[U-Boot] [PATCH 1/1] mmc: Add MMC support for stm32h7 Socs
Patrice CHOTARD
patrice.chotard at st.com
Wed Jul 19 07:29:00 UTC 2017
Fyi, a v2 has been send to add missing .get_cd() callback support
Patrice
On 07/17/2017 11:55 AM, patrice.chotard at st.com wrote:
> From: Patrice Chotard <patrice.chotard at st.com>
>
> This patch adds SD/MMC support for STM32H7 SoCs.
>
> Here is an extraction of SDMMC main features, embedded in
> STM32H7 SoCs.
> The SD/MMC block include the following:
> _ Full compliance with MultiMediaCard System Specification
> Version 4.51. Card support for three different databus modes:
> 1-bit (default), 4-bit and 8-bit.
> _ Full compatibility with previous versions of MultiMediaCards
> (backward compatibility).
> _ Full compliance with SD memory card specifications version 4.1.
> (SDR104 SDMMC_CK speed limited to maximum allowed IO speed,
> SPI mode and UHS-II mode not supported).
> _ Full compliance with SDIO card specification version 4.0.
> Card support for two different databus modes: 1-bit (default)
> and 4-bit. (SDR104 SDMMC_CK speed limited to maximum allowed IO
> speed, SPI mode and UHS-II mode not supported).
> _ Data transfer up to 208 Mbyte/s for the 8 bit mode.
> (depending maximum allowed IO speed).
> _ Data and command output enable signals to control external
> bidirectional drivers.
>
> The current version of the SDMMC supports only one SD/SDIO/MMC card
> at any one time and a stack of MMC Version 4.51 or previous.
>
> Signed-off-by: Christophe Kerello <christophe.kerello at st.com>
> Signed-off-by: Patrice Chotard <patrice.chotard at st.com>
> ---
> drivers/mmc/Kconfig | 8 +
> drivers/mmc/Makefile | 1 +
> drivers/mmc/stm32_sdmmc2.c | 601 +++++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 610 insertions(+)
> create mode 100644 drivers/mmc/stm32_sdmmc2.c
>
> diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig
> index 82b8d75..f2e4c26 100644
> --- a/drivers/mmc/Kconfig
> +++ b/drivers/mmc/Kconfig
> @@ -377,6 +377,14 @@ config GENERIC_ATMEL_MCI
> the SD Memory Card Specification V2.0, the SDIO V2.0 specification
> and CE-ATA V1.1.
>
> +config STM32_SDMMC2
> + bool "STMicroelectronics STM32H7 SD/MMC Host Controller support"
> + depends on DM_MMC && OF_CONTROL && DM_MMC_OPS
> + help
> + This selects support for the SD/MMC controller on STM32H7 SoCs.
> + If you have a board based on such a SoC and with a SD/MMC slot,
> + say Y or M here.
> +
> endif
>
> config TEGRA124_MMC_DISABLE_EXT_LOOPBACK
> diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile
> index 2d781c3..2584663 100644
> --- a/drivers/mmc/Makefile
> +++ b/drivers/mmc/Makefile
> @@ -43,6 +43,7 @@ obj-$(CONFIG_SUPPORT_EMMC_RPMB) += rpmb.o
