[U-Boot] [PATCH v4 3/3] armv8: ls1088aqds: Add support of LS1088AQDS
Ashish Kumar
Ashish.Kumar at nxp.com
Fri Aug 18 05:44:51 UTC 2017
This patch add support of LS1088AQDS platform.
The LS1088A QorIQTM Development System (QDS) is a
high-performance computing, evaluation, and
development platform that supports the LS1088A QorIQ Architecture
processor.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha at nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie at nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar at nxp.com>
---
v2:
Fix indentaion in commit msg
v3:
Not sent
v4:
Review comments on V2 fixed
PPA enabled
README added
arch/arm/Kconfig | 13 +
arch/arm/cpu/armv8/Kconfig | 2 +-
arch/arm/dts/Makefile | 3 +-
arch/arm/dts/fsl-ls1088a-qds.dts | 70 ++++
board/freescale/ls1088a/Kconfig | 16 +
board/freescale/ls1088a/MAINTAINERS | 8 +
board/freescale/ls1088a/Makefile | 1 +
board/freescale/ls1088a/README | 79 ++++
board/freescale/ls1088a/ddr.h | 5 +
board/freescale/ls1088a/eth_ls1088aqds.c | 650 +++++++++++++++++++++++++++++++
board/freescale/ls1088a/ls1088a.c | 87 ++++-
board/freescale/ls1088a/ls1088a_qixis.h | 5 +
configs/ls1088aqds_qspi_defconfig | 29 ++
include/configs/ls1088aqds.h | 414 ++++++++++++++++++++
14 files changed, 1372 insertions(+), 10 deletions(-)
create mode 100644 arch/arm/dts/fsl-ls1088a-qds.dts
create mode 100644 board/freescale/ls1088a/eth_ls1088aqds.c
create mode 100644 configs/ls1088aqds_qspi_defconfig
create mode 100644 include/configs/ls1088aqds.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index eaeab27..c96bbb4 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -791,6 +791,19 @@ config TARGET_LS2080A_SIMU
development platform that supports the QorIQ LS2080A
Layerscape Architecture processor.
+config TARGET_LS1088AQDS
+ bool "Support ls1088aqds"
+ select ARCH_LS1088A
+ select ARM64
+ select ARMV8_MULTIENTRY
+ select ARCH_MISC_INIT
+ select BOARD_LATE_INIT
+ help
+ Support for NXP LS1088AQDS platform
+ The LS1088A Development System (QDS) is a high-performance
+ development platform that supports the QorIQ LS1088A
+ Layerscape Architecture processor.
+
config TARGET_LS2080AQDS
bool "Support ls2080aqds"
select ARCH_LS2080A
diff --git a/arch/arm/cpu/armv8/Kconfig b/arch/arm/cpu/armv8/Kconfig
index aecdf81..12aba9d 100644
--- a/arch/arm/cpu/armv8/Kconfig
+++ b/arch/arm/cpu/armv8/Kconfig
@@ -88,7 +88,7 @@ config PSCI_RESET
depends on !ARCH_EXYNOS7 && !ARCH_BCM283X && !TARGET_LS2080A_EMU && \
!TARGET_LS2080A_SIMU && !TARGET_LS2080AQDS && \
!TARGET_LS2080ARDB && !TARGET_LS1012AQDS && \
- !TARGET_LS1088ARDB && \
+ !TARGET_LS1088ARDB && !TARGET_LS1088AQDS && \
!TARGET_LS1012ARDB && !TARGET_LS1012AFRDM && \
!TARGET_LS1043ARDB && !TARGET_LS1043AQDS && \
!TARGET_LS1046ARDB && !TARGET_LS1046AQDS && \
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 6f03a3f..06c6340 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -189,7 +189,8 @@ dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \
fsl-ls2080a-rdb.dtb \
fsl-ls2081a-rdb.dtb \
fsl-ls2088a-rdb-qspi.dtb \
- fsl-ls1088a-rdb.dtb
+ fsl-ls1088a-rdb.dtb \
+ fsl-ls1088a-qds.dtb
dtb-$(CONFIG_FSL_LSCH2) += fsl-ls1043a-qds-duart.dtb \
fsl-ls1043a-qds-lpuart.dtb \
fsl-ls1043a-rdb.dtb \
diff --git a/arch/arm/dts/fsl-ls1088a-qds.dts b/arch/arm/dts/fsl-ls1088a-qds.dts
new file mode 100644
index 0000000..9b7bef4
--- /dev/null
+++ b/arch/arm/dts/fsl-ls1088a-qds.dts
@@ -0,0 +1,70 @@
+/*
+ * NXP ls1088a QDS board device tree source
+ *
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/dts-v1/;
+
+#include "fsl-ls1088a.dtsi"
+
+/ {
+ model = "NXP Layerscape 1088a QDS Board";
+ compatible = "fsl,ls1088a-qds", "fsl,ls1088a";
+ aliases {
+ spi0 = &qspi;
+ spi1 = &dspi;
+ };
+};
+
+&dspi {
+ bus-num = <0>;
+ status = "okay";
+
+ dflash0: n25q128a {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-flash";
+ reg = <0>;
+ spi-max-frequency = <1000000>; /* input clock */
+ };
+
+ dflash1: sst25wf040b {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-flash";
+ spi-max-frequency = <3500000>;
+ reg = <1>;
+ };
+
+ dflash2: en25s64 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-flash";
+ spi-max-frequency = <3500000>;
+ reg = <2>;
+ };
+};
+
+&qspi {
+ bus-num = <0>;
+ status = "okay";
+
+ qflash0: s25fs512s at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-flash";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
+
+ qflash1: s25fs512s at 1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-flash";
+ spi-max-frequency = <50000000>;
+ reg = <1>;
+ };
+};
diff --git a/board/freescale/ls1088a/Kconfig b/board/freescale/ls1088a/Kconfig
index a4d8223..1ada661 100644
--- a/board/freescale/ls1088a/Kconfig
+++ b/board/freescale/ls1088a/Kconfig
@@ -1,3 +1,19 @@
+if TARGET_LS1088AQDS
+
+config SYS_BOARD
+ default "ls1088a"
+
+config SYS_VENDOR
+ default "freescale"
+
+config SYS_SOC
+ default "fsl-layerscape"
+
+config SYS_CONFIG_NAME
+ default "ls1088aqds"
+
+endif
+
if TARGET_LS1088ARDB
config SYS_BOARD
diff --git a/board/freescale/ls1088a/MAINTAINERS b/board/freescale/ls1088a/MAINTAINERS
index 12834f6..e1e6d4b 100644
--- a/board/freescale/ls1088a/MAINTAINERS
+++ b/board/freescale/ls1088a/MAINTAINERS
@@ -5,3 +5,11 @@ S: Maintained
F: board/freescale/ls1088a/
F: include/configs/ls1088ardb.h
F: configs/ls1088ardb_qspi_defconfig
+
+LS1088AQDS BOARD
+M: Prabhakar Kushwaha <prabhakar.kushwaha at nxp.com>
+M: Ashish Kumar <Ashish.Kumar at nxp.com>
+S: Maintained
+F: board/freescale/ls1088a/
+F: include/configs/ls1088aqds.h
+F: configs/ls1088aqds_qspi_defconfig
diff --git a/board/freescale/ls1088a/Makefile b/board/freescale/ls1088a/Makefile
index e997cf1..bdcce9e 100644
--- a/board/freescale/ls1088a/Makefile
+++ b/board/freescale/ls1088a/Makefile
@@ -6,4 +6,5 @@
obj-y += ls1088a.o
obj-$(CONFIG_TARGET_LS1088ARDB) += eth_ls1088ardb.o
+obj-$(CONFIG_TARGET_LS1088AQDS) += eth_ls1088aqds.o
obj-y += ddr.o
diff --git a/board/freescale/ls1088a/README b/board/freescale/ls1088a/README
index 3f4d987..aa0fb6a 100644
--- a/board/freescale/ls1088a/README
+++ b/board/freescale/ls1088a/README
@@ -64,3 +64,82 @@ Alternately you can use this command to switch from QSPI to SD
- JTAG support
- QSPI emulator support
- TDM riser support
+
+QDS Default Switch Settings (1: ON; 0: OFF)
+-------------------------------------------
+
+For 16b IFC-NOR
+SW1 0001 0010
+SW2 x110 1111
+
+For QSPI Boot
+SW1 0011 0001
+SW2 0110 1111
+
+For SD Boot
+SW1 0010 0000
+SW2 0110 1111
+
+For eMMC Boot
+SW1 0010 0000
+SW2 1110 1111
+
+For I2C (ext. addr.)
