[U-Boot] [PATCH v2 1/2] rockchip: rk3399: spl: add UART0 support for SPL

[Philipp Tomsich]

The RK3399-Q7 ("Puma") SoM exposes UART0 as the Qseven UART (i.e. the
serial line available via standardised pins on the edge connector and
available on a RS232 connector).

To support boards (such as the RK3399-Q7) that require UART0 as a
debug console, we match CONFIG_DEBUG_UART_BASE and add the appropriate
iomux setup to the rk3399 SPL code.

As we are already touching this code, we also move the board-specific
UART setup (i.e. iomux setup) into board_debug_uart_init(). This will
be called from the debug UART init when CONFIG_DEBUG_UART_BOARD_INIT
is set.

Signed-off-by: Philipp Tomsich <philipp.tomsich at theobroma-systems.com>
---

Changes in v2:
- Changed hex constant to lowercase

 arch/arm/include/asm/arch-rockchip/grf_rk3399.h |  8 +++++++
 arch/arm/mach-rockchip/rk3399-board-spl.c       | 29 ++++++++++++++++++-------
 2 files changed, 29 insertions(+), 8 deletions(-)

diff --git a/arch/arm/include/asm/arch-rockchip/grf_rk3399.h b/arch/arm/include/asm/arch-rockchip/grf_rk3399.h
index 62d8496..4701cfb 100644
--- a/arch/arm/include/asm/arch-rockchip/grf_rk3399.h
+++ b/arch/arm/include/asm/arch-rockchip/grf_rk3399.h
@@ -333,6 +333,14 @@ enum {
 	GRF_GPIO2B4_SEL_MASK	= 3 << GRF_GPIO2B4_SEL_SHIFT,
 	GRF_SPI2TPM_CSN0	= 1,
 
+	/* GRF_GPIO2C_IOMUX */
+	GRF_GPIO2C0_SEL_SHIFT   = 0,
+	GRF_GPIO2C0_SEL_MASK    = 3 << GRF_GPIO2C0_SEL_SHIFT,
+	GRF_UART0BT_SIN         = 1,
+	GRF_GPIO2C1_SEL_SHIFT   = 2,
+	GRF_GPIO2C1_SEL_MASK    = 3 << GRF_GPIO2C1_SEL_SHIFT,
+	GRF_UART0BT_SOUT        = 1,
+
 	/* GRF_GPIO3A_IOMUX */
 	GRF_GPIO3A4_SEL_SHIFT	= 8,
 	GRF_GPIO3A4_SEL_MASK	= 3 << GRF_GPIO3A4_SEL_SHIFT,
diff --git a/arch/arm/mach-rockchip/rk3399-board-spl.c b/arch/arm/mach-rockchip/rk3399-board-spl.c
index 7b4e0a1..c212143 100644
--- a/arch/arm/mach-rockchip/rk3399-board-spl.c
+++ b/arch/arm/mach-rockchip/rk3399-board-spl.c
@@ -57,19 +57,22 @@ void secure_timer_init(void)
 	writel(TIMER_EN | TIMER_FMODE, TIMER_CHN10_BASE + TIMER_CONTROL_REG);
 }
 
-#define GRF_EMMCCORE_CON11 0xff77f02c
-void board_init_f(ulong dummy)
+void board_debug_uart_init(void)
 {
-	struct udevice *pinctrl;
-	struct udevice *dev;
-	int ret;
-
-	/* Example code showing how to enable the debug UART on RK3288 */
 #include <asm/arch/grf_rk3399.h>
-	/* Enable early UART2 channel C on the RK3399 */
 #define GRF_BASE	0xff770000
 	struct rk3399_grf_regs * const grf = (void *)GRF_BASE;
 
+#if defined(CONFIG_DEBUG_UART_BASE) && (CONFIG_DEBUG_UART_BASE == 0xff180000)
+	/* Enable early UART0 on the RK3399 */
+	rk_clrsetreg(&grf->gpio2c_iomux,
+		     GRF_GPIO2C0_SEL_MASK,
+		     GRF_UART0BT_SIN << GRF_GPIO2C0_SEL_SHIFT);
+	rk_clrsetreg(&grf->gpio2c_iomux,
+		     GRF_GPIO2C1_SEL_MASK,
+		     GRF_UART0BT_SOUT << GRF_GPIO2C1_SEL_SHIFT);
+#else
+	/* Enable early UART2 channel C on the RK3399 */
 	rk_clrsetreg(&grf->gpio4c_iomux,
 		     GRF_GPIO4C3_SEL_MASK,
 		     GRF_UART2DGBC_SIN << GRF_GPIO4C3_SEL_SHIFT);
@@ -80,6 +83,16 @@ void board_init_f(ulong dummy)
 	rk_clrsetreg(&grf->soc_con7,
 		     GRF_UART_DBG_SEL_MASK,
 		     GRF_UART_DBG_SEL_C << GRF_UART_DBG_SEL_SHIFT);
+#endif
+}
+
+#define GRF_EMMCCORE_CON11 0xff77f02c
+void board_init_f(ulong dummy)
+{
+	struct udevice *pinctrl;
+	struct udevice *dev;
+	int ret;
+
 #define EARLY_UART
 #ifdef EARLY_UART
 	/*
-- 
1.9.1