> obj-$(CONFIG_MMC_SANDBOX) += sandbox_mmc.o
> obj-$(CONFIG_SH_MMCIF) += sh_mmcif.o
> obj-$(CONFIG_SH_SDHI) += sh_sdhi.o
> +obj-$(CONFIG_STM32_SDMMC2) += stm32_sdmmc2.o
>
> # SDHCI
> obj-$(CONFIG_MMC_SDHCI) += sdhci.o
> diff --git a/drivers/mmc/stm32_sdmmc2.c b/drivers/mmc/stm32_sdmmc2.c
> new file mode 100644
> index 0000000..12c4642
> --- /dev/null
> +++ b/drivers/mmc/stm32_sdmmc2.c
> @@ -0,0 +1,601 @@
> +/*
> + * Copyright (c) 2017 STMicrelectronics
> + *
> + * SPDX-License-Identifier: GPL-2.0
> + */
> +
> +#include <common.h>
> +#include <clk.h>
> +#include <dm.h>
> +#include <fdtdec.h>
> +#include <libfdt.h>
> +#include <mmc.h>
> +#include <reset.h>
> +#include <asm/io.h>
> +
> +struct stm32_sdmmc2 {
> + u32 power; /* SDMMC power control [0x00] */
> + u32 clkcr; /* SDMMC clock control [0x04] */
> + u32 arg; /* SDMMC argument [0x08] */
> + u32 cmd; /* SDMMC command [0x0C] */
> + u32 respcmd; /* SDMMC command response [0x10] */
> + u32 resp1; /* SDMMC response 1 [0x14] */
> + u32 resp2; /* SDMMC response 2 [0x18] */
> + u32 resp3; /* SDMMC response 3 [0x1C] */
> + u32 resp4; /* SDMMC response 4 [0x20] */
> + u32 dtimer; /* SDMMC data timer [0x24] */
> + u32 dlen; /* SDMMC data length [0x28] */
> + u32 dctrl; /* SDMMC data control [0x2C] */
> + u32 dcount; /* SDMMC data counter [0x30] */
> + u32 sta; /* SDMMC status [0x34] */
> + u32 icr; /* SDMMC interrupt clear [0x38] */
> + u32 mask; /* SDMMC mask [0x3C] */
> + u32 acktime; /* SDMMC Acknowledgment timer [0x40] */
> + u32 reserved0[3]; /* Reserved, 0x44 - 0x4C - 0x4C */
> + u32 idmactrl; /* SDMMC DMA control [0x50] */
> + u32 idmabsize; /* SDMMC DMA buffer size [0x54] */
> + u32 idmabase0; /* SDMMC DMA buffer 0 base address [0x58] */
> + u32 idmabase1; /* SDMMC DMA buffer 1 base address [0x5C] */
> + u32 reserved1[8]; /* Reserved, 0x4C-0x7C */
> + u32 fifo; /* SDMMC data FIFO [0x80] */
> +};
> +
> +struct stm32_sdmmc2_host {
> + struct stm32_sdmmc2 *base;
> + struct mmc_config cfg;
> + struct clk clk;
> + struct reset_ctl reset_ctl;
> + u32 clk_reg_add;
> + u32 pwr_reg_add;
> +};
> +
> +struct stm32_sdmmc2_ctx {
> + u32 cache_start;
> + u32 cache_end;
> + u32 data_length;
> + bool dpsm_abort;
> +};
> +
> +/* SDMMC_POWER register */
> +#define SDMMC_POWER_PWRCTRL GENMASK(1, 0)
> +#define SDMMC_POWER_VSWITCH BIT(2)
> +#define SDMMC_POWER_VSWITCHEN BIT(3)
> +#define SDMMC_POWER_DIRPOL BIT(4)
> +
> +/* SDMMC_CLKCR register */
> +#define SDMMC_CLKCR_CLKDIV GENMASK(9, 0)
> +#define SDMMC_CLKCR_CLKDIV_MAX SDMMC_CLKCR_CLKDIV
> +#define SDMMC_CLKCR_PWRSAV BIT(12)
> +#define SDMMC_CLKCR_WIDBUS_4 BIT(14)
> +#define SDMMC_CLKCR_WIDBUS_8 BIT(15)
> +#define SDMMC_CLKCR_NEGEDGE BIT(16)
> +#define SDMMC_CLKCR_HWFC_EN BIT(17)
