[U-Boot] [PATCH v3 03/10] powerpc: spl and normal u-boot stage set SYS_MALLOC_F_LEN indepently

[Andy Yan]

Some platforms has very small sram to run spl code, so
it may have no enough sapce for so much malloc pool before
relocation in spl stage as the normal u-boot stage.
Use CONFIG_VAL(SYS_MALLOC_F_LEN) to fit this condition.

Signed-off-by: Andy Yan <andy.yan at rock-chips.com>

---

Changes in v3:
- use CONFIG_VAL(), which suggested by Simon

Changes in v2: None

 arch/powerpc/cpu/mpc83xx/start.S |  8 ++++----
 arch/powerpc/cpu/mpc85xx/start.S | 11 +++++------
 2 files changed, 9 insertions(+), 10 deletions(-)

diff --git a/arch/powerpc/cpu/mpc83xx/start.S b/arch/powerpc/cpu/mpc83xx/start.S
index 2fed4a1..1c3c737 100644
--- a/arch/powerpc/cpu/mpc83xx/start.S
+++ b/arch/powerpc/cpu/mpc83xx/start.S
@@ -274,14 +274,14 @@ in_flash:
 	cmplw	r3, r4
 	bne	1b
 
-#ifdef CONFIG_SYS_MALLOC_F_LEN
+#if CONFIG_VAL(SYS_MALLOC_F_LEN)
 
-#if CONFIG_SYS_MALLOC_F_LEN + GENERATED_GBL_DATA_SIZE > CONFIG_SYS_INIT_RAM_SIZE
-#error "CONFIG_SYS_MALLOC_F_LEN too large to fit into initial RAM."
+#if CONFIG_VAL(SYS_MALLOC_F_LEN) + GENERATED_GBL_DATA_SIZE > CONFIG_SYS_INIT_RAM_SIZE
+#error "SYS_MALLOC_F_LEN too large to fit into initial RAM."
 #endif
 
 	/* r3 = new stack pointer / pre-reloc malloc area */
-	subi    r3, r3, CONFIG_SYS_MALLOC_F_LEN
+	subi    r3, r3, CONFIG_VAL(SYS_MALLOC_F_LEN)
 
 	/* Set pointer to pre-reloc malloc area in GD */
 	stw     r3, GD_MALLOC_BASE(r4)
diff --git a/arch/powerpc/cpu/mpc85xx/start.S b/arch/powerpc/cpu/mpc85xx/start.S
index 63fdffd..58cb9fc 100644
--- a/arch/powerpc/cpu/mpc85xx/start.S
+++ b/arch/powerpc/cpu/mpc85xx/start.S
@@ -1183,14 +1183,13 @@ _start_cont:
 	lis	r3,(CONFIG_SYS_INIT_RAM_ADDR)@h
 	ori	r3,r3,((CONFIG_SYS_INIT_SP_OFFSET-16)&~0xf)@l /* Align to 16 */
 
-#ifdef CONFIG_SYS_MALLOC_F_LEN
-
-#if CONFIG_SYS_MALLOC_F_LEN + GENERATED_GBL_DATA_SIZE > CONFIG_SYS_INIT_RAM_SIZE
-#error "CONFIG_SYS_MALLOC_F_LEN too large to fit into initial RAM."
+#if CONFIG_VAL(SYS_MALLOC_F_LEN)
+#if CONFIG_VAL(SYS_MALLOC_F_LEN) + GENERATED_GBL_DATA_SIZE > CONFIG_SYS_INIT_RAM_SIZE
+#error "SYS_MALLOC_F_LEN too large to fit into initial RAM."
 #endif
 
 	/* Leave 16+ byte for back chain termination and NULL return address */
-	subi	r3,r3,((CONFIG_SYS_MALLOC_F_LEN+16+15)&~0xf)
+	subi	r3,r3,((CONFIG_VAL(SYS_MALLOC_F_LEN)+16+15)&~0xf)
 #endif
 
 	/* End of RAM */
@@ -1204,7 +1203,7 @@ _start_cont:
 	cmplw 	r4,r3
 	bne	1b
 
-#ifdef CONFIG_SYS_MALLOC_F_LEN
+#if CONFIG_VAL(SYS_MALLOC_F_LEN)
 	lis	r4,(CONFIG_SYS_INIT_RAM_ADDR)@h
 	ori	r4,r4,(CONFIG_SYS_GBL_DATA_OFFSET)@l
 
-- 
2.7.4