[U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support

Jagan Teki jagan at openedev.com
Mon Oct 24 09:53:04 CEST 2016


Hi Stefano,

On Mon, Oct 17, 2016 at 11:26 AM, Stefano Babic <sbabic at denx.de> wrote:
> Hi Jagan,
>
> On 17/10/2016 05:40, Jagan Teki wrote:
>> Hi Stefano,
>>
>> On Tue, Oct 11, 2016 at 9:00 AM, Jagan Teki <jteki at openedev.com> wrote:
>>> Hi Stefano,
>>>
>>> On Sun, Oct 9, 2016 at 8:15 PM, Jagan Teki <jagannadh.teki at gmail.com> wrote:
>>>> Hi Stefano,
>>>>
>>>> On Sat, Oct 8, 2016 at 6:00 PM, Jagan Teki <jteki at openedev.com> wrote:
>>>>> From: Jagan Teki <jagan at amarulasolutions.com>
>>>>>
>>>>> This series supports Engicam i.CoreM6 QDL modules on top of u-boot-imx/master
>>>>> and test on the respective starter kits as well.
>>>>>
>>>>> Tested both MMC and NAND boot.
>>>>>
>>>>> Changes for v7:
>>>>>         - Add patch to CONFIG_DEFAULT_FDT_FILE to defconfigs
>>>>>         - Rebase on u-boot-imx/master
>>>>>
>>>>> Changes for v6:
>>>>>         - Rebase to u-boot-imx/master
>>>>>         - Move few SPL configs to defconfigs
>>>>>
>>>>> Changes for v5:
>>>>>         - Add NAND support
>>>>>
>>>>> Changes for v4:
>>>>>         - Add 'net: Kconfig: Add FEC_MXC entry' patch
>>>>>         - Updated ENV configs along with comments
>>>>>         - Restructured configs for more readability
>>>>>         - Add CONFIG_ENV_OVERWRITE
>>>>>         - Rename icorem6qdl_defconfig with icorem6qdl_mmc_defconfig
>>>>>
>>>>> Changes for v3:
>>>>>         - Remove "v2 01/17 imx: iomux-v3: Fix build error with snvs base" patch
>>>>>         - Remove 'default n' on Kconfig DEFAULT_FDT_FILE patch
>>>>>         - Add minimal devicetree support for Engicam i.CoreM6 QDL
>>>>>         - Add is_mx6dl()
>>>>>         - Add is_mx6solo()
>>>>>         - Use is_mx6dq()
>>>>>         - Add last commit sha1 and header in pull devicetree files from Linux
>>>>>
>>>>> Changes for v2:
>>>>>         - Make static to local iomux structure in board file
>>>>>         - Corrected rowaddr in mx6_ddr3_cfg
>>>>>         - Used imx_ddr_size
>>>>>         - Add FEC support and tested the same
>>>>>         - Add DM_GPIO, DM_MMC support
>>>>>         - Add pinctrl support
>>>>>         - Add devicetree support
>>>>>
>>>>> Jagan Teki (21):
>>>>>   serial: Kconfig: Add MXC_UART entry
>>>>>   thermal: Kconfig: Add IMX_THERMAL entry
>>>>>   config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs
>>>>>   arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support
>>>>>   net: Kconfig: Add FEC_MXC entry
>>>>>   imx6: icorem6: Add ENET support
>>>>>   imx: s/docs\/README.imximage/doc\/README.imximage/g
>>>>>   arm: dts: Add devicetree for i.MX6DL
>>>>>   arm: dts: Add devicetree for i.MX6DQL
>>>>>   arm: dts: imx6dl: Add pinctrl defines
>>>>>   dt-bindings: clock: imx6qdl: Add clock defines
>>>>>   arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
>>>>>   imx6q: icorem6: Enable pinctrl driver
>>>>>   engicam: icorem6: Add DM_GPIO, DM_MMC support
>>>>>   arm: dts: Add devicetree for i.MX6Q
>>>>>   arm: dts: imx6q: Add pinctrl defines
>>>>>   arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
>>>>>   mtd: nand: Kconfig: Add NAND_MXS entry
>>>>>   imx6: icorem6: Add NAND support
>>>>>   imx6: icorem6: Enable MTD device support
>>>>>   imx6: icorem6: Add default mtd nand partition table
>>>>
>>>> All set now, please do apply.
>>>
>>> Let me know if you still find any issues, otherwise apply this.
>>>
>>
>> Any help?
>
> Sorry, I was last week at ELCE - I will go on with your patches (and the
> other ones left pending) this week.

Please apply this, I need to rebase on top of tom/master and send few
more series.

thanks!
-- 
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.


More information about the U-Boot mailing list