> +#define SDMMC_CLKCR_DDR BIT(18)
> +#define SDMMC_CLKCR_BUSSPEED BIT(19)
> +#define SDMMC_CLKCR_SELCLKRX GENMASK(21, 20)
> +
> +/* SDMMC_CMD register */
> +#define SDMMC_CMD_CMDINDEX GENMASK(5, 0)
> +#define SDMMC_CMD_CMDTRANS BIT(6)
> +#define SDMMC_CMD_CMDSTOP BIT(7)
> +#define SDMMC_CMD_WAITRESP GENMASK(9, 8)
> +#define SDMMC_CMD_WAITRESP_0 BIT(8)
> +#define SDMMC_CMD_WAITRESP_1 BIT(9)
> +#define SDMMC_CMD_WAITINT BIT(10)
> +#define SDMMC_CMD_WAITPEND BIT(11)
> +#define SDMMC_CMD_CPSMEN BIT(12)
> +#define SDMMC_CMD_DTHOLD BIT(13)
> +#define SDMMC_CMD_BOOTMODE BIT(14)
> +#define SDMMC_CMD_BOOTEN BIT(15)
> +#define SDMMC_CMD_CMDSUSPEND BIT(16)
> +
> +/* SDMMC_DCTRL register */
> +#define SDMMC_DCTRL_DTEN BIT(0)
> +#define SDMMC_DCTRL_DTDIR BIT(1)
> +#define SDMMC_DCTRL_DTMODE GENMASK(3, 2)
> +#define SDMMC_DCTRL_DBLOCKSIZE GENMASK(7, 4)
> +#define SDMMC_DCTRL_DBLOCKSIZE_SHIFT 4
> +#define SDMMC_DCTRL_RWSTART BIT(8)
> +#define SDMMC_DCTRL_RWSTOP BIT(9)
> +#define SDMMC_DCTRL_RWMOD BIT(10)
> +#define SDMMC_DCTRL_SDMMCEN BIT(11)
> +#define SDMMC_DCTRL_BOOTACKEN BIT(12)
> +#define SDMMC_DCTRL_FIFORST BIT(13)
> +
> +/* SDMMC_STA register */
> +#define SDMMC_STA_CCRCFAIL BIT(0)
> +#define SDMMC_STA_DCRCFAIL BIT(1)
> +#define SDMMC_STA_CTIMEOUT BIT(2)
> +#define SDMMC_STA_DTIMEOUT BIT(3)
> +#define SDMMC_STA_TXUNDERR BIT(4)
> +#define SDMMC_STA_RXOVERR BIT(5)
> +#define SDMMC_STA_CMDREND BIT(6)
> +#define SDMMC_STA_CMDSENT BIT(7)
> +#define SDMMC_STA_DATAEND BIT(8)
> +#define SDMMC_STA_DHOLD BIT(9)
> +#define SDMMC_STA_DBCKEND BIT(10)
> +#define SDMMC_STA_DABORT BIT(11)
> +#define SDMMC_STA_DPSMACT BIT(12)
> +#define SDMMC_STA_CPSMACT BIT(13)
> +#define SDMMC_STA_TXFIFOHE BIT(14)
> +#define SDMMC_STA_RXFIFOHF BIT(15)
> +#define SDMMC_STA_TXFIFOF BIT(16)
> +#define SDMMC_STA_RXFIFOF BIT(17)
> +#define SDMMC_STA_TXFIFOE BIT(18)
> +#define SDMMC_STA_RXFIFOE BIT(19)
> +#define SDMMC_STA_BUSYD0 BIT(20)
> +#define SDMMC_STA_BUSYD0END BIT(21)
> +#define SDMMC_STA_SDMMCIT BIT(22)
> +#define SDMMC_STA_ACKFAIL BIT(23)
> +#define SDMMC_STA_ACKTIMEOUT BIT(24)
> +#define SDMMC_STA_VSWEND BIT(25)
> +#define SDMMC_STA_CKSTOP BIT(26)
> +#define SDMMC_STA_IDMATE BIT(27)
> +#define SDMMC_STA_IDMABTC BIT(28)
> +
> +/* SDMMC_ICR register */
> +#define SDMMC_ICR_CCRCFAILC BIT(0)
> +#define SDMMC_ICR_DCRCFAILC BIT(1)
> +#define SDMMC_ICR_CTIMEOUTC BIT(2)
> +#define SDMMC_ICR_DTIMEOUTC BIT(3)
> +#define SDMMC_ICR_TXUNDERRC BIT(4)
> +#define SDMMC_ICR_RXOVERRC BIT(5)
> +#define SDMMC_ICR_CMDRENDC BIT(6)
> +#define SDMMC_ICR_CMDSENTC BIT(7)
> +#define SDMMC_ICR_DATAENDC BIT(8)
> +#define SDMMC_ICR_DHOLDC BIT(9)
> +#define SDMMC_ICR_DBCKENDC BIT(10)
> +#define SDMMC_ICR_DABORTC BIT(11)