+SW1 0010 0100
+SW2 1110 1111
+
+SW3 to SW12 are identical for all boot source
+
+SW3 0010 0100
+SW4 0010 0000
+SW5 1110 0111
+SW6 1110 1000
+SW7 0001 1101
+SW8 0000 1101
+SW9 1100 1010
+SW10 1110 1000
+SW11 1111 0100
+SW12 1111 1111
+
+ LS1088AQDS board Overview
+ -------------------------
+ - SERDES Connections, 16 lanes supporting:
+ - PCI Express - 3.0
+ - SATA 3.0
+ - 2 XFI
+ - QSGMII, SGMII with help for Riser card
+ - 2 RGMII
+ - 5 slot for Riser card or PCIe NIC
+ - DDR Controller
+ - One ports of 72-bits (8-bits ECC, 64-bits DATA) DDR4. Each port supports four
+ chip-selects on one DIMM connector. Support is up to 2133MT/s, Although MAX default
+ with FSL refernce software is 2100MT/s
+ - 2 QSPI-NOR Spansion(S25FS512SDSMFI011) flash of size 64MB
+ - IFC/Local Bus
+ - One 2 GB NAND flash with ECC support, not as boot source
+ - CPLD of size 2K
+ - USB 3.0
+ - Two high speed USB 3.0 ports
+ - First USB 3.0 port configured as Host with Type-A connector
+ - Second USB 3.0 port configured as OTG with micro-AB connector
+ - SDHC/eMMC
+ - SDHC/eMMC slot via adaptor
+ - 4 I2C controllers
+ - Two SATA onboard connectors
+ - 2 UART
+ - JTAG support
+ - DSPI
+ - PROMJET support
+ - QSPI emulator support
+ - TDM riser support
+
+QSPI flash memory map valid for both QDS and RDB
+ Image Flash Offset
+ RCW+PBI 0x00000000
+ Boot firmware (U-Boot) 0x00100000
+ Boot firmware Environment 0x00300000
+ PPA firmware 0x00400000
+ DPAA2 MC 0x00A00000
+ DPAA2 DPL 0x00D00000
+ DPAA2 DPC 0x00E00000
+ Kernel.itb 0x01000000
diff --git a/board/freescale/ls1088a/ddr.h b/board/freescale/ls1088a/ddr.h
index dfcfc1f..a1ad709 100644
--- a/board/freescale/ls1088a/ddr.h
+++ b/board/freescale/ls1088a/ddr.h
@@ -34,6 +34,11 @@ static const struct board_specific_parameters udimm0[] = {
{2, 1900, 0, 4, 7, 0x09090B0D, 0x0E10120B,},
{2, 2300, 0, 8, 9, 0x0A0C0E11, 0x1214160F,},
{}
+#elif defined(CONFIG_TARGET_LS1088AQDS)
+ {2, 1666, 0, 8, 8, 0x0A0A0C0E, 0x0F10110C,},
+ {2, 1900, 0, 4, 7, 0x09090B0D, 0x0E10120B,},
+ {2, 2300, 0, 4, 9, 0x0A0C0D11, 0x1214150E,},
+ {}
#endif
};
diff --git a/board/freescale/ls1088a/eth_ls1088aqds.c b/board/freescale/ls1088a/eth_ls1088aqds.c
new file mode 100644
index 0000000..3e78ac7
--- /dev/null
+++ b/board/freescale/ls1088a/eth_ls1088aqds.c
@@ -0,0 +1,650 @@
+/*
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/arch/fsl_serdes.h>
+#include <hwconfig.h>
+#include <fsl_mdio.h>
+#include <malloc.h>
+#include <fm_eth.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <fsl-mc/ldpaa_wriop.h>
+
+#include "../common/qixis.h"
+
+#include "ls1088a_qixis.h"
+
+#define MC_BOOT_ENV_VAR "mcinitcmd"
+
+#ifdef CONFIG_FSL_MC_ENET
+
+#define SFP_TX 0
+
+ /* - In LS1088A A there are only 16 SERDES lanes, spread across 2 SERDES banks.
+ * Bank 1 -> Lanes A, B, C, D,
+ * Bank 2 -> Lanes A,B, C, D,
+ */
+
+ /* Mapping of 8 SERDES lanes to LS1088A QDS board slots. A value of '0' here
+ * means that the mapping must be determined dynamically, or that the lane
+ * maps to something other than a board slot.
+ */
+
+static u8 lane_to_slot_fsm1[] = {
+ 0, 0, 0, 0, 0, 0, 0, 0
+};
+
+/* On the Vitesse VSC8234XHG SGMII riser card there are 4 SGMII PHYs
+ * housed.
