[U-Boot] [PATCH v2 8/8] spi: cadence_qspi: Support specifying the sample edge used

[Phil Edworthy]

Whilst at it, move the code to read the "sram-size" property
into the other code that reads properties from the node, rather
than the SF subnode.

Also change the code to use a bool for the bypass arg.

Signed-off-by: Phil Edworthy <phil.edworthy at renesas.com>

---
v2:
 Change name of DT prop and provide details of what it does.
 Whilst at it, move the code to read the "sram-size" property
 into the other code that reads properties from the node, rather
 than the SF subnode.

 Also change the code to use a bool for the bypass arg.
---
 doc/device-tree-bindings/spi/spi-cadence.txt |  2 ++
 drivers/spi/cadence_qspi.c                   | 13 +++++++++----
 drivers/spi/cadence_qspi.h                   |  3 ++-
 drivers/spi/cadence_qspi_apb.c               |  8 +++++++-
 4 files changed, 20 insertions(+), 6 deletions(-)

diff --git a/doc/device-tree-bindings/spi/spi-cadence.txt b/doc/device-tree-bindings/spi/spi-cadence.txt
index c1e2233..94c800b 100644
--- a/doc/device-tree-bindings/spi/spi-cadence.txt
+++ b/doc/device-tree-bindings/spi/spi-cadence.txt
@@ -26,3 +26,5 @@ connected flash properties
 			  select (n_ss_out).
 - tslch-ns		: Delay in master reference clocks between setting
 			  n_ss_out low and first bit transfer
+- sample-edge-rising	: Data outputs from flash memory will be sampled on the
+			  rising edge. Default is falling edge.
diff --git a/drivers/spi/cadence_qspi.c b/drivers/spi/cadence_qspi.c
index 1051afb..16fb18e 100644
--- a/drivers/spi/cadence_qspi.c
+++ b/drivers/spi/cadence_qspi.c
@@ -39,8 +39,10 @@ static int cadence_spi_write_speed(struct udevice *bus, uint hz)
 /* Calibration sequence to determine the read data capture delay register */
 static int spi_calibration(struct udevice *bus, uint hz)
 {
+	struct cadence_spi_platdata *plat = bus->platdata;
 	struct cadence_spi_priv *priv = dev_get_priv(bus);
 	void *base = priv->regbase;
+	bool edge = plat->sample_edge_rising;
 	u8 opcode_rdid = 0x9F;
 	unsigned int idcode = 0, temp = 0;
 	int err = 0, i, range_lo = -1, range_hi = -1;
@@ -49,7 +51,7 @@ static int spi_calibration(struct udevice *bus, uint hz)
 	cadence_spi_write_speed(bus, 1000000);
 
 	/* configure the read data capture delay register to 0 */
-	cadence_qspi_apb_readdata_capture(base, 1, 0);
+	cadence_qspi_apb_readdata_capture(base, true, edge, 0);
 
 	/* Enable QSPI */
 	cadence_qspi_apb_controller_enable(base);
@@ -69,7 +71,7 @@ static int spi_calibration(struct udevice *bus, uint hz)
 		cadence_qspi_apb_controller_disable(base);
 
 		/* reconfigure the read data capture delay register */
-		cadence_qspi_apb_readdata_capture(base, 1, i);
+		cadence_qspi_apb_readdata_capture(base, true, edge, i);
 
 		/* Enable back QSPI */
 		cadence_qspi_apb_controller_enable(base);
@@ -105,7 +107,8 @@ static int spi_calibration(struct udevice *bus, uint hz)
 	cadence_qspi_apb_controller_disable(base);
 
 	/* configure the final value for read data capture delay register */
-	cadence_qspi_apb_readdata_capture(base, 1, (range_hi + range_lo) / 2);
+	cadence_qspi_apb_readdata_capture(base, true, edge,
+		(range_hi + range_lo) / 2);
 	debug("SF: Read data capture delay calibrated to %i (%i - %i)\n",
 	      (range_hi + range_lo) / 2, range_lo, range_hi);
 