> +#define SDMMC_ICR_BUSYD0ENDC BIT(21)
> +#define SDMMC_ICR_SDMMCITC BIT(22)
> +#define SDMMC_ICR_ACKFAILC BIT(23)
> +#define SDMMC_ICR_ACKTIMEOUTC BIT(24)
> +#define SDMMC_ICR_VSWENDC BIT(25)
> +#define SDMMC_ICR_CKSTOPC BIT(26)
> +#define SDMMC_ICR_IDMATEC BIT(27)
> +#define SDMMC_ICR_IDMABTCC BIT(28)
> +#define SDMMC_ICR_STATIC_FLAGS ((GENMASK(28, 21)) | (GENMASK(11, 0)))
> +
> +/* SDMMC_MASK register */
> +#define SDMMC_MASK_CCRCFAILIE BIT(0)
> +#define SDMMC_MASK_DCRCFAILIE BIT(1)
> +#define SDMMC_MASK_CTIMEOUTIE BIT(2)
> +#define SDMMC_MASK_DTIMEOUTIE BIT(3)
> +#define SDMMC_MASK_TXUNDERRIE BIT(4)
> +#define SDMMC_MASK_RXOVERRIE BIT(5)
> +#define SDMMC_MASK_CMDRENDIE BIT(6)
> +#define SDMMC_MASK_CMDSENTIE BIT(7)
> +#define SDMMC_MASK_DATAENDIE BIT(8)
> +#define SDMMC_MASK_DHOLDIE BIT(9)
> +#define SDMMC_MASK_DBCKENDIE BIT(10)
> +#define SDMMC_MASK_DABORTIE BIT(11)
> +#define SDMMC_MASK_TXFIFOHEIE BIT(14)
> +#define SDMMC_MASK_RXFIFOHFIE BIT(15)
> +#define SDMMC_MASK_RXFIFOFIE BIT(17)
> +#define SDMMC_MASK_TXFIFOEIE BIT(18)
> +#define SDMMC_MASK_BUSYD0ENDIE BIT(21)
> +#define SDMMC_MASK_SDMMCITIE BIT(22)
> +#define SDMMC_MASK_ACKFAILIE BIT(23)
> +#define SDMMC_MASK_ACKTIMEOUTIE BIT(24)
> +#define SDMMC_MASK_VSWENDIE BIT(25)
> +#define SDMMC_MASK_CKSTOPIE BIT(26)
> +#define SDMMC_MASK_IDMABTCIE BIT(28)
> +
> +/* SDMMC_IDMACTRL register */
> +#define SDMMC_IDMACTRL_IDMAEN BIT(0)
> +
> +#define SDMMC_CMD_TIMEOUT 0xFFFFFFFF
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +static void stm32_sdmmc2_start_data(struct mmc *mmc, struct mmc_data *data,
> + struct stm32_sdmmc2_ctx *ctx)
> +{
> + struct stm32_sdmmc2_host *host = mmc->priv;
> + struct stm32_sdmmc2 *sdmmc_handler = host->base;
> + u32 data_ctrl, idmabase0;
> +
> + /* Configure the SDMMC DPSM (Data Path State Machine) */
> + data_ctrl = (__ilog2(data->blocksize) <<
> + SDMMC_DCTRL_DBLOCKSIZE_SHIFT) &
> + SDMMC_DCTRL_DBLOCKSIZE;
> +
> + if (data->flags & MMC_DATA_READ) {
> + data_ctrl |= SDMMC_DCTRL_DTDIR;
> + idmabase0 = (u32)data->dest;
> + } else {
> + idmabase0 = (u32)data->src;
> + }
> +
> + /* Set the SDMMC Data TimeOut value */
> + writel(SDMMC_CMD_TIMEOUT, &sdmmc_handler->dtimer);
> +
> + /* Set the SDMMC DataLength value */
> + writel(ctx->data_length, &sdmmc_handler->dlen);
> +
> + /* Write to SDMMC DCTRL */
> + writel(data_ctrl, &sdmmc_handler->dctrl);
> +
> + /* Cache align */
> + ctx->cache_start = rounddown(idmabase0, ARCH_DMA_MINALIGN);
> + ctx->cache_end = roundup(idmabase0 + ctx->data_length,
> + ARCH_DMA_MINALIGN);
> +
> + /*
> + * Flush data cache before DMA start (clean and invalidate)
> + * Clean also needed for read
> + * Avoid issue on buffer not cached-aligned
> + */
