[U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support

Stefano Babic sbabic at denx.de
Mon Oct 17 07:56:26 CEST 2016


Hi Jagan,

On 17/10/2016 05:40, Jagan Teki wrote:
> Hi Stefano,
> 
> On Tue, Oct 11, 2016 at 9:00 AM, Jagan Teki <jteki at openedev.com> wrote:
>> Hi Stefano,
>>
>> On Sun, Oct 9, 2016 at 8:15 PM, Jagan Teki <jagannadh.teki at gmail.com> wrote:
>>> Hi Stefano,
>>>
>>> On Sat, Oct 8, 2016 at 6:00 PM, Jagan Teki <jteki at openedev.com> wrote:
>>>> From: Jagan Teki <jagan at amarulasolutions.com>
>>>>
>>>> This series supports Engicam i.CoreM6 QDL modules on top of u-boot-imx/master
>>>> and test on the respective starter kits as well.
>>>>
>>>> Tested both MMC and NAND boot.
>>>>
>>>> Changes for v7:
>>>>         - Add patch to CONFIG_DEFAULT_FDT_FILE to defconfigs
>>>>         - Rebase on u-boot-imx/master
>>>>
>>>> Changes for v6:
>>>>         - Rebase to u-boot-imx/master
>>>>         - Move few SPL configs to defconfigs
>>>>
>>>> Changes for v5:
>>>>         - Add NAND support
>>>>
>>>> Changes for v4:
>>>>         - Add 'net: Kconfig: Add FEC_MXC entry' patch
>>>>         - Updated ENV configs along with comments
>>>>         - Restructured configs for more readability
>>>>         - Add CONFIG_ENV_OVERWRITE
>>>>         - Rename icorem6qdl_defconfig with icorem6qdl_mmc_defconfig
>>>>
>>>> Changes for v3:
>>>>         - Remove "v2 01/17 imx: iomux-v3: Fix build error with snvs base" patch
>>>>         - Remove 'default n' on Kconfig DEFAULT_FDT_FILE patch
>>>>         - Add minimal devicetree support for Engicam i.CoreM6 QDL
>>>>         - Add is_mx6dl()
>>>>         - Add is_mx6solo()
>>>>         - Use is_mx6dq()
>>>>         - Add last commit sha1 and header in pull devicetree files from Linux
>>>>
>>>> Changes for v2:
>>>>         - Make static to local iomux structure in board file
>>>>         - Corrected rowaddr in mx6_ddr3_cfg
>>>>         - Used imx_ddr_size
>>>>         - Add FEC support and tested the same
>>>>         - Add DM_GPIO, DM_MMC support
>>>>         - Add pinctrl support
>>>>         - Add devicetree support
>>>>
>>>> Jagan Teki (21):
>>>>   serial: Kconfig: Add MXC_UART entry
>>>>   thermal: Kconfig: Add IMX_THERMAL entry
>>>>   config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs
>>>>   arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support
>>>>   net: Kconfig: Add FEC_MXC entry
>>>>   imx6: icorem6: Add ENET support
>>>>   imx: s/docs\/README.imximage/doc\/README.imximage/g
>>>>   arm: dts: Add devicetree for i.MX6DL
>>>>   arm: dts: Add devicetree for i.MX6DQL
>>>>   arm: dts: imx6dl: Add pinctrl defines
>>>>   dt-bindings: clock: imx6qdl: Add clock defines
>>>>   arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
>>>>   imx6q: icorem6: Enable pinctrl driver
>>>>   engicam: icorem6: Add DM_GPIO, DM_MMC support
>>>>   arm: dts: Add devicetree for i.MX6Q
>>>>   arm: dts: imx6q: Add pinctrl defines
>>>>   arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
>>>>   mtd: nand: Kconfig: Add NAND_MXS entry
>>>>   imx6: icorem6: Add NAND support
>>>>   imx6: icorem6: Enable MTD device support
>>>>   imx6: icorem6: Add default mtd nand partition table
>>>
>>> All set now, please do apply.
>>
>> Let me know if you still find any issues, otherwise apply this.
>>
> 
> Any help?

Sorry, I was last week at ELCE - I will go on with your patches (and the
other ones left pending) this week.

Regards,
Stefano

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================


More information about the U-Boot mailing list