPIO_MODE_AF,
+ .otype = STM32_GPIO_OTYPE_PP,
+ .speed = STM32_GPIO_SPEED_100M,
+ .pupd = STM32_GPIO_PUPD_NO,
+ .af = STM32_GPIO_AF10
+};
+
+static const struct stm32_gpio_dsc qspi_af9_gpio[] = {
+ {STM32_GPIO_PORT_B, STM32_GPIO_PIN_2}, /* QUADSPI_CLK */
+ {STM32_GPIO_PORT_D, STM32_GPIO_PIN_11}, /* QUADSPI_BK1_IO0 */
+ {STM32_GPIO_PORT_D, STM32_GPIO_PIN_12}, /* QUADSPI_BK1_IO1 */
+ {STM32_GPIO_PORT_D, STM32_GPIO_PIN_13}, /* QUADSPI_BK1_IO3 */
+ {STM32_GPIO_PORT_E, STM32_GPIO_PIN_2}, /* QUADSPI_BK1_IO2 */
+};
+
+static const struct stm32_gpio_dsc qspi_af10_gpio[] = {
+ {STM32_GPIO_PORT_B, STM32_GPIO_PIN_6}, /* QUADSPI_BK1_NCS */
+};
+
+static int qspi_setup(void)
+{
+ int res = 0;
+ int i;
+
+ clock_setup(GPIO_B_CLOCK_CFG);
+ clock_setup(GPIO_D_CLOCK_CFG);
+ clock_setup(GPIO_E_CLOCK_CFG);
+
+ for (i = 0; i < ARRAY_SIZE(qspi_af9_gpio); i++) {
+ res = stm32_gpio_config(&qspi_af9_gpio[i], &gpio_ctl_qspi_9);
+ if (res)
+ return res;
+ }
+
+ for (i = 0; i < ARRAY_SIZE(qspi_af10_gpio); i++) {
+ res = stm32_gpio_config(&qspi_af10_gpio[i], &gpio_ctl_qspi_10);
+ if (res)
+ return res;
+ }
+
+ return 0;
+}
+#endif
+
u32 get_board_rev(void)
{
return 0;
@@ -346,6 +400,12 @@ int board_early_init_f(void)
return res;
#endif
+#ifdef CONFIG_STM32_QSPI
+ res = qspi_setup();
+ if (res)
+ return res;
+#endif
+
return 0;
}
diff --git a/configs/stm32f746-disco_defconfig b/configs/stm32f746-disco_defconfig
index 7301380..4a81f02 100644
--- a/configs/stm32f746-disco_defconfig
+++ b/configs/stm32f746-disco_defconfig
@@ -12,6 +12,7 @@ CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Hit SPACE in %d seconds to stop autoboot.\n"
CONFIG_AUTOBOOT_STOP_STR=" "
# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_SF=y
# CONFIG_CMD_FPGA is not set
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@@ -24,8 +25,14 @@ CONFIG_CMD_TIMER=y
CONFIG_OF_CONTROL=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_NETCONSOLE=y
+CONFIG_MTD=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_STMICRO=y
CONFIG_DM_ETH=y
CONFIG_ETH_DESIGNWARE=y
# CONFIG_SPL_SERIAL_PRESENT is not set
+CONFIG_DM_SPI=y
+CONFIG_STM32_QSPI=y
CONFIG_OF_LIBFDT_OVERLAY=y
# CONFIG_EFI_LOADER is not set
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 0f51b3a..f3f7dbe 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -124,6 +124,14 @@ config SANDBOX_SPI
};
};
+config STM32_QSPI
+ bool "STM32F7 QSPI driver"
+ depends on STM32F7
+ help
+ Enable the STM32F7 Quad-SPI (QSPI) driver. This driver can be
+ used to access the SPI NOR flash chips on platforms embedding
+ this ST IP core.