> + flush_dcache_range(ctx->cache_start, ctx->cache_end);
> +
> + /* Enable internal DMA */
> + writel(idmabase0, &sdmmc_handler->idmabase0);
> + writel(SDMMC_IDMACTRL_IDMAEN, &sdmmc_handler->idmactrl);
> +}
> +
> +static void stm32_sdmmc2_start_cmd(struct mmc *mmc, struct mmc_cmd *cmd, u32 c)
> +{
> + struct stm32_sdmmc2_host *host = mmc->priv;
> + struct stm32_sdmmc2 *sdmmc_handler = host->base;
> +
> + if (readl(&sdmmc_handler->arg) & SDMMC_CMD_CPSMEN)
> + writel(0, &sdmmc_handler->arg);
> +
> + c |= cmd->cmdidx | SDMMC_CMD_CPSMEN;
> + if (cmd->resp_type & MMC_RSP_PRESENT) {
> + if (cmd->resp_type & MMC_RSP_136)
> + c |= SDMMC_CMD_WAITRESP;
> + else if (cmd->resp_type & MMC_RSP_CRC)
> + c |= SDMMC_CMD_WAITRESP_0;
> + else
> + c |= SDMMC_CMD_WAITRESP_1;
> + }
> +
> + /* Clear flags */
> + writel(SDMMC_ICR_STATIC_FLAGS, &sdmmc_handler->icr);
> +
> + /* Set SDMMC argument value */
> + writel(cmd->cmdarg, &sdmmc_handler->arg);
> +
> + /* Set SDMMC command parameters */
> + writel(c, &sdmmc_handler->cmd);
> +}
> +
> +static int stm32_sdmmc2_end_cmd(struct mmc *mmc, struct mmc_cmd *cmd,
> + struct stm32_sdmmc2_ctx *ctx)
> +{
> + struct stm32_sdmmc2_host *host = mmc->priv;
> + struct stm32_sdmmc2 *sdmmc_handler = host->base;
> + u32 mask = SDMMC_STA_CTIMEOUT;
> + u32 status;
> +
> + if (cmd->resp_type & MMC_RSP_PRESENT) {
> + mask |= SDMMC_STA_CMDREND;
> + if (cmd->resp_type & MMC_RSP_CRC)
> + mask |= SDMMC_STA_CCRCFAIL;
> + } else {
> + mask |= SDMMC_STA_CMDSENT;
> + }
> +
> + /* Polling status register */
> + status = readl(&sdmmc_handler->sta);
> + while (!(status & mask))
> + status = readl(&sdmmc_handler->sta);
> +
> + /* Check status */
> + if (status & SDMMC_STA_CTIMEOUT) {
> + debug("%s: error SDMMC_STA_CTIMEOUT (0x%x) for cmd %d\n",
> + __func__, status, cmd->cmdidx);
> + ctx->dpsm_abort = true;
> + return -ETIMEDOUT;
> + }
> +
> + if (status & SDMMC_STA_CCRCFAIL && cmd->resp_type & MMC_RSP_CRC) {
> + debug("%s: error SDMMC_STA_CCRCFAIL (0x%x) for cmd %d\n",
> + __func__, status, cmd->cmdidx);
> + ctx->dpsm_abort = true;
> + return -EILSEQ;
> + }
> +
> + if (status & SDMMC_STA_CMDREND && cmd->resp_type & MMC_RSP_PRESENT) {
> + cmd->response[0] = readl(&sdmmc_handler->resp1);
> + if (cmd->resp_type & MMC_RSP_136) {
> + cmd->response[1] = readl(&sdmmc_handler->resp2);
> + cmd->response[2] = readl(&sdmmc_handler->resp3);
> + cmd->response[3] = readl(&sdmmc_handler->resp4);
> + }
> + }
> +
> + return 0;
> +}
> +
> +static int stm32_sdmmc2_end_data(struct mmc *mmc, struct mmc_cmd *cmd,
> + struct mmc_data *data,
> + struct stm32_sdmmc2_ctx *ctx)
> +{
> + struct stm32_sdmmc2_host *host = mmc->priv;
> + struct stm32_sdmmc2 *sdmmc_handler = host->base;
