[U-Boot] [PATCH v2 1/2] board: ls1043ardb: move sec_init to board_init

[Sumit Garg]

sec_init() which was earlier called in misc_init_r()
is now done in board_init() before PPA init as SEC
block will be used during PPA image validation.

Signed-off-by: Aneesh Bansal <aneesh.bansal at nxp.com>
Signed-off-by: Sumit Garg <sumit.garg at nxp.com>
---

Changes in v2:
Rebased Aneesh's patchset. No dependency.
Link to patchset: https://patchwork.ozlabs.org/patch/586783/

 board/freescale/ls1043ardb/ls1043ardb.c | 32 +++++++++++++++++---------------
 1 file changed, 17 insertions(+), 15 deletions(-)

diff --git a/board/freescale/ls1043ardb/ls1043ardb.c b/board/freescale/ls1043ardb/ls1043ardb.c
index d3e37b4..70fef79 100644
--- a/board/freescale/ls1043ardb/ls1043ardb.c
+++ b/board/freescale/ls1043ardb/ls1043ardb.c
@@ -94,6 +94,23 @@ int board_init(void)
 	enable_layerscape_ns_access();
 #endif
 
+#ifdef CONFIG_SECURE_BOOT
+	/* In case of Secure Boot, the IBR configures the SMMU
+	 * to allow only Secure transactions.
+	 * SMMU must be reset in bypass mode.
+	 * Set the ClientPD bit and Clear the USFCFG Bit
+	 */
+	u32 val;
+	val = (in_le32(SMMU_SCR0) | SCR0_CLIENTPD_MASK) & ~(SCR0_USFCFG_MASK);
+	out_le32(SMMU_SCR0, val);
+	val = (in_le32(SMMU_NSCR0) | SCR0_CLIENTPD_MASK) & ~(SCR0_USFCFG_MASK);
+	out_le32(SMMU_NSCR0, val);
+#endif
+
+#ifdef CONFIG_FSL_CAAM
+	sec_init();
+#endif
+
 #ifdef CONFIG_FSL_LS_PPA
 	ppa_init();
 #endif
@@ -137,21 +154,6 @@ int config_board_mux(void)
 int misc_init_r(void)
 {
 	config_board_mux();
-#ifdef CONFIG_SECURE_BOOT
-	/* In case of Secure Boot, the IBR configures the SMMU
-	 * to allow only Secure transactions.
-	 * SMMU must be reset in bypass mode.
-	 * Set the ClientPD bit and Clear the USFCFG Bit
-	 */
-	u32 val;
-	val = (in_le32(SMMU_SCR0) | SCR0_CLIENTPD_MASK) & ~(SCR0_USFCFG_MASK);
-	out_le32(SMMU_SCR0, val);
-	val = (in_le32(SMMU_NSCR0) | SCR0_CLIENTPD_MASK) & ~(SCR0_USFCFG_MASK);
-	out_le32(SMMU_NSCR0, val);
-#endif
-#ifdef CONFIG_FSL_CAAM
-	return sec_init();
-#endif
 	return 0;
 }
 #endif
-- 
1.8.1.4