+
config TEGRA114_SPI
bool "nVidia Tegra114 SPI driver"
help
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 247c5f6..59068d0 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -46,6 +46,7 @@ obj-$(CONFIG_ROCKCHIP_SPI) += rk_spi.o
obj-$(CONFIG_SANDBOX_SPI) += sandbox_spi.o
obj-$(CONFIG_SH_SPI) += sh_spi.o
obj-$(CONFIG_SH_QSPI) += sh_qspi.o
+obj-$(CONFIG_STM32_QSPI) += stm32_qspi.o
obj-$(CONFIG_TEGRA114_SPI) += tegra114_spi.o
obj-$(CONFIG_TEGRA20_SFLASH) += tegra20_sflash.o
obj-$(CONFIG_TEGRA20_SLINK) += tegra20_slink.o
diff --git a/drivers/spi/stm32_qspi.c b/drivers/spi/stm32_qspi.c
new file mode 100644
index 0000000..123a1f3
--- /dev/null
+++ b/drivers/spi/stm32_qspi.c
@@ -0,0 +1,628 @@
+/*
+ * (C) Copyright 2016
+ *
+ * Michael Kurz, <michi.kurz at gmail.com>
+ *
+ * STM32 QSPI driver
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <spi.h>
+#include <spi_flash.h>
+#include <asm/io.h>
+#include <dm.h>
+#include <errno.h>
+#include <asm/arch/stm32.h>
+#include <asm/arch/stm32_defs.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct stm32_qspi_regs {
+ u32 cr; /* 0x00 */
+ u32 dcr; /* 0x04 */
+ u32 sr; /* 0x08 */
+ u32 fcr; /* 0x0C */
+ u32 dlr; /* 0x10 */
+ u32 ccr; /* 0x14 */
+ u32 ar; /* 0x18 */
+ u32 abr; /* 0x1C */
+ u32 dr; /* 0x20 */
+ u32 psmkr; /* 0x24 */
+ u32 psmar; /* 0x28 */
+ u32 pir; /* 0x2C */
+ u32 lptr; /* 0x30 */
+};
+
+/*
+ * QUADSPI control register
+ */
+#define STM32_QSPI_CR_EN BIT(0)
+#define STM32_QSPI_CR_ABORT BIT(1)
+#define STM32_QSPI_CR_DMAEN BIT(2)
+#define STM32_QSPI_CR_TCEN BIT(3)
+#define STM32_QSPI_CR_SSHIFT BIT(4)
+#define STM32_QSPI_CR_DFM BIT(6)
+#define STM32_QSPI_CR_FSEL BIT(7)
+#define STM32_QSPI_CR_FTHRES_MASK GENMASK(4, 0)
+#define STM32_QSPI_CR_FTHRES_SHIFT (8)
+#define STM32_QSPI_CR_TEIE BIT(16)
+#define STM32_QSPI_CR_TCIE BIT(17)
+#define STM32_QSPI_CR_FTIE BIT(18)
+#define STM32_QSPI_CR_SMIE BIT(19)
+#define STM32_QSPI_CR_TOIE BIT(20)
+#define STM32_QSPI_CR_APMS BIT(22)
+#define STM32_QSPI_CR_PMM BIT(23)
+#define STM32_QSPI_CR_PRESCALER_MASK GENMASK(7, 0)
+#define STM32_QSPI_CR_PRESCALER_SHIFT (24)
+
+/*
+ * QUADSPI device configuration register
+ */
+#define STM32_QSPI_DCR_CKMODE BIT(0)
+#define STM32_QSPI_DCR_CSHT_MASK GENMASK(2, 0)
+#define STM32_QSPI_DCR_CSHT_SHIFT (8)
+#define STM32_QSPI_DCR_FSIZE_MASK GENMASK(4, 0)
+#define STM32_QSPI_DCR_FSIZE_SHIFT (16)
+
+/*
+ * QUADSPI status register
+ */
+#define STM32_QSPI_SR_TEF BIT(0)
+#define STM32_QSPI_SR_TCF BIT(1)
+#define STM32_QSPI_SR_FTF BIT(2)
+#define STM32_QSPI_SR_SMF BIT(3)
+#define STM32_QSPI_SR_TOF BIT(4)
+#define STM32_QSPI_SR_BUSY BIT(5)
+#define STM32_QSPI_SR_FLEVEL_MASK GENMASK(5, 0)