> + u32 mask = SDMMC_STA_DCRCFAIL | SDMMC_STA_DTIMEOUT |
> + SDMMC_STA_IDMATE | SDMMC_STA_DATAEND;
> + u32 status;
> +
> + if (data->flags & MMC_DATA_READ)
> + mask |= SDMMC_STA_RXOVERR;
> + else
> + mask |= SDMMC_STA_TXUNDERR;
> +
> + status = readl(&sdmmc_handler->sta);
> + while (!(status & mask))
> + status = readl(&sdmmc_handler->sta);
> +
> + /*
> + * Need invalidate the dcache again to avoid any
> + * cache-refill during the DMA operations (pre-fetching)
> + */
> + if (data->flags & MMC_DATA_READ)
> + invalidate_dcache_range(ctx->cache_start, ctx->cache_end);
> +
> + if (status & SDMMC_STA_DCRCFAIL) {
> + debug("%s: error SDMMC_STA_DCRCFAIL (0x%x) for cmd %d\n",
> + __func__, status, cmd->cmdidx);
> + if (readl(&sdmmc_handler->dcount))
> + ctx->dpsm_abort = true;
> + return -EILSEQ;
> + }
> +
> + if (status & SDMMC_STA_DTIMEOUT) {
> + debug("%s: error SDMMC_STA_DTIMEOUT (0x%x) for cmd %d\n",
> + __func__, status, cmd->cmdidx);
> + ctx->dpsm_abort = true;
> + return -ETIMEDOUT;
> + }
> +
> + if (status & SDMMC_STA_TXUNDERR) {
> + debug("%s: error SDMMC_STA_TXUNDERR (0x%x) for cmd %d\n",
> + __func__, status, cmd->cmdidx);
> + ctx->dpsm_abort = true;
> + return -EIO;
> + }
> +
> + if (status & SDMMC_STA_RXOVERR) {
> + debug("%s: error SDMMC_STA_RXOVERR (0x%x) for cmd %d\n",
> + __func__, status, cmd->cmdidx);
> + ctx->dpsm_abort = true;
> + return -EIO;
> + }
> +
> + if (status & SDMMC_STA_IDMATE) {
> + debug("%s: error SDMMC_STA_IDMATE (0x%x) for cmd %d\n",
> + __func__, status, cmd->cmdidx);
> + ctx->dpsm_abort = true;
> + return -EIO;
> + }
> +
> + return 0;
> +}
> +
> +static int stm32_sdmmc2_send_cmd(struct udevice *dev, struct mmc_cmd *cmd,
> + struct mmc_data *data)
> +{
> + struct mmc *mmc = mmc_get_mmc_dev(dev);
> + struct stm32_sdmmc2_host *host = mmc->priv;
> + struct stm32_sdmmc2 *sdmmc_handler = host->base;
> + struct stm32_sdmmc2_ctx ctx;
> + u32 cmdat = data ? SDMMC_CMD_CMDTRANS : 0;
> + int ret, retry = 3;
> +
> +retry_cmd:
> + ctx.data_length = 0;
> + ctx.dpsm_abort = false;
> +
> + if (data) {
> + ctx.data_length = data->blocks * data->blocksize;
> + stm32_sdmmc2_start_data(mmc, data, &ctx);
> + }
> +
> + stm32_sdmmc2_start_cmd(mmc, cmd, cmdat);
> +
> + debug("%s: send cmd %d data: 0x%x @ 0x%x\n",
> + __func__, cmd->cmdidx,
> + data ? ctx.data_length : 0, (unsigned int)data);
> +
> + ret = stm32_sdmmc2_end_cmd(mmc, cmd, &ctx);
> +
> + if (data && !ret)
> + ret = stm32_sdmmc2_end_data(mmc, cmd, data, &ctx);
> +
> + /* Clear flags */
> + writel(SDMMC_ICR_STATIC_FLAGS, &sdmmc_handler->icr);
> + if (data)
> + writel(0x0, &sdmmc_handler->idmactrl);
> +
> + /*
> + * To stop Data Path State Machine, a stop_transmission command
> + * shall be send on cmd or data errors.
