[U-Boot] [PATCH v1 5/7] spl: add serial download protocol (SDP) support

[Stefano Babic]

Hi Stefan,

On 05/08/2017 01:38, Stefan Agner wrote:
> From: Stefan Agner <stefan.agner at toradex.com>
> 
> Add USB serial download protocol support to SPL. If the SoC started
> in recovery mode the SPL will immediately switch to SDP and wait for
> further downloads/commands from the host side.
> 
> Signed-off-by: Stefan Agner <stefan.agner at toradex.com>
> ---
> 
>  common/spl/Kconfig          |  6 ++++++
>  common/spl/Makefile         |  1 +
>  common/spl/spl_sdp.c        | 38 ++++++++++++++++++++++++++++++++++++++
>  drivers/usb/gadget/Makefile |  1 +
>  4 files changed, 46 insertions(+)
>  create mode 100644 common/spl/spl_sdp.c
> 
> diff --git a/common/spl/Kconfig b/common/spl/Kconfig
> index 4de81392b0..95378b98a0 100644
> --- a/common/spl/Kconfig
> +++ b/common/spl/Kconfig
> @@ -646,6 +646,12 @@ config SPL_DFU_RAM
>  
>  endchoice
>  
> +config SPL_USB_SDP_SUPPORT
> +	bool "Support SDP (Serial Download Protocol)"
> +	help
> +	  Enable Serial Download Protocol (SDP) device support in SPL. This
> +	  allows to download images into memory and execute (jump to) them
> +	  using the same protocol as implemented by the i.MX family's boot ROM.
>  endif
>  
>  config SPL_WATCHDOG_SUPPORT
> diff --git a/common/spl/Makefile b/common/spl/Makefile
> index 47a64dd7d0..a979560acf 100644
> --- a/common/spl/Makefile
> +++ b/common/spl/Makefile
> @@ -29,4 +29,5 @@ obj-$(CONFIG_SPL_SATA_SUPPORT) += spl_sata.o
>  obj-$(CONFIG_SPL_DFU_SUPPORT) += spl_dfu.o
>  obj-$(CONFIG_SPL_SPI_LOAD) += spl_spi.o
>  obj-$(CONFIG_SPL_RAM_SUPPORT) += spl_ram.o
> +obj-$(CONFIG_SPL_USB_SDP_SUPPORT) += spl_sdp.o
>  endif
> diff --git a/common/spl/spl_sdp.c b/common/spl/spl_sdp.c
> new file mode 100644
> index 0000000000..faa74b8bec
> --- /dev/null
> +++ b/common/spl/spl_sdp.c
> @@ -0,0 +1,38 @@
> +/*
> + * (C) Copyright 2016 Toradex
> + * Author: Stefan Agner <stefan.agner at toradex.com>
> + *
> + * SPDX-License-Identifier:	GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <spl.h>
> +#include <usb.h>
> +#include <g_dnl.h>
> +#include <sdp.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +static int spl_sdp_load_image(struct spl_image_info *spl_image,
> +			      struct spl_boot_device *bootdev)
> +{
> +	int ret;
> +
> +	g_dnl_clear_detach();
> +	g_dnl_register("usb_dnl_sdp");
> +
> +	ret = sdp_init();
> +	if (ret) {
> +		error("SDP init failed: %d", ret);
> +		return -ENODEV;
> +	}
> +
> +	ret = sdp_handle();
> +	if (ret) {
> +		error("SDP failed: %d", ret);
> +		return -ENODEV;
> +	}
> +
> +	return 0;
> +}
> +SPL_LOAD_IMAGE_METHOD("USB SDP", 0, BOOT_DEVICE_UART, spl_sdp_load_image);
> diff --git a/drivers/usb/gadget/Makefile b/drivers/usb/gadget/Makefile
> index 6a007d1bcb..7258099c1c 100644
> --- a/drivers/usb/gadget/Makefile
> +++ b/drivers/usb/gadget/Makefile
> @@ -11,6 +11,7 @@ obj-$(CONFIG_USB_ETHER) += epautoconf.o config.o usbstring.o
>  ifdef CONFIG_SPL_BUILD
>  obj-$(CONFIG_SPL_USB_GADGET_SUPPORT) += g_dnl.o
>  obj-$(CONFIG_SPL_DFU_SUPPORT) += f_dfu.o
> +obj-$(CONFIG_SPL_USB_SDP_SUPPORT) += f_sdp.o
>  endif
>  
>  # new USB gadget layer dependencies
> 

Reviewed-by: Stefano Babic <sbabic at denx.de>

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================