+#define STM32_QSPI_SR_FLEVEL_SHIFT (8)
+
+/*
+ * QUADSPI flag clear register
+ */
+#define STM32_QSPI_FCR_CTEF BIT(0)
+#define STM32_QSPI_FCR_CTCF BIT(1)
+#define STM32_QSPI_FCR_CSMF BIT(3)
+#define STM32_QSPI_FCR_CTOF BIT(4)
+
+/*
+ * QUADSPI communication configuration register
+ */
+#define STM32_QSPI_CCR_DDRM BIT(31)
+#define STM32_QSPI_CCR_DHHC BIT(30)
+#define STM32_QSPI_CCR_SIOO BIT(28)
+#define STM32_QSPI_CCR_FMODE_SHIFT (26)
+#define STM32_QSPI_CCR_DMODE_SHIFT (24)
+#define STM32_QSPI_CCR_DCYC_SHIFT (18)
+#define STM32_QSPI_CCR_DCYC_MASK GENMASK(4, 0)
+#define STM32_QSPI_CCR_ABSIZE_SHIFT (16)
+#define STM32_QSPI_CCR_ABMODE_SHIFT (14)
+#define STM32_QSPI_CCR_ADSIZE_SHIFT (12)
+#define STM32_QSPI_CCR_ADMODE_SHIFT (10)
+#define STM32_QSPI_CCR_IMODE_SHIFT (8)
+#define STM32_QSPI_CCR_INSTRUCTION_MASK GENMASK(7, 0)
+
+enum STM32_QSPI_CCR_IMODE {
+ STM32_QSPI_CCR_IMODE_NONE = 0,
+ STM32_QSPI_CCR_IMODE_ONE_LINE = 1,
+ STM32_QSPI_CCR_IMODE_TWO_LINE = 2,
+ STM32_QSPI_CCR_IMODE_FOUR_LINE = 3,
+};
+
+enum STM32_QSPI_CCR_ADMODE {
+ STM32_QSPI_CCR_ADMODE_NONE = 0,
+ STM32_QSPI_CCR_ADMODE_ONE_LINE = 1,
+ STM32_QSPI_CCR_ADMODE_TWO_LINE = 2,
+ STM32_QSPI_CCR_ADMODE_FOUR_LINE = 3,
+};
+
+enum STM32_QSPI_CCR_ADSIZE {
+ STM32_QSPI_CCR_ADSIZE_8BIT = 0,
+ STM32_QSPI_CCR_ADSIZE_16BIT = 1,
+ STM32_QSPI_CCR_ADSIZE_24BIT = 2,
+ STM32_QSPI_CCR_ADSIZE_32BIT = 3,
+};
+
+enum STM32_QSPI_CCR_ABMODE {
+ STM32_QSPI_CCR_ABMODE_NONE = 0,
+ STM32_QSPI_CCR_ABMODE_ONE_LINE = 1,
+ STM32_QSPI_CCR_ABMODE_TWO_LINE = 2,
+ STM32_QSPI_CCR_ABMODE_FOUR_LINE = 3,
+};
+
+enum STM32_QSPI_CCR_ABSIZE {
+ STM32_QSPI_CCR_ABSIZE_8BIT = 0,
+ STM32_QSPI_CCR_ABSIZE_16BIT = 1,
+ STM32_QSPI_CCR_ABSIZE_24BIT = 2,
+ STM32_QSPI_CCR_ABSIZE_32BIT = 3,
+};
+
+enum STM32_QSPI_CCR_DMODE {
+ STM32_QSPI_CCR_DMODE_NONE = 0,
+ STM32_QSPI_CCR_DMODE_ONE_LINE = 1,
+ STM32_QSPI_CCR_DMODE_TWO_LINE = 2,
+ STM32_QSPI_CCR_DMODE_FOUR_LINE = 3,
+};
+
+enum STM32_QSPI_CCR_FMODE {
+ STM32_QSPI_CCR_IND_WRITE = 0,
+ STM32_QSPI_CCR_IND_READ = 1,
+ STM32_QSPI_CCR_AUTO_POLL = 2,
+ STM32_QSPI_CCR_MEM_MAP = 3,
+};
+
+/* default SCK frequency, unit: HZ */
+#define STM32_QSPI_DEFAULT_SCK_FREQ 108000000
+
+struct stm32_qspi_platdata {
+ u32 base;
+ u32 memory_map;
+ u32 max_hz;
+};
+
+struct stm32_qspi_priv {
+ struct stm32_qspi_regs *regs;
+ u32 max_hz;
+ u32 mode;
+
+ u32 command;
+ u32 address;
+ u32 dummycycles;
+#define CMD_HAS_ADR BIT(24)
+#define CMD_HAS_DUMMY BIT(25)
+#define CMD_HAS_DATA BIT(26)
+};
+
+static void _stm32_qspi_disable(struct stm32_qspi_priv *priv)
+{
+ clrbits_le32(&priv->regs->cr, STM32_QSPI_CR_EN);
+}
+
+static void _stm32_qspi_enable(struct stm32_qspi_priv *priv)
+{
+ setbits_le32(&priv->regs->cr, STM32_QSPI_CR_EN);
