[U-Boot] [U-Boot, v2, 2/3] regulator: pbias: Add PBIAS regulator for proper voltage switching on MMC1
Jaehoon Chung
jh80.chung at samsung.com
Fri Jul 28 12:59:43 UTC 2017
On 07/19/2017 10:52 PM, Jean-Jacques Hiblot wrote:
> In the TI SOCs a PBIAS cell exists to provide a bias voltage to the MMC1
> IO cells. Without this bias voltage these I/O cells can not function
> properly. The PBIAS cell is controlled by software.
>
> Signed-off-by: Jean-Jacques Hiblot <jjhiblot at ti.com>
> Reviewed-by: Tom Rini <trini at konsulko.com>
> Reviewed-by: Simon Glass <sjg at chromium.org>
Applied to u-boot-mmc. Thanks!
Best Regards,
Jaehoon Chung
> ---
>
> changes since v1:
> - automatically select the PBIAS driver if DM_REGULATOR, DM_MMC and
> MMC_OMAP_HS are set
> - use the dev_read_*() API to access the DT
>
> drivers/mmc/Kconfig | 1 +
> drivers/power/regulator/Kconfig | 10 +
> drivers/power/regulator/Makefile | 1 +
> drivers/power/regulator/pbias_regulator.c | 302 ++++++++++++++++++++++++++++++
> 4 files changed, 314 insertions(+)
> create mode 100644 drivers/power/regulator/pbias_regulator.c
>
> diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig
> index 588e118..63e1122 100644
> --- a/drivers/mmc/Kconfig
> +++ b/drivers/mmc/Kconfig
> @@ -158,6 +158,7 @@ config MMC_PCI
> config MMC_OMAP_HS
> bool "TI OMAP High Speed Multimedia Card Interface support"
> select DM_MMC_OPS if DM_MMC
> + select DM_REGULATOR_PBIAS if DM_MMC && DM_REGULATOR
> help
> This selects the TI OMAP High Speed Multimedia card Interface.
> If you have an omap2plus board with a Multimedia Card slot,
> diff --git a/drivers/power/regulator/Kconfig b/drivers/power/regulator/Kconfig
> index f213487..f4ed3cc 100644
> --- a/drivers/power/regulator/Kconfig
> +++ b/drivers/power/regulator/Kconfig
> @@ -142,6 +142,16 @@ config DM_REGULATOR_PALMAS
> features for REGULATOR PALMAS and the family of PALMAS PMICs.
> The driver implements get/set api for: value and enable.
>
> +config DM_REGULATOR_PBIAS
> + bool "Enable driver for PBIAS regulator"
> + ---help---
> + This enables implementation of driver-model regulator uclass
> + features for pseudo-regulator PBIAS found in the OMAP SOCs.
> + This pseudo-regulator is used to provide a BIAS voltage to MMC1
> + signal pads and must be configured properly during a voltage switch.
> + Voltage switching is required by some operating modes of SDcards and
> + eMMC.
> +
> config DM_REGULATOR_LP873X
> bool "Enable driver for LP873X PMIC regulators"
> depends on PMIC_LP873X
> diff --git a/drivers/power/regulator/Makefile b/drivers/power/regulator/Makefile
> index ce14d08..75d611a 100644
> --- a/drivers/power/regulator/Makefile
> +++ b/drivers/power/regulator/Makefile
> @@ -17,5 +17,6 @@ obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o
> obj-$(CONFIG_DM_REGULATOR_SANDBOX) += sandbox.o
> obj-$(CONFIG_REGULATOR_TPS65090) += tps65090_regulator.o
> obj-$(CONFIG_$(SPL_)DM_REGULATOR_PALMAS) += palmas_regulator.o
> +obj-$(CONFIG_$(SPL_)DM_REGULATOR_PBIAS) += pbias_regulator.o
> obj-$(CONFIG_$(SPL_)DM_REGULATOR_LP873X) += lp873x_regulator.o
> obj-$(CONFIG_$(SPL_)DM_REGULATOR_LP87565) += lp87565_regulator.o
> diff --git a/drivers/power/regulator/pbias_regulator.c b/drivers/power/regulator/pbias_regulator.c
> new file mode 100644
> index 0000000..303eca9
> --- /dev/null
> +++ b/drivers/power/regulator/pbias_regulator.c
> @@ -0,0 +1,302 @@
> +/*
> + * (C) Copyright 2016 Texas Instruments Incorporated, <www.ti.com>
> + * Jean-Jacques Hiblot <jjhiblot at ti.com>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <errno.h>