> + */
> + if (ctx.dpsm_abort && (cmd->cmdidx != MMC_CMD_STOP_TRANSMISSION)) {
> + struct mmc_cmd stop_cmd;
> +
> + stop_cmd.cmdidx = MMC_CMD_STOP_TRANSMISSION;
> + stop_cmd.cmdarg = 0;
> + stop_cmd.resp_type = MMC_RSP_R1b;
> +
> + debug("%s: send STOP command to abort dpsm treatments\n",
> + __func__);
> +
> + stm32_sdmmc2_start_cmd(mmc, &stop_cmd, SDMMC_CMD_CMDSTOP);
> + stm32_sdmmc2_end_cmd(mmc, &stop_cmd, &ctx);
> +
> + writel(SDMMC_ICR_STATIC_FLAGS, &sdmmc_handler->icr);
> + }
> +
> + if ((ret != -ETIMEDOUT) && (ret != 0) && retry) {
> + printf("%s: cmd %d failed, retrying ...\n",
> + __func__, cmd->cmdidx);
> + retry--;
> + goto retry_cmd;
> + }
> +
> + debug("%s: end for CMD %d, ret = %d\n", __func__, cmd->cmdidx, ret);
> +
> + return ret;
> +}
> +
> +static void stm32_sdmmc2_pwron(struct stm32_sdmmc2_host *host)
> +{
> + struct stm32_sdmmc2 *sdmmc_handler = host->base;
> +
> + /* Reset */
> + reset_assert(&host->reset_ctl);
> + udelay(2);
> + reset_deassert(&host->reset_ctl);
> +
> + udelay(1000);
> +
> + /* Set Power State to ON */
> + writel(SDMMC_POWER_PWRCTRL | host->pwr_reg_add, &sdmmc_handler->power);
> +
> + /*
> + * 1ms: required power up waiting time before starting the
> + * SD initialization sequence
> + */
> + udelay(1000);
> +}
> +
> +#define IS_RISING_EDGE(reg) (reg & SDMMC_CLKCR_NEGEDGE ? 0 : 1)
> +static int stm32_sdmmc2_set_ios(struct udevice *dev)
> +{
> + struct mmc *mmc = mmc_get_mmc_dev(dev);
> + struct stm32_sdmmc2_host *host = mmc->priv;
> + struct stm32_sdmmc2 *sdmmc_handler = host->base;
> + struct mmc_config *cfg = &host->cfg;
> + u32 desired = mmc->clock;
> + u32 sys_clock = clk_get_rate(&host->clk);
> + u32 clk = 0;
> +
> + debug("%s: bus_with = %d, clock = %d\n", __func__,
> + mmc->bus_width, mmc->clock);
> +
> + if ((mmc->bus_width == 1) && (desired == cfg->f_min))
> + stm32_sdmmc2_pwron(host);
> +
> + /*
> + * clk_div = 0 => command and data generated on SDMMCCLK falling edge
> + * clk_div > 0 and NEGEDGE = 0 => command and data generated on
> + * SDMMCCLK rising edge
> + * clk_div > 0 and NEGEDGE = 1 => command and data generated on
> + * SDMMCCLK falling edge
> + */
> + if (desired && ((sys_clock > desired) ||
> + IS_RISING_EDGE(host->clk_reg_add))) {
> + clk = DIV_ROUND_UP(sys_clock, 2 * desired);
> + if (clk > SDMMC_CLKCR_CLKDIV_MAX)
> + clk = SDMMC_CLKCR_CLKDIV_MAX;
> + }
> +
> + if (mmc->bus_width == 4)
> + clk |= SDMMC_CLKCR_WIDBUS_4;
> + if (mmc->bus_width == 8)
> + clk |= SDMMC_CLKCR_WIDBUS_8;
> +
> + writel(clk | host->clk_reg_add, &sdmmc_handler->clkcr);