+ */
+
+static int xqsgii_riser_phy_addr[] = {
+ XQSGMII_CARD_PHY1_PORT0_ADDR,
+ XQSGMII_CARD_PHY2_PORT0_ADDR,
+ XQSGMII_CARD_PHY3_PORT0_ADDR,
+ XQSGMII_CARD_PHY4_PORT0_ADDR,
+ XQSGMII_CARD_PHY3_PORT2_ADDR,
+ XQSGMII_CARD_PHY1_PORT2_ADDR,
+ XQSGMII_CARD_PHY4_PORT2_ADDR,
+ XQSGMII_CARD_PHY2_PORT2_ADDR,
+};
+
+static int sgmii_riser_phy_addr[] = {
+ SGMII_CARD_PORT1_PHY_ADDR,
+ SGMII_CARD_PORT2_PHY_ADDR,
+ SGMII_CARD_PORT3_PHY_ADDR,
+ SGMII_CARD_PORT4_PHY_ADDR,
+};
+
+/* Slot2 does not have EMI connections */
+#define EMI_NONE 0xFF
+#define EMI1_RGMII1 0
+#define EMI1_RGMII2 1
+#define EMI1_SLOT1 2
+
+static const char * const mdio_names[] = {
+ "LS1088A_QDS_MDIO0",
+ "LS1088A_QDS_MDIO1",
+ "LS1088A_QDS_MDIO2",
+ DEFAULT_WRIOP_MDIO2_NAME,
+};
+
+struct ls1088a_qds_mdio {
+ u8 muxval;
+ struct mii_dev *realbus;
+};
+
+static void sgmii_configure_repeater(int dpmac)
+{
+ struct mii_dev *bus;
+ uint8_t a = 0xf;
+ int i, j, ret;
+ unsigned short value;
+ const char *dev = "LS1088A_QDS_MDIO2";
+ int i2c_addr[] = {0x58, 0x59, 0x5a, 0x5b};
+ int i2c_phy_addr = 0;
+ int phy_addr = 0;
+
+ uint8_t ch_a_eq[] = {0x1, 0x2, 0x3, 0x7};
+ uint8_t ch_a_ctl2[] = {0x81, 0x82, 0x83, 0x84};
+ uint8_t ch_b_eq[] = {0x1, 0x2, 0x3, 0x7};
+ uint8_t ch_b_ctl2[] = {0x81, 0x82, 0x83, 0x84};
+
+ /* Set I2c to Slot 1 */
+ i2c_write(0x77, 0, 0, &a, 1);
+
+ switch (dpmac) {
+ case 1:
+ i2c_phy_addr = i2c_addr[1];
+ phy_addr = 4;
+ break;
+ case 2:
+ i2c_phy_addr = i2c_addr[0];
+ phy_addr = 0;
+ break;
+ case 3:
+ i2c_phy_addr = i2c_addr[3];
+ phy_addr = 0xc;
+ break;
+ case 7:
+ i2c_phy_addr = i2c_addr[2];
+ phy_addr = 8;
+ break;
+ }
+
+ /* Check the PHY status */
+ ret = miiphy_set_current_dev(dev);
+ if (ret > 0)
+ goto error;
+
+ bus = mdio_get_current_dev();
+ debug("Reading from bus %s\n", bus->name);
+
+ ret = miiphy_write(dev, phy_addr, 0x1f, 3);
+ if (ret > 0)
+ goto error;
+
+ mdelay(10);
+ ret = miiphy_read(dev, phy_addr, 0x11, &value);
+ if (ret > 0)
+ goto error;
+
+ mdelay(10);
+
+ if ((value & 0xfff) == 0x401) {
+ miiphy_write(dev, phy_addr, 0x1f, 0);
+ printf("DPMAC %d:PHY is ..... Configured\n", dpmac);
+ return;
+ }
+
+ for (i = 0; i < 4; i++) {
+ for (j = 0; j < 4; j++) {
+ a = 0x18;
+ i2c_write(i2c_phy_addr, 6, 1, &a, 1);
+ a = 0x38;
+ i2c_write(i2c_phy_addr, 4, 1, &a, 1);
+ a = 0x4;
+ i2c_write(i2c_phy_addr, 8, 1, &a, 1);
+
+ i2c_write(i2c_phy_addr, 0xf, 1,
+ &ch_a_eq[i], 1);
+ i2c_write(i2c_phy_addr, 0x11, 1,
+ &ch_a_ctl2[j], 1);
+
+ i2c_write(i2c_phy_addr, 0x16, 1,
+ &ch_b_eq[i], 1);
+ i2c_write(i2c_phy_addr, 0x18, 1,
+ &ch_b_ctl2[j], 1);
+
+ a = 0x14;
+ i2c_write(i2c_phy_addr, 0x23, 1, &a, 1);
+ a = 0xb5;
+ i2c_write(i2c_phy_addr, 0x2d, 1, &a, 1);
+ a = 0x20;
+ i2c_write(i2c_phy_addr, 4, 1, &a, 1);
+ mdelay(100);
+ ret = miiphy_read(dev, phy_addr, 0x11, &value);
+ if (ret > 0)
+ goto error;
+
+ mdelay(100);
+ ret = miiphy_read(dev, phy_addr, 0x11, &value);
+ if (ret > 0)
+ goto error;
+
+ if ((value & 0xfff) == 0x401) {
+ printf("DPMAC %d :PHY is configured ",
+ dpmac);
+ printf("after setting repeater 0x%x\n",
+ value);
+ i = 5;
+ j = 5;
+ } else {
+ printf("DPMAC %d :PHY is failed to ",
+ dpmac);
+ printf("configure the repeater 0x%x\n", value);
+ }
+ }
+ }
+ miiphy_write(dev, phy_addr, 0x1f, 0);
+error:
+ if (ret)
+ printf("DPMAC %d ..... FAILED to configure PHY\n", dpmac);
+ return;
+}
+
+static void qsgmii_configure_repeater(int dpmac)
+{
+ uint8_t a = 0xf;
+ int i, j;
+ int i2c_phy_addr = 0;
+ int phy_addr = 0;
+ int i2c_addr[] = {0x58, 0x59, 0x5a, 0x5b};
+
+ uint8_t ch_a_eq[] = {0x1, 0x2, 0x3, 0x7};
+ uint8_t ch_a_ctl2[] = {0x81, 0x82, 0x83, 0x84};
+ uint8_t ch_b_eq[] = {0x1, 0x2, 0x3, 0x7};
+ uint8_t ch_b_ctl2[] = {0x81, 0x82, 0x83, 0x84};
+
+ const char *dev = mdio_names[EMI1_SLOT1];
+ int ret = 0;
+ unsigned short value;
+
+ /* Set I2c to Slot 1 */
+ i2c_write(0x77, 0, 0, &a, 1);
+
+ switch (dpmac) {
+ case 7:
+ case 8:
+ case 9:
+ case 10:
+ i2c_phy_addr = i2c_addr[2];
+ phy_addr = 8;
+ break;
+
+ case 3:
