[U-Boot] [PATCH v5 00/21] imx6: Add Engicam i.CoreM6 QDL support

[Jagan Teki]

Hi Stefano,

On Wed, Sep 28, 2016 at 11:57 PM, Jagan Teki <jteki at openedev.com> wrote:
> From: Jagan Teki <jagan at amarulasolutions.com>
>
> This series supports Engicam i.CoreM6 QDL modules on top of u-boot-imx.git/next
> and test on the respective starter kits as well.
>
> Tested both MMC and NAND boot.
>
> Changes for v5:
>         - Add NAND support
>
> Changes for v4:
>         - Add 'net: Kconfig: Add FEC_MXC entry' patch
>         - Updated ENV configs along with comments
>         - Restructured configs for more readability
>         - Add CONFIG_ENV_OVERWRITE
>         - Rename icorem6qdl_defconfig with icorem6qdl_mmc_defconfig
>
> Changes for v3:
>         - Remove "v2 01/17 imx: iomux-v3: Fix build error with snvs base" patch
>         - Remove 'default n' on Kconfig DEFAULT_FDT_FILE patch
>         - Add minimal devicetree support for Engicam i.CoreM6 QDL
>         - Add is_mx6dl()
>         - Add is_mx6solo()
>         - Use is_mx6dq()
>         - Add last commit sha1 and header in pull devicetree files from Linux
>
> Changes for v2:
>         - Make static to local iomux structure in board file
>         - Corrected rowaddr in mx6_ddr3_cfg
>         - Used imx_ddr_size
>         - Add FEC support and tested the same
>         - Add DM_GPIO, DM_MMC support
>         - Add pinctrl support
>         - Add devicetree support
>
> Jagan Teki (21):
>   serial: Kconfig: Add MXC_UART entry
>   thermal: Kconfig: Add IMX_THERMAL entry
>   Kconfig: Add DEFAULT_FDT_FILE entry
>   arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support
>   net: Kconfig: Add FEC_MXC entry
>   imx6: icorem6: Add ENET support
>   imx: s/docs\/README.imximage/doc\/README.imximage/g
>   arm: dts: Add devicetree for i.MX6DL
>   arm: dts: Add devicetree for i.MX6DQL
>   arm: dts: imx6dl: Add pinctrl defines
>   dt-bindings: clock: imx6qdl: Add clock defines
>   arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
>   imx6q: icorem6: Enable pinctrl driver
>   engicam: icorem6: Add DM_GPIO, DM_MMC support
>   arm: dts: Add devicetree for i.MX6Q
>   arm: dts: imx6q: Add pinctrl defines
>   arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
>   mtd: nand: Kconfig: Add NAND_MXS entry
>   imx6: icorem6: Add NAND support
>   imx6: icorem6: Enable MTD device support
>   imx6: icorem6: Add default mtd nand partition table

Can you pick this series.

thanks!
-- 
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.