[U-Boot] [PATCH v3 5/8] sf: add 'addr_len' member to 'struct spi_flash'

[Wenyou Yang]

From: Cyrille Pitchen <cyrille.pitchen at atmel.com>

This is a transitional patch to prepare the SPI FLASH sub-system to
support the 4-byte address instruction set later.
For now, flash->addr_len is always set to SPI_FLASH_3B_ADDR_LEN.

Signed-off-by: Cyrille Pitchen <cyrille.pitchen at atmel.com>
Signed-off-by: Wenyou Yang <wenyou.yang at microchip.com>
---

Changes in v3: None
Changes in v2: None

 drivers/mtd/spi/spi_flash.c | 13 ++++++++-----
 include/spi_flash.h         |  2 ++
 2 files changed, 10 insertions(+), 5 deletions(-)

diff --git a/drivers/mtd/spi/spi_flash.c b/drivers/mtd/spi/spi_flash.c
index 8712e5eef0..d6942d57b2 100644
--- a/drivers/mtd/spi/spi_flash.c
+++ b/drivers/mtd/spi/spi_flash.c
@@ -322,7 +322,7 @@ int spi_flash_cmd_erase_ops(struct spi_flash *flash, u32 offset, size_t len)
 		}
 	}
 
-	spi_flash_command_init(&cmd, flash->erase_cmd, SPI_FLASH_3B_ADDR_LEN,
+	spi_flash_command_init(&cmd, flash->erase_cmd, flash->addr_len,
 			       SPI_FCMD_ERASE);
 	while (len) {
 		erase_addr = offset;
@@ -377,7 +377,7 @@ int spi_flash_cmd_write_ops(struct spi_flash *flash, u32 offset,
 		}
 	}
 
-	spi_flash_command_init(&cmd, flash->write_cmd, SPI_FLASH_3B_ADDR_LEN,
+	spi_flash_command_init(&cmd, flash->write_cmd, flash->addr_len,
 			       SPI_FCMD_WRITE);
 	cmd.proto = flash->write_proto;
 	for (actual = 0; actual < len; actual += chunk_len) {
@@ -481,7 +481,7 @@ int spi_flash_cmd_read_ops(struct spi_flash *flash, u32 offset,
 		return 0;
 	}
 
-	spi_flash_command_init(&cmd, flash->read_cmd, SPI_FLASH_3B_ADDR_LEN,
+	spi_flash_command_init(&cmd, flash->read_cmd, flash->addr_len,
 			       SPI_FCMD_READ);
 	cmd.proto = flash->read_proto;
 	cmd.num_wait_states = flash->dummy_byte * 8;
@@ -529,7 +529,7 @@ static int sst_byte_write(struct spi_flash *flash, u32 offset, const void *buf)
 	int ret;
 	u8 sr = 0xFFu;
 
-	spi_flash_command_init(&cmd, CMD_SST_BP, SPI_FLASH_3B_ADDR_LEN,
+	spi_flash_command_init(&cmd, CMD_SST_BP, flash->addr_len,
 			       SPI_FCMD_WRITE);
 	cmd.addr = offset;
 	cmd.data_len = 1;
@@ -580,7 +580,7 @@ int sst_write_wp(struct spi_flash *flash, u32 offset, size_t len,
 	if (ret)
 		goto done;
 
-	spi_flash_command_init(&cmd, CMD_SST_AAI_WP, SPI_FLASH_3B_ADDR_LEN,
+	spi_flash_command_init(&cmd, CMD_SST_AAI_WP, flash->addr_len,
 			       SPI_FCMD_WRITE);
 	cmd.addr = offset;
 	cmd.data_len = 2;
@@ -1102,6 +1102,9 @@ int spi_flash_scan(struct spi_flash *flash)
 		flash->flags |= SNOR_F_USE_FSR;
 #endif
 
+	/* Set the address length */
+	flash->addr_len = SPI_FLASH_3B_ADDR_LEN;
+
 	/* Configure the BAR - discover bank cmds and read current bank */
 #ifdef CONFIG_SPI_FLASH_BAR
 	ret = read_bar(flash, info);
diff --git a/include/spi_flash.h b/include/spi_flash.h
index 688a1708fd..09a81fdd76 100644
--- a/include/spi_flash.h
+++ b/include/spi_flash.h
@@ -45,6 +45,7 @@ struct spi_slave;
  * @bank_read_cmd:	Bank read cmd
  * @bank_write_cmd:	Bank write cmd
  * @bank_curr:		Current flash bank
+ * @addr_len:		Number of bytes for the address
  * @erase_cmd:		Erase cmd 4K, 32K, 64K
  * @read_cmd:		Read cmd - Array Fast, Extn read and quad read.
  * @write_cmd:		Write cmd - page and quad program.
@@ -82,6 +83,7 @@ struct spi_flash {
 	u8 bank_write_cmd;
 	u8 bank_curr;
 #endif
+	u8 addr_len;
 	u8 erase_cmd;
 	u8 read_cmd;
 	u8 write_cmd;
-- 
2.13.0