+}
+
+static void _stm32_qspi_wait_for_not_busy(struct stm32_qspi_priv *priv)
+{
+ while (readl(&priv->regs->sr) & STM32_QSPI_SR_BUSY)
+ ;
+}
+
+static void _stm32_qspi_wait_for_complete(struct stm32_qspi_priv *priv)
+{
+ while (!(readl(&priv->regs->sr) & STM32_QSPI_SR_TCF))
+ ;
+}
+
+static void _stm32_qspi_wait_for_ftf(struct stm32_qspi_priv *priv)
+{
+ while (!(readl(&priv->regs->sr) & STM32_QSPI_SR_FTF))
+ ;
+}
+
+static void _stm32_qspi_set_flash_size(struct stm32_qspi_priv *priv, u32 size)
+{
+ u32 fsize = fls(size) - 1;
+ clrsetbits_le32(&priv->regs->dcr,
+ STM32_QSPI_DCR_FSIZE_MASK << STM32_QSPI_DCR_FSIZE_SHIFT,
+ fsize << STM32_QSPI_DCR_FSIZE_SHIFT);
+}
+
+static unsigned int _stm32_qspi_gen_ccr(struct stm32_qspi_priv *priv)
+{
+ unsigned int ccr_reg = 0;
+ u8 imode, admode, dmode;
+ u32 mode = priv->mode;
+ u32 cmd = (priv->command & STM32_QSPI_CCR_INSTRUCTION_MASK);
+
+ imode = STM32_QSPI_CCR_IMODE_ONE_LINE;
+ admode = STM32_QSPI_CCR_ADMODE_ONE_LINE;
+
+ if (mode & SPI_RX_QUAD) {
+ dmode = STM32_QSPI_CCR_DMODE_FOUR_LINE;
+ if (mode & SPI_TX_QUAD) {
+ imode = STM32_QSPI_CCR_IMODE_FOUR_LINE;
+ admode = STM32_QSPI_CCR_ADMODE_FOUR_LINE;
+ }
+ } else if (mode & SPI_RX_DUAL) {
+ dmode = STM32_QSPI_CCR_DMODE_TWO_LINE;
+ if (mode & SPI_TX_DUAL) {
+ imode = STM32_QSPI_CCR_IMODE_TWO_LINE;
+ admode = STM32_QSPI_CCR_ADMODE_TWO_LINE;
+ }
+ } else {
+ dmode = STM32_QSPI_CCR_DMODE_ONE_LINE;
+ }
+
+ if (priv->command & CMD_HAS_DATA)
+ ccr_reg |= (dmode << STM32_QSPI_CCR_DMODE_SHIFT);
+
+ if (priv->command & CMD_HAS_DUMMY)
+ ccr_reg |= ((priv->dummycycles & STM32_QSPI_CCR_DCYC_MASK)
+ << STM32_QSPI_CCR_DCYC_SHIFT);
+
+ if (priv->command & CMD_HAS_ADR) {
+ ccr_reg |= (STM32_QSPI_CCR_ADSIZE_24BIT
+ << STM32_QSPI_CCR_ADSIZE_SHIFT);
+ ccr_reg |= (admode << STM32_QSPI_CCR_ADMODE_SHIFT);
+ }
+ ccr_reg |= (imode << STM32_QSPI_CCR_IMODE_SHIFT);
+ ccr_reg |= cmd;
+ return ccr_reg;
+}
+
+static void _stm32_qspi_enable_mmap(struct stm32_qspi_priv *priv,
+ struct spi_flash *flash)
+{
+ priv->command = flash->read_cmd | CMD_HAS_ADR | CMD_HAS_DATA
+ | CMD_HAS_DUMMY;
+ priv->dummycycles = flash->dummy_byte * 8;
+
+ unsigned int ccr_reg = _stm32_qspi_gen_ccr(priv);
+ ccr_reg |= (STM32_QSPI_CCR_MEM_MAP << STM32_QSPI_CCR_FMODE_SHIFT);
+
+ _stm32_qspi_wait_for_not_busy(priv);
+
+ writel(ccr_reg, &priv->regs->ccr);
+
+ priv->dummycycles = 0;
+}
+
+static void _stm32_qspi_disable_mmap(struct stm32_qspi_priv *priv)
+{
+ setbits_le32(&priv->regs->cr, STM32_QSPI_CR_ABORT);
+}
+
+static void _stm32_qspi_set_xfer_length(struct stm32_qspi_priv *priv,
+ u32 length)
+{
+ writel(length - 1, &priv->regs->dlr);
+}
+
