[U-Boot] [PATCH v2] board/ls2088ardb: set rear fan speed to reduce noise
york sun
york.sun at nxp.com
Wed Nov 30 19:20:50 CET 2016
Ying,
There is no ls2088ardb board. It is ls2080ardb target supporting all
three variants.
On 11/21/2016 05:30 AM, ying.zhang22455 at nxp.com wrote:
> From: Ying Zhang <ying.zhang22455 at nxp.com>
>
> Fan settings(PWM signal set to ~50% duty cycle for all three rear)
> fans provide good thermal air flow with considerable reduction of
> fan noise.
This grammar is wrong in this sentence.
>
> Signed-off-by: Ying Zhang <ying.zhang22455 at nxp.com>
> ---
> [changed from v1]: make the function static.
>
> board/freescale/ls2080ardb/ls2080ardb.c | 31 +++++++++++++++++++++++++++++++
> include/configs/ls2080ardb.h | 6 ++++++
> 2 files changed, 37 insertions(+)
>
> diff --git a/board/freescale/ls2080ardb/ls2080ardb.c b/board/freescale/ls2080ardb/ls2080ardb.c
> index 83d9e7e..bc5dd53 100644
> --- a/board/freescale/ls2080ardb/ls2080ardb.c
> +++ b/board/freescale/ls2080ardb/ls2080ardb.c
> @@ -151,6 +151,36 @@ int config_board_mux(int ctrl_type)
> return 0;
> }
>
> +static void set_fan_speed(void)
> +{
> + int ret, i;
> + u8 value;
> +
> + select_i2c_ch_pca9547(I2C_MUX_CH_FAN);
> + value = 0x80;
What are these values 0x80. 1, 0x20? Can you put some comments here so
others don't have to read through the reference manual of the i2c chip?
> + ret = i2c_write(I2C_FAN_CONTROLLER_ADDR, 0x0, 1, &value, 1);
> + if (ret) {
> + printf("Fan: Failed to set fan speed\n");
> + return;
> + }
> + value = 1;
> + ret = i2c_write(I2C_FAN_CONTROLLER_ADDR, 0x58, 1, &value, 1);
> + if (ret) {
> + printf("Fan: Failed to set fan speed\n");
> + return;
> + }
> +
> + /* set PWM = ~50% DCyc for all rear PWM fans */
> + value = 0x20;
> + for (i = 0xb4; i < 0xb9; i++) {
> + ret = i2c_write(I2C_FAN_CONTROLLER_ADDR, i, 1, &value, 1);
> + if (ret) {
> + printf("Fan: Failed to set fan speed\n");
> + return;
> + }
> + }
Do you want to skip the rest of fans if one fails?
York
> +}
> +
> int board_init(void)
> {
> char *env_hwconfig;
> @@ -175,6 +205,7 @@ int board_init(void)
> #ifdef CONFIG_ENV_IS_NOWHERE
> gd->env_addr = (ulong)&default_environment[0];
> #endif
> + set_fan_speed();
> select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
>
> QIXIS_WRITE(rst_ctl, QIXIS_RST_CTL_RESET_EN);
> diff --git a/include/configs/ls2080ardb.h b/include/configs/ls2080ardb.h
> index b9cb6d3..05f98c0 100644
> --- a/include/configs/ls2080ardb.h
> +++ b/include/configs/ls2080ardb.h
> @@ -264,6 +264,7 @@ unsigned long get_board_sys_clk(void);
>
> /* I2C bus multiplexer */
> #define I2C_MUX_CH_DEFAULT 0x8
> +#define I2C_MUX_CH_FAN 0xd
>
> /* SPI */
> #ifdef CONFIG_FSL_DSPI
> @@ -279,6 +280,11 @@ unsigned long get_board_sys_clk(void);
> #define CONFIG_SYS_I2C_RTC_ADDR 0x68
> #define CONFIG_CMD_DATE
>
> +/*
> + * Winbond fan controller
> + */
> +#define I2C_FAN_CONTROLLER_ADDR 0x2c
> +
> /* EEPROM */
> #define CONFIG_ID_EEPROM
> #define CONFIG_CMD_EEPROM
>
More information about the U-Boot
mailing list