@@ -298,6 +301,7 @@ static int cadence_spi_ofdata_to_platdata(struct udevice *bus)
 
 	plat->regbase = (void *)data[0];
 	plat->ahbbase = (void *)data[2];
+	plat->sram_size = fdtdec_get_int(blob, node, "sram-size", 128);
 
 	/* All other paramters are embedded in the child node */
 	subnode = fdt_first_subnode(blob, node);
@@ -317,7 +321,8 @@ static int cadence_spi_ofdata_to_platdata(struct udevice *bus)
 	plat->tsd2d_ns = fdtdec_get_int(blob, subnode, "tsd2d-ns", 255);
 	plat->tchsh_ns = fdtdec_get_int(blob, subnode, "tchsh-ns", 20);
 	plat->tslch_ns = fdtdec_get_int(blob, subnode, "tslch-ns", 20);
-	plat->sram_size = fdtdec_get_int(blob, node, "sram-size", 128);
+	plat->sample_edge_rising = fdtdec_get_bool(blob, subnode,
+		"sample-edge-rising");
 
 	debug("%s: regbase=%p ahbbase=%p max-frequency=%d page-size=%d\n",
 	      __func__, plat->regbase, plat->ahbbase, plat->max_hz,
diff --git a/drivers/spi/cadence_qspi.h b/drivers/spi/cadence_qspi.h
index a849f7b..ad1dbae 100644
--- a/drivers/spi/cadence_qspi.h
+++ b/drivers/spi/cadence_qspi.h
@@ -26,6 +26,7 @@ struct cadence_spi_platdata {
 	u32		tchsh_ns;
 	u32		tslch_ns;
 	u32		sram_size;
+	bool		sample_edge_rising;
 };
 
 struct cadence_spi_priv {
@@ -73,6 +74,6 @@ void cadence_qspi_apb_delay(void *reg_base,
 	unsigned int tchsh_ns, unsigned int tslch_ns);
 void cadence_qspi_apb_enter_xip(void *reg_base, char xip_dummy);
 void cadence_qspi_apb_readdata_capture(void *reg_base,
-	unsigned int bypass, unsigned int delay);
+	bool bypass, bool edge, unsigned int delay);
 
 #endif /* __CADENCE_QSPI_H__ */
diff --git a/drivers/spi/cadence_qspi_apb.c b/drivers/spi/cadence_qspi_apb.c
index 56ad952..e43973c 100644
--- a/drivers/spi/cadence_qspi_apb.c
+++ b/drivers/spi/cadence_qspi_apb.c
@@ -98,6 +98,7 @@
 #define	CQSPI_REG_RD_DATA_CAPTURE_BYPASS	BIT(0)
 #define	CQSPI_REG_RD_DATA_CAPTURE_DELAY_LSB	1
 #define	CQSPI_REG_RD_DATA_CAPTURE_DELAY_MASK	0xF
+#define	CQSPI_REG_RD_DATA_CAPTURE_EDGE		BIT(5)
 
 #define	CQSPI_REG_SIZE				0x14
 #define	CQSPI_REG_SIZE_ADDRESS_LSB		0
@@ -234,7 +235,7 @@ static unsigned int cadence_qspi_wait_idle(void *reg_base)
 }
 
 void cadence_qspi_apb_readdata_capture(void *reg_base,
-				unsigned int bypass, unsigned int delay)
+	bool bypass, bool edge, unsigned int delay)
 {
 	unsigned int reg;
 	cadence_qspi_apb_controller_disable(reg_base);
@@ -246,6 +247,11 @@ void cadence_qspi_apb_readdata_capture(void *reg_base,
 	else
 		reg &= ~CQSPI_REG_RD_DATA_CAPTURE_BYPASS;
 
+	if (edge)
+		reg |= CQSPI_REG_RD_DATA_CAPTURE_EDGE;
+	else
+		reg &= ~CQSPI_REG_RD_DATA_CAPTURE_EDGE;
+
 	reg &= ~(CQSPI_REG_RD_DATA_CAPTURE_DELAY_MASK
 		<< CQSPI_REG_RD_DATA_CAPTURE_DELAY_LSB);
 
-- 
2.7.4