+static void _stm32_qspi_start_xfer(struct stm32_qspi_priv *priv, u32 cr_reg)
+{
+ writel(cr_reg, &priv->regs->ccr);
+
+ if (priv->command & CMD_HAS_ADR)
+ writel(priv->address, &priv->regs->ar);
+}
+
+static int _stm32_qspi_xfer(struct stm32_qspi_priv *priv,
+ struct spi_flash *flash, unsigned int bitlen,
+ const u8 *dout, u8 *din, unsigned long flags)
+{
+ unsigned int words = bitlen / 8;
+
+ if (flags & SPI_XFER_MMAP) {
+ _stm32_qspi_enable_mmap(priv, flash);
+ return 0;
+ } else if (flags & SPI_XFER_MMAP_END) {
+ _stm32_qspi_disable_mmap(priv);
+ return 0;
+ }
+
+ if (bitlen == 0)
+ return -1;
+
+ if (bitlen % 8) {
+ debug("spi_xfer: Non byte aligned SPI transfer\n");
+ return -1;
+ }
+
+ if (dout && din) {
+ debug("spi_xfer: QSPI cannot have data in and data out set\n");
+ return -1;
+ }
+
+ if (!dout && (flags & SPI_XFER_BEGIN)) {
+ debug("spi_xfer: QSPI transfer must begin with command\n");
+ return -1;
+ }
+
+ if (dout) {
+ if (flags & SPI_XFER_BEGIN) {
+ /* data is command */
+ priv->command = dout[0] | CMD_HAS_DATA;
+ if (words >= 4) {
+ /* address is here too */
+ priv->address = (dout[1] << 16) |
+ (dout[2] << 8) | dout[3];
+ priv->command |= CMD_HAS_ADR;
+ }
+
+ if (words > 4) {
+ /* rest is dummy bytes */
+ priv->dummycycles = (words - 4) * 8;
+ priv->command |= CMD_HAS_DUMMY;
+ }
+
+ if (flags & SPI_XFER_END) {
+ /* command without data */
+ priv->command &= ~(CMD_HAS_DATA);
+ }
+ }
+
+ if (flags & SPI_XFER_END) {
+ u32 ccr_reg = _stm32_qspi_gen_ccr(priv);
+ ccr_reg |= STM32_QSPI_CCR_IND_WRITE
+ << STM32_QSPI_CCR_FMODE_SHIFT;
+
+ _stm32_qspi_wait_for_not_busy(priv);
+
+ if (priv->command & CMD_HAS_DATA)
+ _stm32_qspi_set_xfer_length(priv, words);
+
+ _stm32_qspi_start_xfer(priv, ccr_reg);
+
+ debug("%s: write: ccr:0x%08x adr:0x%08x\n",
+ __func__, priv->regs->ccr, priv->regs->ar);
+
+ if (priv->command & CMD_HAS_DATA) {
+ _stm32_qspi_wait_for_ftf(priv);
+
+ debug("%s: words:%d data:", __func__, words);
+
+ int i = 0;
+ while (words > i) {
+ writeb(dout[i], &priv->regs->dr);
+ debug("%02x ", dout[i]);
+ i++;
+ }
+ debug("\n");
+
+ _stm32_qspi_wait_for_complete(priv);
+ } else {
+ _stm32_qspi_wait_for_not_busy(priv);
+ }
+ }
+ } else if (din) {
+ u32 ccr_reg = _stm32_qspi_gen_ccr(priv);
+ ccr_reg |= STM32_QSPI_CCR_IND_READ
+ << STM32_QSPI_CCR_FMODE_SHIFT;
+
+ _stm32_qspi_wait_for_not_busy(priv);
+
+ _stm32_qspi_set_xfer_length(priv, words);
+
+ _stm32_qspi_start_xfer(priv, ccr_reg);
+
+ debug("%s: read: ccr:0x%08x adr:0x%08x len:%d\n", __func__,
+ priv->regs->ccr, priv->regs->ar, priv->regs->dlr);
+
+ debug("%s: data:", __func__);
+
+ int i = 0;
+ while (words > i) {
+ din[i] = readb(&priv->regs->dr);
+ debug("%02x ", din[i]);
+ i++;
+ }
+ debug("\n");
