[U-Boot] [PATCH v3 2/7] arm: usb: dra7xx: xHCI registers based on USB port index

[Marek Vasut]

On 02/19/2017 04:15 PM, Tom Rini wrote:
> On Sun, Feb 19, 2017 at 04:13:02PM +0100, Marek Vasut wrote:
>> On 02/19/2017 03:55 PM, Uri Mashiach wrote:
>>>
>>>
>>> On 02/19/2017 04:27 PM, Marek Vasut wrote:
>>>> On 02/19/2017 02:27 PM, Uri Mashiach wrote:
>>>>> Modify the determination of the base address of xHCI registers of DRA7XX
>>>>> targets.
>>>>> Before the commit: by the target.
>>>>> After the commit: by the USB port index.
>>>>>
>>>>> Cc: Lokesh Vutla <lokeshvutla at ti.com>
>>>>> Cc: Marek Vasut <marex at denx.de>
>>>>> Signed-off-by: Uri Mashiach <uri.mashiach at compulab.co.il>
>>>>> ---
>>>>> V1 -> V2: Replace the commit "fix XHCI registers base address".
>>>>> V2 -> V3: Replace the commit "reintroduce the CONFIG_AM57XX symbol"
>>>>>
>>>>>  configs/dra7xx_evm_defconfig    |  1 +
>>>>>  configs/dra7xx_hs_evm_defconfig |  1 +
>>>>>  drivers/usb/host/Kconfig        | 16 ++++++++++++++++
>>>>>  include/linux/usb/xhci-omap.h   |  6 ++++--
>>>>>  4 files changed, 22 insertions(+), 2 deletions(-)
>>>>>
>>>>> diff --git a/configs/dra7xx_evm_defconfig b/configs/dra7xx_evm_defconfig
>>>>> index 26b26cc..1f47f92 100644
>>>
>>> [...]
>>>
>>>>> diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
>>>>> index 5129a57..440fbcf 100644
>>>>> --- a/drivers/usb/host/Kconfig
>>>>> +++ b/drivers/usb/host/Kconfig
>>>>> @@ -43,6 +43,22 @@ config USB_XHCI_ZYNQMP
>>>>>      help
>>>>>        Enables support for the on-chip xHCI controller on Xilinx
>>>>> ZynqMP SoCs.
>>>>>
>>>>> +choice
>>>>> +    prompt "DRA7XX xHCI USB index select"
>>>>> +    depends on DRA7XX
>>>>> +
>>>>> +config USB_XHCI_DRA7XX_INDEX0
>>>>> +    bool "USB0"
>>>>> +    help
>>>>> +      DRA7XX xHCI USB0.
>>>>> +
>>>>> +config USB_XHCI_DRA7XX_INDEX1
>>>>> +    bool "USB1"
>>>>> +    help
>>>>> +      DRA7XX xHCI USB1.
>>>>
>>>> What is this all about ? Shouldn't this come from DT ? And what if I
>>>> want to use both XHCI ? This looks totally bogus ...
>>>>
>>>
>>> The support for both XHCI is currently missing.
>>> This could be a temporary solution until the DT solution.
>>> The current situation is worse - selecting USB0 or USB1 based on the
>>> target.
>>
>> So we're replacing it with equally bad solution ? Hmmm , no.
>> The MW will open mid-march, there's about a month to fix this,
>> so please do.
> 
> Do note that the relevant driver here is not yet using DM_USB.
> 
We had multi-controller support before DM existed, no problem.
But then, xhci does support DM, so fixing this should also not
be a problem.

-- 
Best regards,
Marek Vasut