+ case 4:
+ case 5:
+ case 6:
+ i2c_phy_addr = i2c_addr[3];
+ phy_addr = 0xc;
+ break;
+ }
+
+ /* Check the PHY status */
+ ret = miiphy_set_current_dev(dev);
+ ret = miiphy_write(dev, phy_addr, 0x1f, 3);
+ mdelay(10);
+ ret = miiphy_read(dev, phy_addr, 0x11, &value);
+ mdelay(10);
+ ret = miiphy_read(dev, phy_addr, 0x11, &value);
+ mdelay(10);
+ if ((value & 0xf) == 0xf) {
+ miiphy_write(dev, phy_addr, 0x1f, 0);
+ printf("DPMAC %d :PHY is ..... Configured\n", dpmac);
+ return;
+ }
+
+ for (i = 0; i < 4; i++) {
+ for (j = 0; j < 4; j++) {
+ a = 0x18;
+ i2c_write(i2c_phy_addr, 6, 1, &a, 1);
+ a = 0x38;
+ i2c_write(i2c_phy_addr, 4, 1, &a, 1);
+ a = 0x4;
+ i2c_write(i2c_phy_addr, 8, 1, &a, 1);
+
+ i2c_write(i2c_phy_addr, 0xf, 1, &ch_a_eq[i], 1);
+ i2c_write(i2c_phy_addr, 0x11, 1, &ch_a_ctl2[j], 1);
+
+ i2c_write(i2c_phy_addr, 0x16, 1, &ch_b_eq[i], 1);
+ i2c_write(i2c_phy_addr, 0x18, 1, &ch_b_ctl2[j], 1);
+
+ a = 0x14;
+ i2c_write(i2c_phy_addr, 0x23, 1, &a, 1);
+ a = 0xb5;
+ i2c_write(i2c_phy_addr, 0x2d, 1, &a, 1);
+ a = 0x20;
+ i2c_write(i2c_phy_addr, 4, 1, &a, 1);
+ mdelay(100);
+ ret = miiphy_read(dev, phy_addr, 0x11, &value);
+ if (ret > 0)
+ goto error;
+ mdelay(1);
+ ret = miiphy_read(dev, phy_addr, 0x11, &value);
+ if (ret > 0)
+ goto error;
+ mdelay(10);
+ if ((value & 0xf) == 0xf) {
+ miiphy_write(dev, phy_addr, 0x1f, 0);
+ printf("DPMAC %d :PHY is ..... Configured\n",
+ dpmac);
+ return;
+ }
+ }
+ }
+error:
+ printf("DPMAC %d :PHY ..... FAILED to configure PHY\n", dpmac);
+ return;
+}
+
+static const char *ls1088a_qds_mdio_name_for_muxval(u8 muxval)
+{
+ return mdio_names[muxval];
+}
+
+struct mii_dev *mii_dev_for_muxval(u8 muxval)
+{
+ struct mii_dev *bus;
+ const char *name = ls1088a_qds_mdio_name_for_muxval(muxval);
+
+ if (!name) {
+ printf("No bus for muxval %x\n", muxval);
+ return NULL;
+ }
+
+ bus = miiphy_get_dev_by_name(name);
+
+ if (!bus) {
+ printf("No bus by name %s\n", name);
+ return NULL;
+ }
+
+ return bus;
+}
+
+static void ls1088a_qds_enable_SFP_TX(u8 muxval)
+{
+ u8 brdcfg9;
+
+ brdcfg9 = QIXIS_READ(brdcfg[9]);
+ brdcfg9 &= ~BRDCFG9_SFPTX_MASK;
+ brdcfg9 |= (muxval << BRDCFG9_SFPTX_SHIFT);
+ QIXIS_WRITE(brdcfg[9], brdcfg9);
+}
+
+static void ls1088a_qds_mux_mdio(u8 muxval)
+{
+ u8 brdcfg4;
+
+ if (muxval <= 5) {
+ brdcfg4 = QIXIS_READ(brdcfg[4]);
+ brdcfg4 &= ~BRDCFG4_EMISEL_MASK;
+ brdcfg4 |= (muxval << BRDCFG4_EMISEL_SHIFT);
+ QIXIS_WRITE(brdcfg[4], brdcfg4);
+ }
+}
+
+static int ls1088a_qds_mdio_read(struct mii_dev *bus, int addr,
+ int devad, int regnum)
+{
+ struct ls1088a_qds_mdio *priv = bus->priv;
+
+ ls1088a_qds_mux_mdio(priv->muxval);
+
+ return priv->realbus->read(priv->realbus, addr, devad, regnum);
+}
+
+static int ls1088a_qds_mdio_write(struct mii_dev *bus, int addr, int devad,
+ int regnum, u16 value)
+{
+ struct ls1088a_qds_mdio *priv = bus->priv;
+
+ ls1088a_qds_mux_mdio(priv->muxval);
+
+ return priv->realbus->write(priv->realbus, addr, devad, regnum, value);
+}
+
+static int ls1088a_qds_mdio_reset(struct mii_dev *bus)
+{
+ struct ls1088a_qds_mdio *priv = bus->priv;
+
+ return priv->realbus->reset(priv->realbus);
+}
+
+static int ls1088a_qds_mdio_init(char *realbusname, u8 muxval)
+{
+ struct ls1088a_qds_mdio *pmdio;
+ struct mii_dev *bus = mdio_alloc();
+
+ if (!bus) {
+ printf("Failed to allocate ls1088a_qds MDIO bus\n");
+ return -1;
+ }
+
+ pmdio = malloc(sizeof(*pmdio));
+ if (!pmdio) {
+ printf("Failed to allocate ls1088a_qds private data\n");
+ free(bus);
+ return -1;
+ }
+
+ bus->read = ls1088a_qds_mdio_read;
+ bus->write = ls1088a_qds_mdio_write;
+ bus->reset = ls1088a_qds_mdio_reset;
+ sprintf(bus->name, ls1088a_qds_mdio_name_for_muxval(muxval));
+
+ pmdio->realbus = miiphy_get_dev_by_name(realbusname);
+
+ if (!pmdio->realbus) {
+ printf("No bus with name %s\n", realbusname);
+ free(bus);
+ free(pmdio);
+ return -1;
+ }
+
+ pmdio->muxval = muxval;
+ bus->priv = pmdio;
+
+ return mdio_register(bus);
+}
+
+/*
+ * Initialize the dpmac_info array.