+ }
+
+ return 0;
+}
+
+static int stm32_qspi_ofdata_to_platdata(struct udevice *bus)
+{
+ struct fdt_resource res_regs, res_mem;
+ struct stm32_qspi_platdata *plat = bus->platdata;
+ const void *blob = gd->fdt_blob;
+ int node = bus->of_offset;
+ int ret;
+
+ ret = fdt_get_named_resource(blob, node, "reg", "reg-names",
+ "QuadSPI", &res_regs);
+ if (ret) {
+ debug("Error: can't get regs base addresses(ret = %d)!\n", ret);
+ return -ENOMEM;
+ }
+ ret = fdt_get_named_resource(blob, node, "reg", "reg-names",
+ "QuadSPI-memory", &res_mem);
+ if (ret) {
+ debug("Error: can't get mmap base address(ret = %d)!\n", ret);
+ return -ENOMEM;
+ }
+
+ plat->max_hz = fdtdec_get_int(blob, node, "spi-max-frequency",
+ STM32_QSPI_DEFAULT_SCK_FREQ);
+
+ plat->base = res_regs.start;
+ plat->memory_map = res_mem.start;
+
+ debug("%s: regs=<0x%x> mapped=<0x%x>, max-frequency=%d\n",
+ __func__,
+ plat->base,
+ plat->memory_map,
+ plat->max_hz
+ );
+
+ return 0;
+}
+
+static int stm32_qspi_probe(struct udevice *bus)
+{
+ struct stm32_qspi_platdata *plat = dev_get_platdata(bus);
+ struct stm32_qspi_priv *priv = dev_get_priv(bus);
+ struct dm_spi_bus *dm_spi_bus;
+
+ dm_spi_bus = bus->uclass_priv;
+
+ dm_spi_bus->max_hz = plat->max_hz;
+
+ priv->regs = (struct stm32_qspi_regs *)(uintptr_t)plat->base;
+
+ priv->max_hz = plat->max_hz;
+
+ clock_setup(QSPI_CLOCK_CFG);
+
+ setbits_le32(&priv->regs->cr, STM32_QSPI_CR_SSHIFT);
+
+ return 0;
+}
+
+static int stm32_qspi_remove(struct udevice *bus)
+{
+ return 0;
+}
+
+static int stm32_qspi_claim_bus(struct udevice *dev)
+{
+ struct stm32_qspi_priv *priv;
+ struct udevice *bus;
+ struct spi_flash *flash;
+
+ bus = dev->parent;
+ priv = dev_get_priv(bus);
+ flash = dev_get_uclass_priv(dev);
+
+ _stm32_qspi_set_flash_size(priv, flash->size);
+
+ _stm32_qspi_enable(priv);
+
+ return 0;
+}
+
+static int stm32_qspi_release_bus(struct udevice *dev)
+{
+ struct stm32_qspi_priv *priv;
+ struct udevice *bus;
+
+ bus = dev->parent;
+ priv = dev_get_priv(bus);
+
+ _stm32_qspi_disable(priv);
+
+ return 0;
+}
+
+static int stm32_qspi_xfer(struct udevice *dev, unsigned int bitlen,
+ const void *dout, void *din, unsigned long flags)
+{
+ struct stm32_qspi_priv *priv;
+ struct udevice *bus;
+ struct spi_flash *flash;
+
+ bus = dev->parent;
+ priv = dev_get_priv(bus);
+ flash = dev_get_uclass_priv(dev);
+
+ return _stm32_qspi_xfer(priv, flash, bitlen, (const u8 *)dout,
+ (u8 *)din, flags);
+}
+
+static int stm32_qspi_set_speed(struct udevice *bus, uint speed)
+{
+ struct stm32_qspi_platdata *plat = bus->platdata;
+ struct stm32_qspi_priv *priv = dev_get_priv(bus);
+
+ if (speed > plat->max_hz)
+ speed = plat->max_hz;
+