> +#include <dm.h>
> +#include <power/pmic.h>
> +#include <power/regulator.h>
> +#include <regmap.h>
> +#include <syscon.h>
> +#include <linux/bitops.h>
> +#include <linux/ioport.h>
> +#include <dm/read.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +struct pbias_reg_info {
> + u32 enable;
> + u32 enable_mask;
> + u32 disable_val;
> + u32 vmode;
> + unsigned int enable_time;
> + char *name;
> +};
> +
> +struct pbias_priv {
> + struct regmap *regmap;
> + int offset;
> +};
> +
> +static const struct pmic_child_info pmic_children_info[] = {
> + { .prefix = "pbias", .driver = "pbias_regulator"},
> + { },
> +};
> +
> +static int pbias_write(struct udevice *dev, uint reg, const uint8_t *buff,
> + int len)
> +{
> + struct pbias_priv *priv = dev_get_priv(dev);
> + uint32_t val = *(uint32_t *)buff;
> +
> + if (len != 4)
> + return -EINVAL;
> +
> + return regmap_write(priv->regmap, priv->offset, val);
> +}
> +
> +static int pbias_read(struct udevice *dev, uint reg, uint8_t *buff, int len)
> +{
> + struct pbias_priv *priv = dev_get_priv(dev);
> +
> + if (len != 4)
> + return -EINVAL;
> +
> + return regmap_read(priv->regmap, priv->offset, (uint32_t *)buff);
> +}
> +
> +static int pbias_ofdata_to_platdata(struct udevice *dev)
> +{
> + struct pbias_priv *priv = dev_get_priv(dev);
> + struct udevice *syscon;
> + struct regmap *regmap;
> + struct resource res;
> + int err;
> +
> + err = uclass_get_device_by_phandle(UCLASS_SYSCON, dev,
> + "syscon", &syscon);
> + if (err) {
> + error("%s: unable to find syscon device (%d)\n", __func__,
> + err);
> + return err;
> + }
> +
> + regmap = syscon_get_regmap(syscon);
> + if (IS_ERR(regmap)) {
> + error("%s: unable to find regmap (%ld)\n", __func__,
> + PTR_ERR(regmap));
> + return PTR_ERR(regmap);
> + }
> + priv->regmap = regmap;
> +
> + err = dev_read_resource(dev, 0, &res);
> + if (err) {
> + error("%s: unable to find offset (%d)\n", __func__, err);
> + return err;
> + }
> + priv->offset = res.start;
> +
> + return 0;
> +}
> +
> +static int pbias_bind(struct udevice *dev)
> +{
> + int children;
> +
> + children = pmic_bind_children(dev, dev->node, pmic_children_info);
> + if (!children)
> + debug("%s: %s - no child found\n", __func__, dev->name);
> +
> + return 0;
> +}
> +
> +static struct dm_pmic_ops pbias_ops = {
> + .read = pbias_read,
> + .write = pbias_write,
> +};
> +
> +static const struct udevice_id pbias_ids[] = {
> + { .compatible = "ti,pbias-dra7" },
> + { }
> +};
> +
> +U_BOOT_DRIVER(pbias_pmic) = {
> + .name = "pbias_pmic",
> + .id = UCLASS_PMIC,
> + .of_match = pbias_ids,
> + .bind = pbias_bind,
> + .ops = &pbias_ops,
> + .ofdata_to_platdata = pbias_ofdata_to_platdata,
> + .priv_auto_alloc_size = sizeof(struct pbias_priv),
> +};
> +
> +static const struct pbias_reg_info pbias_mmc_omap2430 = {
> + .enable = BIT(1),
> + .enable_mask = BIT(1),
> + .vmode = BIT(0),
> + .disable_val = 0,
> + .enable_time = 100,
> + .name = "pbias_mmc_omap2430"
> +};
> +
> +static const struct pbias_reg_info pbias_sim_omap3 = {
> + .enable = BIT(9),
> + .enable_mask = BIT(9),
> + .vmode = BIT(8),
> + .enable_time = 100,
> + .name = "pbias_sim_omap3"
> +};
> +
> +static const struct pbias_reg_info pbias_mmc_omap4 = {
> + .enable = BIT(26) | BIT(22),
> + .enable_mask = BIT(26) | BIT(25) | BIT(22),
> + .disable_val = BIT(25),
> + .vmode = BIT(21),
> + .enable_time = 100,
> + .name = "pbias_mmc_omap4"
> +};
> +
> +static const struct pbias_reg_info pbias_mmc_omap5 = {
> + .enable = BIT(27) | BIT(26),
> + .enable_mask = BIT(27) | BIT(25) | BIT(26),
> + .disable_val = BIT(25),
