[U-Boot] [PATCH 01/15] serial: Add serial_mvebu_a3700 for Armada 3700 SoC
Stefan Roese
sr at denx.de
Fri Sep 16 15:09:33 CEST 2016
The Armada 3700's UART is a simple serial port. It has a 32 bytes
Tx FIFO and a 64 bytes Rx FIFO integrated. This patch adds support
for this UART including the DEBUG UART functions for very early
debug output.
Signed-off-by: Stefan Roese <sr at denx.de>
Cc: Nadav Haklai <nadavh at marvell.com>
Cc: Kostya Porotchkin <kostap at marvell.com>
Cc: Wilson Ding <dingwei at marvell.com>
Cc: Victor Gu <xigu at marvell.com>
Cc: Hua Jing <jinghua at marvell.com>
Cc: Terry Zhou <bjzhou at marvell.com>
Cc: Hanna Hawa <hannah at marvell.com>
Cc: Haim Boot <hayim at marvell.com>
---
drivers/serial/Kconfig | 15 ++++
drivers/serial/Makefile | 1 +
drivers/serial/serial_mvebu_a3700.c | 173 ++++++++++++++++++++++++++++++++++++
3 files changed, 189 insertions(+)
create mode 100644 drivers/serial/serial_mvebu_a3700.c
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index ab5df70..541cf2e 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -147,6 +147,13 @@ config DEBUG_UART_ARM_DCC
This port is available at least on ARMv6, ARMv7, ARMv8 and XScale
architectures.
+config DEBUG_MVEBU_A3700_UART
+ bool "Marvell Armada 3700"
+ help
+ Select this to enable a debug UART using the serial_mvebu driver. You
+ will need to provide parameters to make this work. The driver will
+ be available until the real driver-model serial is running.
+
config DEBUG_UART_ZYNQ
bool "Xilinx Zynq"
help
@@ -295,6 +302,13 @@ config FSL_LPUART
Select this to enable a Low Power UART for Freescale VF610 and
QorIQ Layerscape devices.
+config MVEBU_A3700_UART
+ bool "UART support for Armada 3700"
+ default n
+ help
+ Choose this option to add support for UART driver on the Marvell
+ Armada 3700 SoC. The base address is configured via DT.
+
config PIC32_SERIAL
bool "Support for Microchip PIC32 on-chip UART"
depends on DM_SERIAL && MACH_PIC32
@@ -371,4 +385,5 @@ config MSM_SERIAL
It should support all Qualcomm devices with UARTDM version 1.4,
for example APQ8016 and MSM8916.
Single baudrate is supported in current implementation (115200).
+
endmenu
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 6986d65..21b1292 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -46,6 +46,7 @@ obj-$(CONFIG_PIC32_SERIAL) += serial_pic32.o
obj-$(CONFIG_STM32X7_SERIAL) += serial_stm32x7.o
obj-$(CONFIG_BCM283X_MU_SERIAL) += serial_bcm283x_mu.o
obj-$(CONFIG_MSM_SERIAL) += serial_msm.o
+obj-$(CONFIG_MVEBU_A3700_UART) += serial_mvebu_a3700.o
ifndef CONFIG_SPL_BUILD
obj-$(CONFIG_USB_TTY) += usbtty.o
diff --git a/drivers/serial/serial_mvebu_a3700.c b/drivers/serial/serial_mvebu_a3700.c
new file mode 100644
index 0000000..e7b2db1
--- /dev/null
+++ b/drivers/serial/serial_mvebu_a3700.c
@@ -0,0 +1,173 @@
+/*
+ * Copyright (C) 2016 Stefan Roese <sr at denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <serial.h>
+#include <asm/io.h>
+
+struct mvebu_platdata {
+ void __iomem *base;
+};
+
+/*
+ * Register offset
+ */
+#define UART_RX_REG 0x00
+#define UART_TX_REG 0x04
+#define UART_CTRL_REG 0x08
+#define UART_STATUS_REG 0x0c
+#define UART_BAUD_REG 0x10
+#define UART_POSSR_REG 0x14
+
+#define UART_STATUS_RX_RDY 0x10
+#define UART_STATUS_TXFIFO_FULL 0x800
+
+#define UART_CTRL_RXFIFO_RESET 0x4000
+#define UART_CTRL_TXFIFO_RESET 0x8000