+ u32 qspi_clk = clock_get(CLOCK_AHB);
+ u32 prescaler = 255;
+ if (speed > 0) {
+ prescaler = DIV_ROUND_UP(qspi_clk, speed) - 1;
+ if (prescaler > 255)
+ prescaler = 255;
+ else if (prescaler < 0)
+ prescaler = 0;
+ }
+
+ u32 csht = DIV_ROUND_UP((5 * qspi_clk) / (prescaler + 1), 100000000);
+ csht = (csht - 1) & STM32_QSPI_DCR_CSHT_MASK;
+
+ _stm32_qspi_wait_for_not_busy(priv);
+
+ clrsetbits_le32(&priv->regs->cr,
+ STM32_QSPI_CR_PRESCALER_MASK <<
+ STM32_QSPI_CR_PRESCALER_SHIFT,
+ prescaler << STM32_QSPI_CR_PRESCALER_SHIFT);
+
+
+ clrsetbits_le32(&priv->regs->dcr,
+ STM32_QSPI_DCR_CSHT_MASK << STM32_QSPI_DCR_CSHT_SHIFT,
+ csht << STM32_QSPI_DCR_CSHT_SHIFT);
+
+ debug("%s: regs=%p, speed=%d\n", __func__, priv->regs,
+ (qspi_clk / (prescaler + 1)));
+
+ return 0;
+}
+
+static int stm32_qspi_set_mode(struct udevice *bus, uint mode)
+{
+ struct stm32_qspi_priv *priv = dev_get_priv(bus);
+
+ _stm32_qspi_wait_for_not_busy(priv);
+
+ if ((mode & SPI_CPHA) && (mode & SPI_CPOL))
+ setbits_le32(&priv->regs->dcr, STM32_QSPI_DCR_CKMODE);
+ else if (!(mode & SPI_CPHA) && !(mode & SPI_CPOL))
+ clrbits_le32(&priv->regs->dcr, STM32_QSPI_DCR_CKMODE);
+ else
+ return -ENODEV;
+
+ if (mode & SPI_CS_HIGH)
+ return -ENODEV;
+
+ if (mode & SPI_RX_QUAD)
+ priv->mode |= SPI_RX_QUAD;
+ else if (mode & SPI_RX_DUAL)
+ priv->mode |= SPI_RX_DUAL;
+ else
+ priv->mode &= ~(SPI_RX_QUAD | SPI_RX_DUAL);
+
+ if (mode & SPI_TX_QUAD)
+ priv->mode |= SPI_TX_QUAD;
+ else if (mode & SPI_TX_DUAL)
+ priv->mode |= SPI_TX_DUAL;
+ else
+ priv->mode &= ~(SPI_TX_QUAD | SPI_TX_DUAL);
+
+ debug("%s: regs=%p, mode=%d rx: ", __func__, priv->regs, mode);
+
+ if (mode & SPI_RX_QUAD)
+ debug("quad, tx: ");
+ else if (mode & SPI_RX_DUAL)
+ debug("dual, tx: ");
+ else
+ debug("single, tx: ");
+
+ if (mode & SPI_TX_QUAD)
+ debug("quad\n");
+ else if (mode & SPI_TX_DUAL)
+ debug("dual\n");
+ else
+ debug("single\n");
+
+ return 0;
+}
+
+static const struct dm_spi_ops stm32_qspi_ops = {
+ .claim_bus = stm32_qspi_claim_bus,
+ .release_bus = stm32_qspi_release_bus,
+ .xfer = stm32_qspi_xfer,
+ .set_speed = stm32_qspi_set_speed,
+ .set_mode = stm32_qspi_set_mode,
+};
+
+static const struct udevice_id stm32_qspi_ids[] = {
+ { .compatible = "st,stm32-qspi" },
+ { }
+};
+
+U_BOOT_DRIVER(stm32_qspi) = {
+ .name = "stm32_qspi",
+ .id = UCLASS_SPI,
+ .of_match = stm32_qspi_ids,
+ .ops = &stm32_qspi_ops,
+ .ofdata_to_platdata = stm32_qspi_ofdata_to_platdata,
+ .platdata_auto_alloc_size = sizeof(struct stm32_qspi_platdata),
+ .priv_auto_alloc_size = sizeof(struct stm32_qspi_priv),
+ .probe = stm32_qspi_probe,
+ .remove = stm32_qspi_remove,
+};
--
2.1.4
More information about the U-Boot
mailing list