+ *
+ */
+static void initialize_dpmac_to_slot(void)
+{
+ struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
+ u32 serdes1_prtcl, cfg;
+
+ cfg = in_le32(&gur->rcwsr[FSL_CHASSIS3_SRDS1_REGSR - 1]) &
+ FSL_CHASSIS3_SRDS1_PRTCL_MASK;
+ cfg >>= FSL_CHASSIS3_SRDS1_PRTCL_SHIFT;
+ serdes1_prtcl = serdes_get_number(FSL_SRDS_1, cfg);
+
+ switch (serdes1_prtcl) {
+ case 0x12:
+ printf("qds: WRIOP: Supported SerDes1 Protocol 0x%02x\n",
+ serdes1_prtcl);
+ lane_to_slot_fsm1[0] = EMI1_SLOT1 - 1;
+ lane_to_slot_fsm1[1] = EMI1_SLOT1 - 1;
+ lane_to_slot_fsm1[2] = EMI1_SLOT1 - 1;
+ lane_to_slot_fsm1[3] = EMI1_SLOT1 - 1;
+ break;
+ case 0x15:
+ case 0x1D:
+ printf("qds: WRIOP: Supported SerDes1 Protocol 0x%02x\n",
+ serdes1_prtcl);
+ lane_to_slot_fsm1[0] = EMI1_SLOT1 - 1;
+ lane_to_slot_fsm1[1] = EMI1_SLOT1 - 1;
+ lane_to_slot_fsm1[2] = EMI_NONE;
+ lane_to_slot_fsm1[3] = EMI_NONE;
+ break;
+ case 0x1E:
+ printf("qds: WRIOP: Supported SerDes1 Protocol 0x%02x\n",
+ serdes1_prtcl);
+ lane_to_slot_fsm1[0] = EMI1_SLOT1 - 1;
+ lane_to_slot_fsm1[1] = EMI1_SLOT1 - 1;
+ lane_to_slot_fsm1[2] = EMI1_SLOT1 - 1;
+ lane_to_slot_fsm1[3] = EMI_NONE;
+ break;
+ case 0x3A:
+ printf("qds: WRIOP: Supported SerDes1 Protocol 0x%02x\n",
+ serdes1_prtcl);
+ lane_to_slot_fsm1[0] = EMI1_SLOT1 - 1;
+ lane_to_slot_fsm1[1] = EMI_NONE;
+ lane_to_slot_fsm1[2] = EMI1_SLOT1 - 1;
+ lane_to_slot_fsm1[3] = EMI1_SLOT1 - 1;
+ break;
+
+ default:
+ printf("%s qds: WRIOP: Unsupported SerDes1 Protocol 0x%02x\n",
+ __func__, serdes1_prtcl);
+ break;
+ }
+}
+
+void ls1088a_handle_phy_interface_sgmii(int dpmac_id)
+{
+ struct mii_dev *bus;
+ struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
+ u32 serdes1_prtcl, cfg;
+
+ cfg = in_le32(&gur->rcwsr[FSL_CHASSIS3_SRDS1_REGSR - 1]) &
+ FSL_CHASSIS3_SRDS1_PRTCL_MASK;
+ cfg >>= FSL_CHASSIS3_SRDS1_PRTCL_SHIFT;
+ serdes1_prtcl = serdes_get_number(FSL_SRDS_1, cfg);
+
+ int *riser_phy_addr;
+ char *env_hwconfig = getenv("hwconfig");
+
+ if (hwconfig_f("xqsgmii", env_hwconfig))
+ riser_phy_addr = &xqsgii_riser_phy_addr[0];
+ else
+ riser_phy_addr = &sgmii_riser_phy_addr[0];
+
+ switch (serdes1_prtcl) {
+ case 0x12:
+ case 0x15:
+ case 0x1E:
+ case 0x3A:
+ switch (dpmac_id) {
+ case 1:
+ wriop_set_phy_address(dpmac_id, riser_phy_addr[1]);
+ break;
+ case 2:
+ wriop_set_phy_address(dpmac_id, riser_phy_addr[0]);
+ break;
+ case 3:
+ wriop_set_phy_address(dpmac_id, riser_phy_addr[3]);
+ break;
+ case 7:
+ wriop_set_phy_address(dpmac_id, riser_phy_addr[2]);
+ break;
+ default:
+ printf("WRIOP: Wrong DPMAC%d set to SGMII", dpmac_id);
+ break;
+ }
+ break;
+ default:
+ printf("%s qds: WRIOP: Unsupported SerDes1 Protocol 0x%02x\n",
+ __func__, serdes1_prtcl);
+ return;
+ }
+ dpmac_info[dpmac_id].board_mux = EMI1_SLOT1;
+ bus = mii_dev_for_muxval(EMI1_SLOT1);
+ wriop_set_mdio(dpmac_id, bus);
+}
+
+void ls1088a_handle_phy_interface_qsgmii(int dpmac_id)
+{
+ struct mii_dev *bus;
+ struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
+ u32 serdes1_prtcl, cfg;
+
+ cfg = in_le32(&gur->rcwsr[FSL_CHASSIS3_SRDS1_REGSR - 1]) &
+ FSL_CHASSIS3_SRDS1_PRTCL_MASK;
+ cfg >>= FSL_CHASSIS3_SRDS1_PRTCL_SHIFT;
+ serdes1_prtcl = serdes_get_number(FSL_SRDS_1, cfg);
+
+ switch (serdes1_prtcl) {
+ case 0x1D:
+ case 0x1E:
+ switch (dpmac_id) {
+ case 3:
+ case 4:
+ case 5:
+ case 6:
+ wriop_set_phy_address(dpmac_id, dpmac_id + 9);
+ break;
+ case 7:
+ case 8:
+ case 9:
+ case 10:
+ wriop_set_phy_address(dpmac_id, dpmac_id + 1);
+ break;
+ }
+
+ dpmac_info[dpmac_id].board_mux = EMI1_SLOT1;
+ bus = mii_dev_for_muxval(EMI1_SLOT1);
+ wriop_set_mdio(dpmac_id, bus);
+ break;
+ default:
+ printf("qds: WRIOP: Unsupported SerDes Protocol 0x%02x\n",
+ serdes1_prtcl);
+ break;
+ }
+}
+
+void ls1088a_handle_phy_interface_xsgmii(int i)
+{
+ struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
+ u32 serdes1_prtcl, cfg;
+
+ cfg = in_le32(&gur->rcwsr[FSL_CHASSIS3_SRDS1_REGSR - 1]) &
+ FSL_CHASSIS3_SRDS1_PRTCL_MASK;
+ cfg >>= FSL_CHASSIS3_SRDS1_PRTCL_SHIFT;
+ serdes1_prtcl = serdes_get_number(FSL_SRDS_1, cfg);
+
+ switch (serdes1_prtcl) {
+ case 0x15:
+ case 0x1D:
+ case 0x1E:
+ wriop_set_phy_address(i, i + 26);
+ ls1088a_qds_enable_SFP_TX(SFP_TX);
+ break;
+ default:
+ printf("qds: WRIOP: Unsupported SerDes Protocol 0x%02x\n",
+ serdes1_prtcl);
+ break;
+ }
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+ int error = 0, i;
+ char *mc_boot_env_var;
+#ifdef CONFIG_FSL_MC_ENET
+ struct memac_mdio_info *memac_mdio0_info;
+ char *env_hwconfig = getenv("hwconfig");
+
+ initialize_dpmac_to_slot();
+
+ memac_mdio0_info = (struct memac_mdio_info *)malloc(
+ sizeof(struct memac_mdio_info));
+ memac_mdio0_info->regs =
+ (struct memac_mdio_controller *)
+ CONFIG_SYS_FSL_WRIOP1_MDIO1;
+ memac_mdio0_info->name = DEFAULT_WRIOP_MDIO1_NAME;
+
+ /* Register the real MDIO1 bus */
+ fm_memac_mdio_init(bis, memac_mdio0_info);
+
+ /* Register the muxing front-ends to the MDIO buses */
+ ls1088a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_RGMII1);
+ ls1088a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_RGMII2);
+ ls1088a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_SLOT1);
+
+ for (i = WRIOP1_DPMAC1; i < NUM_WRIOP_PORTS; i++) {
+ switch (wriop_get_enet_if(i)) {
+ case PHY_INTERFACE_MODE_QSGMII:
+ ls1088a_handle_phy_interface_qsgmii(i);
+ break;
+ case PHY_INTERFACE_MODE_SGMII:
+ ls1088a_handle_phy_interface_sgmii(i);
+ break;
+ case PHY_INTERFACE_MODE_XGMII:
+ ls1088a_handle_phy_interface_xsgmii(i);
+ break;
+ default:
+ break;
+
+ if (i == 16)
+ i = NUM_WRIOP_PORTS;
+ }
+ }
+
+ mc_boot_env_var = getenv(MC_BOOT_ENV_VAR);
+ if (mc_boot_env_var)
+ run_command_list(mc_boot_env_var, -1, 0);
+ error = cpu_eth_init(bis);
+
+ if (hwconfig_f("xqsgmii", env_hwconfig)) {
+ for (i = WRIOP1_DPMAC1; i < NUM_WRIOP_PORTS; i++) {
+ switch (wriop_get_enet_if(i)) {
+ case PHY_INTERFACE_MODE_QSGMII:
+ qsgmii_configure_repeater(i);
+ break;
+ case PHY_INTERFACE_MODE_SGMII:
+ sgmii_configure_repeater(i);
+ break;
+ default:
+ break;
+ }
+
+ if (i == 16)
+ i = NUM_WRIOP_PORTS;
+ }
+ }
+#endif
+ error = pci_eth_init(bis);
+ return error;
+}
diff --git a/board/freescale/ls1088a/ls1088a.c b/board/freescale/ls1088a/ls1088a.c
index f3c20ac..d1de4d1 100644
--- a/board/freescale/ls1088a/ls1088a.c
+++ b/board/freescale/ls1088a/ls1088a.c
@@ -50,14 +50,20 @@ int checkboard(void)
"100 separate SSCG"};
int clock;
-
+#ifdef CONFIG_TARGET_LS1088AQDS
+ printf("Board: LS1088A-QDS, ");
+#else
printf("Board: LS1088A-RDB, ");
+#endif
sw = QIXIS_READ(arch);
printf("Board Arch: V%d, ", sw >> 4);
+#ifdef CONFIG_TARGET_LS1088AQDS
+ printf("Board version: %c, boot from ", (sw & 0xf) + 'A' - 1);
+#else
printf("Board version: %c, boot from ", (sw & 0xf) + 'A');
-
+#endif
memset((u8 *)buf, 0x00, ARRAY_SIZE(buf));
@@ -68,9 +74,27 @@ int checkboard(void)
puts("SD card\n");
#endif
switch (sw) {
-
+#ifdef CONFIG_TARGET_LS1088AQDS
case 0:
-
+ case 1:
+ case 2:
+ case 3:
+ case 4:
+ case 5:
+ case 6:
+ case 7:
+ printf("vBank: %d\n", sw);
+ break;
+ case 8:
+ puts("PromJet\n");
+ break;
+ case 15:
+ puts("IFCCard\n");
+ break;
+ case 14:
+#else
+ case 0:
+#endif
puts("QSPI:");
sw = QIXIS_READ(brdcfg[0]);
sw = (sw & QIXIS_QMAP_MASK) >> QIXIS_QMAP_SHIFT;
@@ -87,9 +111,15 @@ int checkboard(void)
break;
}
-
+#ifdef CONFIG_TARGET_LS1088AQDS
+ printf("FPGA: v%d (%s), build %d",
+ (int)QIXIS_READ(scver), qixis_read_tag(buf),
+ (int)qixis_read_minor());
+ /* the timestamp string contains "\n" at the end */
+ printf(" on %s", qixis_read_time(buf));
+#else
printf("CPLD: v%d.%d\n", QIXIS_READ(scver), QIXIS_READ(tagdata));
-
+#endif
/*
* Display the actual SERDES reference clocks as configured by the
@@ -117,10 +147,13 @@ int checkboard(void)
bool if_board_diff_clk(void)
{
-
+#ifdef CONFIG_TARGET_LS1088AQDS
+ u8 diff_conf = QIXIS_READ(brdcfg[11]);
+ return diff_conf & 0x40;
+#else
u8 diff_conf = QIXIS_READ(dutcfg[11]);
return diff_conf & 0x80;
-
+#endif
}
unsigned long get_board_sys_clk(void)
@@ -220,7 +253,45 @@ void board_retimer_init(void)
reg |= 0x70;
i2c_write(I2C_RETIMER_ADDR, 0x2F, 1, ®, 1);
+#ifdef CONFIG_TARGET_LS1088AQDS
+ /* Retimer is connected to I2C1_CH5 */
+ select_i2c_ch_pca9547(I2C_MUX_CH5);
+
+ /* Access to Control/Shared register */
+ reg = 0x0;
+ i2c_write(I2C_RETIMER_ADDR2, 0xff, 1, ®, 1);
+
+ /* Read device revision and ID */
+ i2c_read(I2C_RETIMER_ADDR2, 1, 1, ®, 1);
+ debug("Retimer version id = 0x%x\n", reg);
+ /* Enable Broadcast. All writes target all channel register sets */
+ reg = 0x0c;
+ i2c_write(I2C_RETIMER_ADDR2, 0xff, 1, ®, 1);
+
+ /* Reset Channel Registers */
+ i2c_read(I2C_RETIMER_ADDR2, 0, 1, ®, 1);
+ reg |= 0x4;
+ i2c_write(I2C_RETIMER_ADDR2, 0, 1, ®, 1);
+
+ /* Set data rate as 10.3125 Gbps */
+ reg = 0x90;
+ i2c_write(I2C_RETIMER_ADDR2, 0x60, 1, ®, 1);
+ reg = 0xb3;
+ i2c_write(I2C_RETIMER_ADDR2, 0x61, 1, ®, 1);
+ reg = 0x90;
+ i2c_write(I2C_RETIMER_ADDR2, 0x62, 1, ®, 1);
+ reg = 0xb3;
+ i2c_write(I2C_RETIMER_ADDR2, 0x63, 1, ®, 1);
+ reg = 0xcd;
+ i2c_write(I2C_RETIMER_ADDR2, 0x64, 1, ®, 1);
+
+ /* Select VCO Divider to full rate (000) */
+ i2c_read(I2C_RETIMER_ADDR2, 0x2F, 1, ®, 1);
+ reg &= 0x0f;
+ reg |= 0x70;
+ i2c_write(I2C_RETIMER_ADDR2, 0x2F, 1, ®, 1);
+#endif
/*return the default channel*/
select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
}
diff --git a/board/freescale/ls1088a/ls1088a_qixis.h b/board/freescale/ls1088a/ls1088a_qixis.h
index 9757d1b..4790461 100644
--- a/board/freescale/ls1088a/ls1088a_qixis.h
+++ b/board/freescale/ls1088a/ls1088a_qixis.h
@@ -31,4 +31,9 @@
#define QIXIS_SDCLK1_165 0x2
#define QIXIS_SDCLK1_100_SP 0x3
+#define BRDCFG4_EMISEL_MASK 0xE0
+#define BRDCFG4_EMISEL_SHIFT 5
+#define BRDCFG9_SFPTX_MASK 0x10
+#define BRDCFG9_SFPTX_SHIFT 4
+
#endif
diff --git a/configs/ls1088aqds_qspi_defconfig b/configs/ls1088aqds_qspi_defconfig
new file mode 100644
index 0000000..6fff149
--- /dev/null
+++ b/configs/ls1088aqds_qspi_defconfig
@@ -0,0 +1,29 @@
+CONFIG_ARM=y
+CONFIG_TARGET_LS1088AQDS=y
+# CONFIG_SYS_MALLOC_F is not set
+CONFIG_DM_SPI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1088a-qds"
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_OF_STDOUT_VIA_ALIAS=y
+CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4, QSPI_BOOT"
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_I2C=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_PING=y
+CONFIG_OF_CONTROL=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM=y
+CONFIG_SPI_FLASH=y
+CONFIG_NETDEVICES=y
+CONFIG_E1000=y
+CONFIG_SYS_NS16550=y
+CONFIG_FSL_DSPI=y
+CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_FSL_LS_PPA=y
diff --git a/include/configs/ls1088aqds.h b/include/configs/ls1088aqds.h
new file mode 100644
index 0000000..3547b0b
--- /dev/null
+++ b/include/configs/ls1088aqds.h
@@ -0,0 +1,414 @@
+/*
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __LS1088A_QDS_H
+#define __LS1088A_QDS_H
+
+#include "ls1088a_common.h"
+
+
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+
+
+#ifndef __ASSEMBLY__
+unsigned long get_board_sys_clk(void);
+unsigned long get_board_ddr_clk(void);
+#endif
+
+
+#if defined(CONFIG_QSPI_BOOT)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
+#define CONFIG_ENV_OFFSET 0x300000 /* 3MB */
+#define CONFIG_ENV_SECT_SIZE 0x40000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x300000)
+#define CONFIG_ENV_SECT_SIZE 0x20000
+#define CONFIG_ENV_SIZE 0x20000
+#endif
+
+#if defined(CONFIG_QSPI_BOOT)
+#define CONFIG_QIXIS_I2C_ACCESS
+#define SYS_NO_FLASH
+
+#undef CONFIG_CMD_IMLS
+#define CONFIG_SYS_CLK_FREQ 100000000
+#define CONFIG_DDR_CLK_FREQ 100000000
+#else
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
+#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
+#endif
+
+#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4)
+#define COUNTER_FREQUENCY 25000000 /* 25MHz */
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+
+#define CONFIG_DDR_SPD
+#define CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
+#define SPD_EEPROM_ADDRESS 0x51
+#define CONFIG_SYS_SPD_BUS_NUM 0
+
+
+/*
+ * IFC Definitions
+ */
+#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
+#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
+#define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(64*1024*1024)
+
+#define CONFIG_SYS_NOR0_CSPR \
+ (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR0_CSPR_EARLY \
+ (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR1_CSPR \
+ (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH1_BASE_PHYS) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR1_CSPR_EARLY \
+ (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH1_BASE_PHYS_EARLY) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12)
+#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
+ FTIM0_NOR_TEADC(0x5) | \
+ FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
+ FTIM1_NOR_TRAD_NOR(0x1a) |\
+ FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
+ FTIM2_NOR_TCH(0x4) | \
+ FTIM2_NOR_TWPH(0x0E) | \
+ FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3 0x04000000
+#define CONFIG_SYS_IFC_CCR 0x01000000
+
+#ifndef SYS_NO_FLASH
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\
+ CONFIG_SYS_FLASH_BASE + 0x40000000}
+#endif
+#endif
+
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_MAX_ECCPOS 256
+#define CONFIG_SYS_NAND_MAX_OOBFREE 2
+
+#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
+#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+ | CSPR_MSEL_NAND /* MSEL = NAND */ \
+ | CSPR_V)
+#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)
+
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
+ | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
+ | CSOR_NAND_PGS_2K /* Page Size = 2K */ \
+ | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
+ | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
+ FTIM0_NAND_TWP(0x18) | \
+ FTIM0_NAND_TWCHT(0x07) | \
+ FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
+ FTIM1_NAND_TWBE(0x39) | \
+ FTIM1_NAND_TRR(0x0e) | \
+ FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
+ FTIM2_NAND_TREH(0x0a) | \
+ FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3 0x0
+
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
+#define CONFIG_FSL_QIXIS
+#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
+#define QIXIS_LBMAP_SWITCH 6
+#define QIXIS_QMAP_MASK 0xe0
+#define QIXIS_QMAP_SHIFT 5
+#define QIXIS_LBMAP_MASK 0x0f
+#define QIXIS_LBMAP_SHIFT 0
+#define QIXIS_LBMAP_DFLTBANK 0x0e
+#define QIXIS_LBMAP_ALTBANK 0x2e
+#define QIXIS_LBMAP_SD 0x00
+#define QIXIS_LBMAP_SD_QSPI 0x0e
+#define QIXIS_LBMAP_QSPI 0x0e
+#define QIXIS_RCW_SRC_SD 0x40
+#define QIXIS_RCW_SRC_QSPI 0x62
+#define QIXIS_RST_CTL_RESET 0x41
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
+#define QIXIS_RST_FORCE_MEM 0x01
+#define QIXIS_STAT_PRES1 0xb
+#define QIXIS_SDID_MASK 0x07
+#define QIXIS_ESDHC_NO_ADAPTER 0x7
+
+#define CONFIG_SYS_FPGA_CSPR_EXT (0x0)
+#define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_GPCM \
+ | CSPR_V)
+#define SYS_FPGA_CSPR_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_GPCM \
+ | CSPR_V)
+
+#define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64*1024)
+#if defined(CONFIG_QSPI_BOOT)
+#define CONFIG_SYS_FPGA_CSOR CSOR_GPCM_ADM_SHIFT(0)
+#else
+#define CONFIG_SYS_FPGA_CSOR CSOR_GPCM_ADM_SHIFT(12)
+#endif
+/* QIXIS Timing parameters*/
+#define SYS_FPGA_CS_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
+ FTIM0_GPCM_TEADC(0x0e) | \
+ FTIM0_GPCM_TEAHC(0x0e))
+#define SYS_FPGA_CS_FTIM1 (FTIM1_GPCM_TACO(0xff) | \
+ FTIM1_GPCM_TRAD(0x3f))
+#define SYS_FPGA_CS_FTIM2 (FTIM2_GPCM_TCS(0xf) | \
+ FTIM2_GPCM_TCH(0xf) | \
+ FTIM2_GPCM_TWP(0x3E))
+#define SYS_FPGA_CS_FTIM3 0x0
+
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_FPGA_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CONFIG_SYS_FPGA_CSPR