+
+static int mvebu_serial_putc(struct udevice *dev, const char ch)
+{
+ struct mvebu_platdata *plat = dev_get_platdata(dev);
+ void __iomem *base = plat->base;
+
+ while (readl(base + UART_STATUS_REG) & UART_STATUS_TXFIFO_FULL)
+ ;
+
+ writel(ch, base + UART_TX_REG);
+
+ return 0;
+}
+
+static int mvebu_serial_getc(struct udevice *dev)
+{
+ struct mvebu_platdata *plat = dev_get_platdata(dev);
+ void __iomem *base = plat->base;
+
+ while (!(readl(base + UART_STATUS_REG) & UART_STATUS_RX_RDY))
+ ;
+
+ return readl(base + UART_RX_REG) & 0xff;
+}
+
+static int mvebu_serial_pending(struct udevice *dev, bool input)
+{
+ struct mvebu_platdata *plat = dev_get_platdata(dev);
+ void __iomem *base = plat->base;
+
+ if (readl(base + UART_STATUS_REG) & UART_STATUS_RX_RDY)
+ return 1;
+
+ return 0;
+}
+
+static int mvebu_serial_setbrg(struct udevice *dev, int baudrate)
+{
+ struct mvebu_platdata *plat = dev_get_platdata(dev);
+ void __iomem *base = plat->base;
+
+ /*
+ * Calculate divider
+ * baudrate = clock / 16 / divider
+ */
+ writel(CONFIG_UART_BASE_CLOCK / baudrate / 16, base + UART_BAUD_REG);
+
+ /*
+ * Set Programmable Oversampling Stack to 0,
+ * UART defaults to 16x scheme
+ */
+ writel(0, base + UART_POSSR_REG);
+
+ return 0;
+}
+
+static int mvebu_serial_probe(struct udevice *dev)
+{
+ struct mvebu_platdata *plat = dev_get_platdata(dev);
+ void __iomem *base = plat->base;
+
+ /* reset FIFOs */
+ writel(UART_CTRL_RXFIFO_RESET | UART_CTRL_TXFIFO_RESET,
+ base + UART_CTRL_REG);
+
+ /* No Parity, 1 Stop */
+ writel(0, base + UART_CTRL_REG);
+
+ return 0;
+}
+
+static int mvebu_serial_ofdata_to_platdata(struct udevice *dev)
+{
+ struct mvebu_platdata *plat = dev_get_platdata(dev);
+
+ plat->base = dev_get_addr_ptr(dev);
+
+ return 0;
+}
+
+static const struct dm_serial_ops mvebu_serial_ops = {
+ .putc = mvebu_serial_putc,
+ .pending = mvebu_serial_pending,
+ .getc = mvebu_serial_getc,
+ .setbrg = mvebu_serial_setbrg,
+};
+
+static const struct udevice_id mvebu_serial_ids[] = {
+ { .compatible = "marvell,armada-3700-uart" },
+ { }
+};
+
+U_BOOT_DRIVER(serial_mvebu) = {
+ .name = "serial_mvebu",
+ .id = UCLASS_SERIAL,
+ .of_match = mvebu_serial_ids,
+ .ofdata_to_platdata = mvebu_serial_ofdata_to_platdata,
+ .platdata_auto_alloc_size = sizeof(struct mvebu_platdata),
+ .probe = mvebu_serial_probe,
+ .ops = &mvebu_serial_ops,
+ .flags = DM_FLAG_PRE_RELOC,
+};
+
+#ifdef CONFIG_DEBUG_MVEBU_A3700_UART
+
+#include <debug_uart.h>
+
+static inline void _debug_uart_init(void)
+{
+ void __iomem *base = (void __iomem *)CONFIG_DEBUG_UART_BASE;
+
+ /* reset FIFOs */
+ writel(UART_CTRL_RXFIFO_RESET | UART_CTRL_TXFIFO_RESET,
+ base + UART_CTRL_REG);
+
+ /* No Parity, 1 Stop */
+ writel(0, base + UART_CTRL_REG);
+
+ /*
+ * Calculate divider
+ * baudrate = clock / 16 / divider
+ */
+ writel(CONFIG_UART_BASE_CLOCK / 115200 / 16, base + UART_BAUD_REG);
+
+ /*
+ * Set Programmable Oversampling Stack to 0,
+ * UART defaults to 16x scheme
+ */
+ writel(0, base + UART_POSSR_REG);
+}
+
+static inline void _debug_uart_putc(int ch)
+{
+ void __iomem *base = (void __iomem *)CONFIG_DEBUG_UART_BASE;
+
+ while (readl(base + UART_STATUS_REG) & UART_STATUS_TXFIFO_FULL)
+ ;
+
+ writel(ch, base + UART_TX_REG);
+}
+
+DEBUG_UART_FUNCS
+#endif
--
2.9.3
More information about the U-Boot
mailing list