[U-Boot] [PATCH 2/2] arm: socfpga: Enable part command and EFI partition support for DE0-nano-SoC

[Marek Vasut]

On 03/05/2017 01:54 PM, Frank Kunz wrote:
> Those features are used by distro boot with efi boot.
>
> Signed-off-by: Frank Kunz <mailinglists at kunz-im-inter.net>
> ---
> :100644 100644 b122135690... c22b54b48d... M	configs/socfpga_de0_nano_soc_defconfig
>  configs/socfpga_de0_nano_soc_defconfig | 7 ++++---
>  1 file changed, 4 insertions(+), 3 deletions(-)
>
> diff --git a/configs/socfpga_de0_nano_soc_defconfig b/configs/socfpga_de0_nano_soc_defconfig
> index b122135690..c22b54b48d 100644
> --- a/configs/socfpga_de0_nano_soc_defconfig
> +++ b/configs/socfpga_de0_nano_soc_defconfig
> @@ -4,11 +4,11 @@ CONFIG_SYS_MALLOC_F_LEN=0x2000
>  CONFIG_TARGET_SOCFPGA_TERASIC_DE0_NANO=y
>  CONFIG_SPL_STACK_R_ADDR=0x00800000
>  CONFIG_DEFAULT_DEVICE_TREE="socfpga_cyclone5_de0_nano_soc"
> -CONFIG_DEFAULT_FDT_FILE="socfpga_cyclone5_de0_nano_soc.dtb"
>  CONFIG_FIT=y
>  CONFIG_SYS_CONSOLE_IS_IN_ENV=y
>  CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
>  CONFIG_SYS_CONSOLE_ENV_OVERWRITE=y
> +CONFIG_DEFAULT_FDT_FILE="socfpga_cyclone5_de0_nano_soc.dtb"

Is this move needed ? (no, it's not)

>  CONFIG_VERSION_VARIABLE=y
>  # CONFIG_DISPLAY_BOARDINFO is not set
>  CONFIG_SPL=y
> @@ -21,6 +21,7 @@ CONFIG_CMD_ASKENV=y
>  CONFIG_CMD_GREPENV=y
>  # CONFIG_CMD_FLASH is not set
>  CONFIG_CMD_MMC=y
> +CONFIG_CMD_PART=y
>  CONFIG_CMD_SF=y
>  CONFIG_CMD_SPI=y
>  CONFIG_CMD_I2C=y
> @@ -37,6 +38,8 @@ CONFIG_CMD_EXT4_WRITE=y
>  CONFIG_CMD_FAT=y
>  CONFIG_CMD_FS_GENERIC=y
>  CONFIG_CMD_UBI=y
> +CONFIG_EFI_PARTITION=y
> +# CONFIG_SPL_EFI_PARTITION is not set
>  CONFIG_SPL_DM=y
>  CONFIG_DFU_MMC=y
>  CONFIG_DM_GPIO=y
> @@ -59,5 +62,3 @@ CONFIG_G_DNL_MANUFACTURER="terasic"
>  CONFIG_G_DNL_VENDOR_NUM=0x0525
>  CONFIG_G_DNL_PRODUCT_NUM=0xa4a5
>  CONFIG_USE_TINY_PRINTF=y
> -CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION_TYPE=y
> -CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION_TYPE=0xa2

+CC Dalon ...

> \ No newline at end of file
>