[U-Boot] [PATCH 2/2] ARM: Add a new arch + board for QEMU's 'virt' machine
Bin Meng
bmeng.cn at gmail.com
Thu Aug 31 06:55:55 UTC 2017
Hi Tuomas,
On Wed, Aug 30, 2017 at 4:31 PM, Tuomas Tynkkynen
<tuomas.tynkkynen at iki.fi> wrote:
> This board builds an U-Boot binary that is bootable with QEMU's 'virt'
> machine on ARM. The minimal QEMU command line is:
>
> qemu-system-arm -machine virt,highmem=off -bios u-boot.bin
>
> (Note that the 'highmem=off' parameter to the 'virt' machine is required for
> PCI to work in U-Boot.) This command line enables the following:
> - u-boot.bin loaded and executing in the emulated flash at address 0x0
> - A generated device tree blob placed at the start of RAM
> - A freely configurable amount of RAM, described by the DTB
> - A PL011 serial port, discoverable via the DTB
> - An ARMv7 architected timer
> - PSCI for rebooting the system
> - A generic ECAM-based PCI host controller, discoverable via the DTB
>
> Additionally, QEMU allows plugging a bunch of useful peripherals to the PCI bus.
> The following ones are supported by both U-Boot and Linux:
>
> - To enable a Serial ATA disk via an Intel ICH9 AHCI controller, pass e.g.:
> -drive if=none,file=disk.img,id=mydisk -device ich9-ahci,id=ahci -device ide-drive,drive=mydisk,bus=ahci.0
> - To enable an Intel E1000 network adapter, pass e.g.:
> -net nic,model=e1000 -net user
> - To add an EHCI-compliant USB host controller, pass e.g.:
> -device usb-ehci,id=ehci
Can we enable the NVMe driver (CONFIG_NVME) here?
>
> Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen at iki.fi>
> ---
> arch/arm/Kconfig | 10 ++++++++
> arch/arm/mach-qemu/Kconfig | 9 +++++++
> board/qemu-arm/Makefile | 5 ++++
> board/qemu-arm/qemu-arm.c | 35 ++++++++++++++++++++++++++
> configs/qemu_arm_defconfig | 27 ++++++++++++++++++++
> include/configs/qemu-arm.h | 63 ++++++++++++++++++++++++++++++++++++++++++++++
> 6 files changed, 149 insertions(+)
> create mode 100644 arch/arm/mach-qemu/Kconfig
> create mode 100644 board/qemu-arm/Makefile
> create mode 100644 board/qemu-arm/qemu-arm.c
> create mode 100644 configs/qemu_arm_defconfig
> create mode 100644 include/configs/qemu-arm.h
>
> diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
> index 53d0831935..0d01ba1b73 100644
> --- a/arch/arm/Kconfig
> +++ b/arch/arm/Kconfig
> @@ -630,6 +630,14 @@ config ARCH_MX5
> select CPU_V7
> select BOARD_EARLY_INIT_F
>
> +config ARCH_QEMU
> + bool "QEMU Virtual Platform"
> + select CPU_V7
> + select ARCH_SUPPORT_PSCI
> + select DM
> + select DM_SERIAL
> + select OF_CONTROL
> +
> config ARCH_RMOBILE
> bool "Renesas ARM SoCs"
> select DM
> @@ -1149,6 +1157,8 @@ source "arch/arm/mach-stm32/Kconfig"
>
> source "arch/arm/mach-sunxi/Kconfig"
>
> +source "arch/arm/mach-qemu/Kconfig"
> +
Can you insert this by following alphabetical order?
> source "arch/arm/mach-tegra/Kconfig"
>
> source "arch/arm/mach-uniphier/Kconfig"
> diff --git a/arch/arm/mach-qemu/Kconfig b/arch/arm/mach-qemu/Kconfig
> new file mode 100644
> index 0000000000..89d2a36719
> --- /dev/null
> +++ b/arch/arm/mach-qemu/Kconfig
> @@ -0,0 +1,9 @@
> +if ARCH_QEMU
> +
> +config SYS_BOARD
> + default "qemu-arm"
> +
> +config SYS_CONFIG_NAME
> + default "qemu-arm"
> +
> +endif
> diff --git a/board/qemu-arm/Makefile b/board/qemu-arm/Makefile
> new file mode 100644
> index 0000000000..3e9907d983
> --- /dev/null
> +++ b/board/qemu-arm/Makefile
Can this new board be put into the board/emulation/qemu-arm directory?
Since qemu-x86 is put there.
> @@ -0,0 +1,5 @@
> +#
> +# SPDX-License-Identifier: GPL-2.0
> +#
> +
> +obj-y += qemu-arm.o
> diff --git a/board/qemu-arm/qemu-arm.c b/board/qemu-arm/qemu-arm.c
> new file mode 100644
> index 0000000000..90d7badbf4
> --- /dev/null
> +++ b/board/qemu-arm/qemu-arm.c
> @@ -0,0 +1,35 @@
> +/*
> + * Copyright (c) 2017 Tuomas Tynkkynen
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +#include <common.h>
> +#include <fdtdec.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
This is not needed as gd is not referenced in this file.
