[U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support

Jagan Teki jagan at openedev.com
Mon Oct 17 05:40:46 CEST 2016


Hi Stefano,

On Tue, Oct 11, 2016 at 9:00 AM, Jagan Teki <jteki at openedev.com> wrote:
> Hi Stefano,
>
> On Sun, Oct 9, 2016 at 8:15 PM, Jagan Teki <jagannadh.teki at gmail.com> wrote:
>> Hi Stefano,
>>
>> On Sat, Oct 8, 2016 at 6:00 PM, Jagan Teki <jteki at openedev.com> wrote:
>>> From: Jagan Teki <jagan at amarulasolutions.com>
>>>
>>> This series supports Engicam i.CoreM6 QDL modules on top of u-boot-imx/master
>>> and test on the respective starter kits as well.
>>>
>>> Tested both MMC and NAND boot.
>>>
>>> Changes for v7:
>>>         - Add patch to CONFIG_DEFAULT_FDT_FILE to defconfigs
>>>         - Rebase on u-boot-imx/master
>>>
>>> Changes for v6:
>>>         - Rebase to u-boot-imx/master
>>>         - Move few SPL configs to defconfigs
>>>
>>> Changes for v5:
>>>         - Add NAND support
>>>
>>> Changes for v4:
>>>         - Add 'net: Kconfig: Add FEC_MXC entry' patch
>>>         - Updated ENV configs along with comments
>>>         - Restructured configs for more readability
>>>         - Add CONFIG_ENV_OVERWRITE
>>>         - Rename icorem6qdl_defconfig with icorem6qdl_mmc_defconfig
>>>
>>> Changes for v3:
>>>         - Remove "v2 01/17 imx: iomux-v3: Fix build error with snvs base" patch
>>>         - Remove 'default n' on Kconfig DEFAULT_FDT_FILE patch
>>>         - Add minimal devicetree support for Engicam i.CoreM6 QDL
>>>         - Add is_mx6dl()
>>>         - Add is_mx6solo()
>>>         - Use is_mx6dq()
>>>         - Add last commit sha1 and header in pull devicetree files from Linux
>>>
>>> Changes for v2:
>>>         - Make static to local iomux structure in board file
>>>         - Corrected rowaddr in mx6_ddr3_cfg
>>>         - Used imx_ddr_size
>>>         - Add FEC support and tested the same
>>>         - Add DM_GPIO, DM_MMC support
>>>         - Add pinctrl support
>>>         - Add devicetree support
>>>
>>> Jagan Teki (21):
>>>   serial: Kconfig: Add MXC_UART entry
>>>   thermal: Kconfig: Add IMX_THERMAL entry
>>>   config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs
>>>   arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support
>>>   net: Kconfig: Add FEC_MXC entry
>>>   imx6: icorem6: Add ENET support
>>>   imx: s/docs\/README.imximage/doc\/README.imximage/g
>>>   arm: dts: Add devicetree for i.MX6DL
>>>   arm: dts: Add devicetree for i.MX6DQL
>>>   arm: dts: imx6dl: Add pinctrl defines
>>>   dt-bindings: clock: imx6qdl: Add clock defines
>>>   arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
>>>   imx6q: icorem6: Enable pinctrl driver
>>>   engicam: icorem6: Add DM_GPIO, DM_MMC support
>>>   arm: dts: Add devicetree for i.MX6Q
>>>   arm: dts: imx6q: Add pinctrl defines
>>>   arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
>>>   mtd: nand: Kconfig: Add NAND_MXS entry
>>>   imx6: icorem6: Add NAND support
>>>   imx6: icorem6: Enable MTD device support
>>>   imx6: icorem6: Add default mtd nand partition table
>>
>> All set now, please do apply.
>
> Let me know if you still find any issues, otherwise apply this.
>

Any help?

thanks!
-- 
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.


More information about the U-Boot mailing list