+#define CONFIG_SYS_CSPR2_FINAL SYS_FPGA_CSPR_FINAL
+#define CONFIG_SYS_AMASK2 CONFIG_SYS_FPGA_AMASK
+#define CONFIG_SYS_CSOR2 CONFIG_SYS_FPGA_CSOR
+#define CONFIG_SYS_CS2_FTIM0 SYS_FPGA_CS_FTIM0
+#define CONFIG_SYS_CS2_FTIM1 SYS_FPGA_CS_FTIM1
+#define CONFIG_SYS_CS2_FTIM2 SYS_FPGA_CS_FTIM2
+#define CONFIG_SYS_CS2_FTIM3 SYS_FPGA_CS_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY
+#define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR_EARLY
+#define CONFIG_SYS_CSPR1_FINAL CONFIG_SYS_NOR1_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK_EARLY
+#define CONFIG_SYS_AMASK1_FINAL CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR3_EXT CONFIG_SYS_FPGA_CSPR_EXT
+#define CONFIG_SYS_CSPR3 CONFIG_SYS_FPGA_CSPR
+#define CONFIG_SYS_CSPR3_FINAL CONFIG_SYS_FPGA_CSPR_FINAL
+#define CONFIG_SYS_AMASK3 CONFIG_SYS_FPGA_AMASK
+#define CONFIG_SYS_CSOR3 CONFIG_SYS_FPGA_CSOR
+#define CONFIG_SYS_CS3_FTIM0 CONFIG_SYS_FPGA_CS_FTIM0
+#define CONFIG_SYS_CS3_FTIM1 CONFIG_SYS_FPGA_CS_FTIM1
+#define CONFIG_SYS_CS3_FTIM2 CONFIG_SYS_FPGA_CS_FTIM2
+#define CONFIG_SYS_CS3_FTIM3 CONFIG_SYS_FPGA_CS_FTIM3
+#endif
+
+#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
+
+/*
+ * I2C bus multiplexer
+ */
+#define I2C_MUX_PCA_ADDR_PRI 0x77
+#define I2C_MUX_PCA_ADDR_SEC 0x76 /* Secondary multiplexer */
+#define I2C_RETIMER_ADDR 0x18
+#define I2C_RETIMER_ADDR2 0x19
+#define I2C_MUX_CH_DEFAULT 0x8
+#define I2C_MUX_CH5 0xD
+
+/*
+* RTC configuration
+*/
+#define RTC
+#define CONFIG_RTC_PCF8563 1
+#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/
+#define CONFIG_CMD_DATE
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+
+/* QSPI device */
+#if defined(CONFIG_QSPI_BOOT)
+#define CONFIG_FSL_QSPI
+#define CONFIG_SPI_FLASH_SPANSION
+#define FSL_QSPI_FLASH_SIZE (1 << 26)
+#define FSL_QSPI_FLASH_NUM 2
+
+#endif
+
+#ifdef CONFIG_FSL_DSPI
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_SPI_FLASH_EON
+#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_SF_DEFAULT_BUS 1
+#define CONFIG_SF_DEFAULT_CS 0
+#endif
+#endif
+
+#define CONFIG_CMD_MEMINFO
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START 0x80000000
+#define CONFIG_SYS_MEMTEST_END 0x9fffffff
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+
+#define CONFIG_FSL_MEMAC
+
+/* MMC */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
+#define CONFIG_ESDHC_DETECT_QUIRK ((readb(QIXIS_BASE + QIXIS_STAT_PRES1) & \
+ QIXIS_SDID_MASK) != QIXIS_ESDHC_NO_ADAPTER)
+
+/* Initial environment variables */
+#if defined(CONFIG_QSPI_BOOT)
+#undef CONFIG_EXTRA_ENV_SETTINGS
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:bank_intlv=auto\0" \
+ "loadaddr=0x90100000\0" \
+ "kernel_addr=0x100000\0" \
+ "ramdisk_addr=0x800000\0" \
+ "ramdisk_size=0x2000000\0" \
+ "fdt_high=0xa0000000\0" \
+ "initrd_high=0xffffffffffffffff\0" \
+ "kernel_start=0x1000000\0" \
+ "kernel_load=0xa0000000\0" \
+ "kernel_size=0x2800000\0" \
+ "mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \
+ "sf read 0x80100000 0xE00000 0x100000;" \
+ "fsl_mc start mc 0x80000000 0x80100000\0" \
+ "mcmemsize=0x70000000 \0"
+#else /* NOR BOOT */
+#undef CONFIG_EXTRA_ENV_SETTINGS
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:bank_intlv=auto\0" \
+ "loadaddr=0x90100000\0" \
+ "kernel_addr=0x100000\0" \
+ "ramdisk_addr=0x800000\0" \
+ "ramdisk_size=0x2000000\0" \
+ "fdt_high=0xa0000000\0" \
+ "initrd_high=0xffffffffffffffff\0" \
+ "kernel_start=0x1000000\0" \
+ "kernel_load=0xa0000000\0" \
+ "kernel_size=0x2800000\0" \
+ "mcinitcmd=fsl_mc start mc 0x580A00000 0x580E00000\0" \
+ "mcmemsize=0x70000000 \0"
+#endif
+
+#ifdef CONFIG_FSL_MC_ENET
+#define CONFIG_FSL_MEMAC
+#define CONFIG_PHYLIB
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_VITESSE
+#define CONFIG_PHY_REALTEK
+#define CONFIG_PHY_TERANETICS
+#define RGMII_PHY1_ADDR 0x1
+#define RGMII_PHY2_ADDR 0x2
+#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
+#define SGMII_CARD_PORT2_PHY_ADDR 0x1d
+#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
+#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
+
+#define XQSGMII_CARD_PHY1_PORT0_ADDR 0x0
+#define XQSGMII_CARD_PHY1_PORT1_ADDR 0x1
+#define XQSGMII_CARD_PHY1_PORT2_ADDR 0x2
+#define XQSGMII_CARD_PHY1_PORT3_ADDR 0x3
+#define XQSGMII_CARD_PHY2_PORT0_ADDR 0x4
+#define XQSGMII_CARD_PHY2_PORT1_ADDR 0x5
+#define XQSGMII_CARD_PHY2_PORT2_ADDR 0x6
+#define XQSGMII_CARD_PHY2_PORT3_ADDR 0x7
+#define XQSGMII_CARD_PHY3_PORT0_ADDR 0x8
+#define XQSGMII_CARD_PHY3_PORT1_ADDR 0x9
+#define XQSGMII_CARD_PHY3_PORT2_ADDR 0xa
+#define XQSGMII_CARD_PHY3_PORT3_ADDR 0xb
+#define XQSGMII_CARD_PHY4_PORT0_ADDR 0xc
+#define XQSGMII_CARD_PHY4_PORT1_ADDR 0xd
+#define XQSGMII_CARD_PHY4_PORT2_ADDR 0xe
+#define XQSGMII_CARD_PHY4_PORT3_ADDR 0xf
+
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_ETHPRIME "DPMAC1 at xgmii"
+#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
+
+#endif
+
+#undef CONFIG_CMDLINE_EDITING
+#include <config_distro_defaults.h>
+#define BOOT_TARGET_DEVICES(func) \
+ func(USB, usb, 0) \
+ func(MMC, mmc, 0) \
+ func(SCSI, scsi, 0) \
+ func(DHCP, dhcp, na)
+#include <config_distro_bootcmd.h>
+
+#include <asm/fsl_secure_boot.h>
+
+#endif /* __LS1088A_QDS_H */
--
2.7.4
More information about the U-Boot
mailing list