> +
> +int board_init(void)
> +{
> + return 0;
> +}
> +
> +int dram_init(void)
> +{
> + if (fdtdec_setup_memory_size() != 0)
> + return -EINVAL;
> +
> + return 0;
> +}
> +
> +int dram_init_banksize(void)
> +{
> + fdtdec_setup_memory_banksize();
> +
> + return 0;
> +}
> +
> +void *board_fdt_blob_setup(void)
> +{
> + /* QEMU loads a generated DTB for us at the start of RAM. */
> + return (void *)CONFIG_SYS_SDRAM_BASE;
> +}
> diff --git a/configs/qemu_arm_defconfig b/configs/qemu_arm_defconfig
> new file mode 100644
> index 0000000000..d34512dd0d
> --- /dev/null
> +++ b/configs/qemu_arm_defconfig
> @@ -0,0 +1,27 @@
> +CONFIG_ARM=y
> +CONFIG_ARM_SMCCC=y
> +CONFIG_ARCH_QEMU=y
> +CONFIG_AHCI=y
> +CONFIG_DISTRO_DEFAULTS=y
> +# CONFIG_DISPLAY_CPUINFO is not set
> +# CONFIG_DISPLAY_BOARDINFO is not set
> +# CONFIG_CMD_IMLS is not set
> +CONFIG_CMD_PCI=y
> +CONFIG_CMD_USB=y
> +CONFIG_OF_BOARD=y
> +CONFIG_AHCI_PCI=y
> +CONFIG_BLK=y
> +# CONFIG_MMC is not set
> +CONFIG_DM_ETH=y
> +CONFIG_E1000=y
> +CONFIG_PCI=y
> +CONFIG_DM_PCI=y
> +CONFIG_PCIE_ECAM_GENERIC=y
> +CONFIG_SCSI=y
> +CONFIG_DM_SCSI=y
> +CONFIG_SYSRESET=y
> +CONFIG_SYSRESET_PSCI=y
> +CONFIG_USB=y
> +CONFIG_DM_USB=y
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_EHCI_PCI=y
> diff --git a/include/configs/qemu-arm.h b/include/configs/qemu-arm.h
> new file mode 100644
> index 0000000000..2bcc0efad0
> --- /dev/null
> +++ b/include/configs/qemu-arm.h
> @@ -0,0 +1,63 @@
> +/*
> + * Copyright (c) 2017 Tuomas Tynkkynen
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +#include <linux/sizes.h>
> +
> +/* Physical memory map */
> +#define CONFIG_SYS_TEXT_BASE 0x00000000
> +
> +#define CONFIG_NR_DRAM_BANKS 1
> +#define CONFIG_SYS_SDRAM_BASE 0x40000000
> +
> +/* The DTB generated by QEMU is placed at start of RAM, stay away from there */
> +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_2M)
> +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_2M)
> +#define CONFIG_SYS_MALLOC_LEN SZ_16M
> +
> +/* QEMU's PL011 serial port is detected via FDT using the device model */
> +#define CONFIG_PL01X_SERIAL
> +
> +/* QEMU implements a 62.5MHz architected timer */
> +/* FIXME: can we rely on CNTFREQ instead of hardcoding this fact here? */
> +#define CONFIG_SYS_ARCH_TIMER
> +#define CONFIG_SYS_HZ 1000
> +#define CONFIG_SYS_HZ_CLOCK 62500000
> +
> +/* Command prompt options */
> +#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
> +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
> + sizeof(CONFIG_SYS_PROMPT) + 16)
> +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
> +#define CONFIG_SYS_MAXARGS 64 /* max command args */
> +
> +/* For block devices, QEMU emulates an ICH9 AHCI controller over PCI */
> +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 8
> +#define CONFIG_SCSI_AHCI
> +#define CONFIG_LIBATA
> +
> +/* Environment options */
> +#define CONFIG_ENV_SIZE SZ_64K
> +
> +#include <config_distro_defaults.h>
> +
> +#define BOOT_TARGET_DEVICES(func) \
> + func(SCSI, scsi, 0)
> +
> +#include <config_distro_bootcmd.h>
> +
> +#define CONFIG_PREBOOT "pci enum"
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> + "fdt_addr=0x40000000\0" \
> + "scriptaddr=0x40200000\0" \
> + "pxefile_addr_r=0x40300000\0" \
> + "kernel_addr_r=0x40400000\0" \
> + "ramdisk_addr_r=0x44000000\0" \
> + BOOTENV
> +
> +#endif /* __CONFIG_H */
> --
Regards,
Bin
More information about the U-Boot
mailing list