> +
> + return 0;
> +}
> +
> +static const struct dm_mmc_ops stm32_sdmmc2_ops = {
> + .send_cmd = stm32_sdmmc2_send_cmd,
> + .set_ios = stm32_sdmmc2_set_ios,
> +};
> +
> +static int stm32_sdmmc2_probe(struct udevice *dev)
> +{
> + struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
> + struct stm32_sdmmc2_host *host = dev_get_priv(dev);
> + struct mmc_config *cfg = &host->cfg;
> + struct mmc *mmc;
> + fdt_addr_t addr;
> + int ret;
> +
> + addr = devfdt_get_addr(dev);
> + if (addr == FDT_ADDR_T_NONE)
> + return -EINVAL;
> +
> + host->base = (struct stm32_sdmmc2 *)addr;
> +
> + if (dev_read_bool(dev, "st,negedge"))
> + host->clk_reg_add |= SDMMC_CLKCR_NEGEDGE;
> + if (dev_read_bool(dev, "st,dirpol"))
> + host->pwr_reg_add |= SDMMC_POWER_DIRPOL;
> +
> + ret = clk_get_by_index(dev, 0, &host->clk);
> + if (ret)
> + return ret;
> +
> + ret = clk_enable(&host->clk);
> + if (ret)
> + goto clk_free;
> +
> + ret = reset_get_by_index(dev, 0, &host->reset_ctl);
> + if (ret)
> + goto clk_disable;
> +
> + cfg->f_min = 400000;
> + cfg->f_max = dev_read_u32_default(dev, "max-frequency", 52000000);
> + cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34 | MMC_VDD_165_195;
> + cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT;
> + cfg->name = "STM32 SD/MMCv2";
> +
> + cfg->host_caps = 0;
> + if (cfg->f_max > 25000000)
> + cfg->host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS;
> +
> + switch (dev_read_u32_default(dev, "bus-width", 1)) {
> + case 8:
> + cfg->host_caps |= MMC_MODE_8BIT;
> + case 4:
> + cfg->host_caps |= MMC_MODE_4BIT;
> + break;
> + case 1:
> + break;
> + default:
> + printf("%s: invalid \"bus-width\" property\n", __func__);
> + ret = -ENOENT;
> + goto reset_free;
> + }
> +
> + mmc = mmc_create(cfg, host);
> + if (!mmc) {
> + ret = -ENOMEM;
> + goto reset_free;
> + }
> +
> + mmc->block_dev.removable = !dev_read_bool(dev, "non-removable");
> + mmc->dev = dev;
> + upriv->mmc = mmc;
> +
> + return 0;
> +
> +reset_free:
> + reset_free(&host->reset_ctl);
> +clk_disable:
> + clk_disable(&host->clk);
> +clk_free:
> + clk_free(&host->clk);
> +
> + return ret;
> +}
> +
> +static const struct udevice_id stm32_sdmmc2_ids[] = {
> + { .compatible = "st,stm32-sdmmc2" },
> + { }
> +};
> +
> +U_BOOT_DRIVER(stm32_sdmmc2) = {
> + .name = "stm32_sdmmc2",
> + .id = UCLASS_MMC,
> + .of_match = stm32_sdmmc2_ids,
> + .ops = &stm32_sdmmc2_ops,
> + .probe = stm32_sdmmc2_probe,
> + .priv_auto_alloc_size = sizeof(struct stm32_sdmmc2_host),
> +};
>
More information about the U-Boot
mailing list