> + .vmode = BIT(21),
> + .enable_time = 100,
> + .name = "pbias_mmc_omap5"
> +};
> +
> +static const struct pbias_reg_info *pbias_reg_infos[] = {
> + &pbias_mmc_omap5,
> + &pbias_mmc_omap4,
> + &pbias_sim_omap3,
> + &pbias_mmc_omap2430,
> + NULL
> +};
> +
> +
> +static int pbias_regulator_probe(struct udevice *dev)
> +{
> + const struct pbias_reg_info **p = pbias_reg_infos;
> + struct dm_regulator_uclass_platdata *uc_pdata;
> +
> + uc_pdata = dev_get_uclass_platdata(dev);
> +
> +
> + while (*p) {
> + int rc;
> + rc = dev_read_stringlist_search(dev, "regulator-name",
> + (*p)->name);
> + if (rc >= 0) {
> + debug("found regulator %s\n", (*p)->name);
> + break;
> + } else if (rc != -ENODATA) {
> + return rc;
> + }
> + p++;
> + }
> + if (!*p) {
> + int i = 0;
> + const char *s;
> +
> + debug("regulator ");
> + while (dev_read_string_index(dev, "regulator-name", i++, &s) >= 0)
> + debug("%s'%s' ", (i > 1) ? ", " : "", s);
> + debug("%s not supported\n", (i > 2) ? "are" : "is");
> + return -EINVAL;
> + }
> +
> + uc_pdata->type = REGULATOR_TYPE_OTHER;
> + dev->priv = (void *)*p;
> +
> + return 0;
> +}
> +
> +static int pbias_regulator_get_value(struct udevice *dev)
> +{
> + const struct pbias_reg_info *p = dev_get_priv(dev);
> + int rc;
> + uint32_t reg;
> +
> + rc = pmic_read(dev->parent, 0, (uint8_t *)®, sizeof(reg));
> + if (rc)
> + return rc;
> +
> + debug("%s voltage id %s\n", p->name,
> + (reg & p->vmode) ? "3.0v" : "1.8v");
> + return (reg & p->vmode) ? 3000000 : 1800000;
> +}
> +
> +static int pbias_regulator_set_value(struct udevice *dev, int uV)
> +{
> + const struct pbias_reg_info *p = dev_get_priv(dev);
> + int rc;
> + uint32_t reg;
> +
> + debug("Setting %s voltage to %s\n", p->name,
> + (reg & p->vmode) ? "3.0v" : "1.8v");
> +
> + rc = pmic_read(dev->parent, 0, (uint8_t *)®, sizeof(reg));
> + if (rc)
> + return rc;
> +
> + if (uV == 3000000)
> + reg |= p->vmode;
> + else if (uV == 1800000)
> + reg &= ~p->vmode;
> + else
> + return -EINVAL;
> +
> + return pmic_write(dev->parent, 0, (uint8_t *)®, sizeof(reg));
> +}
> +
> +static int pbias_regulator_get_enable(struct udevice *dev)
> +{
> + const struct pbias_reg_info *p = dev_get_priv(dev);
> + int rc;
> + uint32_t reg;
> +
> + rc = pmic_read(dev->parent, 0, (uint8_t *)®, sizeof(reg));
> + if (rc)
> + return rc;
> +
> + debug("%s id %s\n", p->name,
> + (reg & p->enable_mask) == (p->disable_val) ? "on" : "off");
> +
> + return (reg & p->enable_mask) == (p->disable_val);
> +}
> +
> +static int pbias_regulator_set_enable(struct udevice *dev, bool enable)
> +{
> + const struct pbias_reg_info *p = dev_get_priv(dev);
> + int rc;
> + uint32_t reg;
> +
> + debug("Turning %s %s\n", enable ? "on" : "off", p->name);
> +
> + rc = pmic_read(dev->parent, 0, (uint8_t *)®, sizeof(reg));
> + if (rc)
> + return rc;
> +
> + reg &= ~p->enable_mask;
> + if (enable)
> + reg |= p->enable;
> + else
> + reg |= p->disable_val;
> +
> + rc = pmic_write(dev->parent, 0, (uint8_t *)®, sizeof(reg));
> + if (rc)
> + return rc;
> +
> + if (enable)
> + udelay(p->enable_time);
> +
> + return 0;
> +}
> +
> +static const struct dm_regulator_ops pbias_regulator_ops = {
> + .get_value = pbias_regulator_get_value,
> + .set_value = pbias_regulator_set_value,
> + .get_enable = pbias_regulator_get_enable,
> + .set_enable = pbias_regulator_set_enable,
> +};
> +
> +U_BOOT_DRIVER(pbias_regulator) = {
> + .name = "pbias_regulator",
> + .id = UCLASS_REGULATOR,
> + .ops = &pbias_regulator_ops,
> + .probe = pbias_regulator_probe,
> +};
>
More information about the U-Boot
mailing list