[U-Boot] [PATCH v4 5/5] colibri_t20: fix usb operation and controller order

[Marcel Ziswiler]

Without this patch the following error will be shown:

Colibri T20 # usb start
starting USB...
No controllers found

This patch fixes USB operation and also the controller order as the
CI UDC driver may only be instantiated on the first aka OTG port.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler at toradex.com>
Acked-by: Stephen Warren <swarren at nvidia.com>

---

Changes in v4: None
Changes in v3:
- Add Stephen's ack.

Changes in v2:
- As suggested by Stephen remove last patch 5/5 colibri_t20: enable dfu
  also for nand.

 arch/arm/dts/tegra20-colibri.dts | 45 +++++++++++++++++++++-------------------
 1 file changed, 24 insertions(+), 21 deletions(-)

diff --git a/arch/arm/dts/tegra20-colibri.dts b/arch/arm/dts/tegra20-colibri.dts
index 5b803d9..6bc8c49 100644
--- a/arch/arm/dts/tegra20-colibri.dts
+++ b/arch/arm/dts/tegra20-colibri.dts
@@ -14,10 +14,10 @@
 		i2c0 = "/i2c at 7000d000";
 		i2c1 = "/i2c at 7000c000";
 		i2c2 = "/i2c at 7000c400";
-		usb0 = "/usb at c5008000";
-		usb1 = "/usb at c5000000";
-		usb2 = "/usb at c5004000";
 		sdhci0 = "/sdhci at c8000600";
+		usb0 = "/usb at c5000000";
+		usb1 = "/usb at c5004000"; /* on-module only, for ASIX */
+		usb2 = "/usb at c5008000";
 	};
 
 	host1x at 50000000 {
@@ -43,24 +43,6 @@
 		};
 	};
 
-	usb at c5000000 {
-		statuc = "okay";
-		dr_mode = "otg";
-	};
-
-	usb at c5004000 {
-		statuc = "okay";
-		/* VBUS_LAN */
-		nvidia,phy-reset-gpio = <&gpio TEGRA_GPIO(V, 1) GPIO_ACTIVE_HIGH>;
-		nvidia,vbus-gpio = <&gpio TEGRA_GPIO(BB, 1) GPIO_ACTIVE_HIGH>;
-	};
-
-	usb at c5008000 {
-		statuc = "okay";
-		/* USBH_PEN */
-		nvidia,vbus-gpio = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
-	};
-
 	nand-controller at 70008000 {
 		nvidia,wp-gpios = <&gpio TEGRA_GPIO(S, 0) GPIO_ACTIVE_HIGH>;
 		nvidia,width = <8>;
@@ -101,6 +83,27 @@
 		clock-frequency = <100000>;
 	};
 
+	/* EHCI instance 0: USB1_DP/N -> USBC_P/N */
+	usb at c5000000 {
+		status = "okay";
+		dr_mode = "otg";
+	};
+
+	/* EHCI instance 1: ULPI -> USB3340 -> AX88772B */
+	usb at c5004000 {
+		status = "okay";
+		/* VBUS_LAN */
+		nvidia,phy-reset-gpio = <&gpio TEGRA_GPIO(V, 1) GPIO_ACTIVE_HIGH>;
+		nvidia,vbus-gpio = <&gpio TEGRA_GPIO(BB, 1) GPIO_ACTIVE_HIGH>;
+	};
+
+	/* EHCI instance 2: USB3_DP/N -> USBH_P/N */
+	usb at c5008000 {
+		status = "okay";
+		/* USBH_PEN */
+		nvidia,vbus-gpio = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
+	};
+
 	sdhci at c8000600 {
 		status = "okay";
 		bus-width = <4>;
-- 
2.5.5